Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 72:08:db:08:ab:60 usb0: HOST MAC 06:aa:78:2c:f3:00 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) ide_gd_mod: module is already loaded soundcore: exports duplicate symbol sound_class (owned by kernel) snd: module is already loaded snd_timer: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) Remounting root file system... EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root root@dm6467t-evm:~# ping      ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1058 (1.0 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:~# ping 192.168.1.106 PING 192.168.1.106 (192.168.1.106): 56 data bytes ping: sendto: Network is unreachable root@dm6467t-evm:~# PHY: 1:01 - Link is Down root@dm6467t-evm:~# root@dm6467t-evm:~# ifconfig ethPHY: 1:01 - Link is Up - 1000/Full 0  ifconfig: eth: error fetching interface information: Device not found root@dm6467t-evm:~# ifo config eth0 192.168.1.102 root@dm6467t-evm:~# ifconfig eth0 netmask         192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# ifonci    co root@dm6467t-evm:~# ifconfig  eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:336 (336.0 B) TX bytes:1058 (1.0 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:~# ping 192.168.1.100 PING 192.168.1.100 (192.168.1.100): 56 data bytes 64 bytes from 192.168.1.100: seq=0 ttl=128 time=3.230 ms 64 bytes from 192.168.1.100: seq=1 ttl=128 time=0.372 ms 64 bytes from 192.168.1.100: seq=2 ttl=128 time=0.328 ms 64 bytes from 192.168.1.100: seq=3 ttl=128 time=0.325 ms 64 bytes from 192.168.1.100: seq=4 ttl=128 time=0.326 ms 64 bytes from 192.168.1.100: seq=5 ttl=128 time=0.370 ms 64 bytes from 192.168.1.100: seq=6 ttl=128 time=0.401 ms 64 bytes from 192.168.1.100: seq=7 ttl=128 time=0.320 ms 64 bytes from 192.168.1.100: seq=8 ttl=128 time=0.363 ms 64 bytes from 192.168.1.100: seq=9 ttl=128 time=0.319 ms  --- 192.168.1.100 ping statistics --- 10 packets transmitted, 10 packets received, 0% packet loss round-trip min/avg/max = 0.319/0.635/3.230 ms root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys /mn n t svc: failed to register lockdv1 RPC service (errno 5). lockd_up: makesock failed, error=-5 idõ Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 4e:ac:2b:e5:ef:55 usb0: HOST MAC c6:4a:b9:53:30:c6 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) soundcore: exports duplicate symbol sound_class (owned by kernel) ide_gd_mod: module is already loaded snd: module is already loaded snd_timer: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) Remounting root file system... EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: ron ot root@dm6467t-evm:~# ifconfgi eth0 192.168.1.102 netmask 255.255.255.0 -sh: ifconfgi: not found root@dm6467t-evm:~# root@dm6467t-evm:~# ifconfgi eth0 192.168.1.102 netmask 255.255.255.0 eth0 192.168.1.102 netmask 255.255.255.0  eth0 192.168.1.102 netmask 255.255.255.0 i eth0 192.168.1.102 netmask 255.255.255.0f eth0 192.168.1.102 netmask 255.255.255.0 eth0 192.168.1.102 netmask 255.255.255.0 g eth0 192.168.1.102 netmask 255.255.255.0 eth0 192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# ping 192.168.1.101 PING 192.168.1.101 (192.168.1.101): 56 data bytes 64 bytes from 192.168.1.101: seq=0 ttl=64 time=1.710 ms 64 bytes from 192.168.1.101: seq=1 ttl=64 time=0.657 ms 64 bytes from 192.168.1.101: seq=2 ttl=64 time=0.459 ms 64 bytes from 192.168.1.101: seq=3 ttl=64 time=0.449 ms 64 bytes from 192.168.1.101: seq=4 ttl=64 time=0.590 ms 64 bytes from 192.168.1.101: seq=5 ttl=64 time=0.376 ms 64 bytes from 192.168.1.101: seq=6 ttl=64 time=0.461 ms  --- 192.168.1.101 ping statistics --- 7 packets transmitted, 7 packets received, 0% packet loss round-trip min/avg/max = 0.376/0.671/1.710 ms root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy/                                         cd mn  /mn root@dm6467t-evm:~# cd /mnt/t  root@dm6467t-evm:/mnt# ls card cf net ram root@dm6467t-evm:/mnt# mkdir nfs root@dm6467t-evm:/mnt# cd  mount -t nfs 192.168.1.101:/home/sprindy/workdir/sile    filesys /mnt/ root@dm6467t-evm:/mnt# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys /mnt/n root@dm6467t-evm:/mnt# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys /mnt/nf root@dm6467t-evm:/mnt# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys /mnt/nfs/ rpcbind: server localhost not responding, timed out rpcbind: server localhost not responding, timed out rpcbind: server localhost not responding, timed out rpcbind: server localhost not responding, timed out svc: failed to register lockdv1 RPC service (errno 5). lockd_up: makesock failed, error=-5 rpcbind: server localhost not responding, timed out rpcbind: server localhost not responding, timed out rpcbind: server localhost not responding, timed out mount: mounting 192.168.1.101:/home/sprindy/workdir/filesys on /mnt/nfs/ failed: Input/output error root@dm6467t-evm:/mnt# PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 1000/Full idå Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 9a:0f:1d:17:61:ff usb0: HOST MAC 22:ab:35:6e:a7:22 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) ide_gd_mod: module is already loaded soundcore: exports duplicate symbol sound_class (owned by kernel) snd: module is already loaded snd_timer: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) Remounting root file system... EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root ]root@dm6467t-evm:~# ]ping 192.1. 68.1.102                   fi  ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1058 (1.0 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:~# fi  ifconfig eth0 192.168.1.102 betnm     b netmask 255.255.255.0 root@dm6467t-evm:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1058 (1.0 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:~# ping 192.168.1.106 PING 192.168.1.106 (192.168.1.106): 56 data bytes  --- 192.168.1.106 ping statistics --- 5 packets transmitted, 0 packets received, 100% packet loss root@dm6467t-evm:~# root@dm6467t-evm:~# ping 192.168.1.106 8 PING 192.168.1.108 (192.168.1.108): 56 data bytes  --- 192.168.1.108 ping statistics --- 6 packets transmitted, 0 packets received, 100% packet loss root@dm6467t-evm:~# PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 100/Full Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC a6:7a:e2:6e:71:6a usb0: HOST MAC 12:b5:4c:23:8c:88 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) soundcore: exports duplicate symbol sound_class (owned by kernel) ide_gd_mod: module is already loaded snd: module is already loaded snd_timer: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) Remounting root file system... snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... PHY: 1:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... Sending select for 192.168.1.102... Sending select for 192.168.1.102... Lease of 192.168.1.102 obtained, lease time 86400 adding dns 192.168.1.1 done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root root@dm6467t-evm:~# ifconfig eth0 192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# ping 192.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes 64 bytes from 192.168.1.108: seq=0 ttl=128 time=1.606 ms 64 bytes from 192.168.1.108: seq=1 ttl=128 time=0.650 ms 64 bytes from 192.168.1.108: seq=2 ttl=128 time=0.340 ms 64 bytes from 192.168.1.108: seq=3 ttl=128 time=0.323 ms 64 bytes from 192.168.1.108: seq=4 ttl=128 time=0.473 ms 64 bytes from 192.168.1.108: seq=6 ttl=128 time=0.363 ms 64 bytes from 192.168.1.108: seq=7 ttl=128 time=0.328 ms 64 bytes from 192.168.1.108: seq=8 ttl=128 time=0.331 ms 64 bytes from 192.168.1.108: seq=9 ttl=128 time=0.372 ms 64 bytes from 192.168.1.108: seq=11 ttl=128 time=0.481 ms 64 bytes from 192.168.1.108: seq=12 ttl=128 time=0.329 ms 64 bytes from 192.168.1.108: seq=13 ttl=128 time=0.329 ms 64 bytes from 192.168.1.108: seq=15 ttl=128 time=0.331 ms 64 bytes from 192.168.1.108: seq=16 ttl=128 time=0.328 ms 64 bytes from 192.168.1.108: seq=17 ttl=128 time=0.374 ms  --- 192.168.1.108 ping statistics --- 18 packets transmitted, 15 packets received, 16% packet loss round-trip min/avg/max = 0.323/0.463/1.606 ms root@dm6467t-evm:~# root@dm6467t-evm:~# ping 192.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes 64 bytes from 192.168.1.108: seq=4 ttl=128 time=0.477 ms 64 bytes from 192.168.1.108: seq=6 ttl=128 time=0.329 ms 64 bytes from 192.168.1.108: seq=7 ttl=128 time=0.582 ms  --- 192.168.1.108 ping statistics --- 10 packets transmitted, 3 packets received, 70% packet loss round-trip min/avg/max = 0.329/0.462/0.582 ms root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy  /worjk  kdir  /filesys  / /m n  root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys/ /m nt/nf  root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys/ /m nt/nfs/ rpcbind: server localhost not responding, timed out svc: failed to register lockdv1 RPC service (errno 5). lockd_up: makesock failed, error=-5 Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 16:65:57:d2:95:85 usb0: HOST MAC a2:5c:64:c9:ee:67 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) soundcore: exports duplicate symbol sound_class (owned by kernel) snd: module is already loaded snd_timer: module is already loaded ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) ide_gd_mod: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) Remounting root file system... EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root root@dm6467t-evm:~# ping      cd root@dm6467t-evm:~# ls root@dm6467t-evm:~# cd / root@dm6467t-evm:/# ls bin etc linuxrc mnt sbin tmp boot home lost+found opt srv usr dev lib media proc sys var root@dm6467t-evm:/# cd me root@dm6467t-evm:/# cd media/ root@dm6467t-evm:/media# ls card hda1 hdd net realroot cf hda2 mmc1 ram union root@dm6467t-evm:/media# cd    ifconfig eth0 192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:/media# ifconfiug  g eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:660 (660.0 B) TX bytes:1058 (1.0 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:/media# ping 16 92.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes  --- 192.168.1.108 ping statistics --- 28 packets transmitted, 0 packets received, 100% packet loss root@dm6467t-evm:/media# PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 100/Full Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  0 DM6467 EVM > DM6467 EVM > printe bootargs=mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 bootcmd=nboot.e 0x80700000 0 0x160000; bootm bootdelay=3 baudrate=115200 bootfile="uImage" addclk=setenv bootargs ${bootargs} clkref=${clkref} ethaddr=00:0e:99:02:b8:55 ethact=DaVinci EMAC serverip=192.168.1.100 ipaddr=192.168.1.102 stdin=serial stdout=serial stderr=serial ver=U-Boot 2009.08 (Jun 21 2010 - 17:39:14) Environment size: 443/16380 bytes DM6467 EVM > setnenv      env boot args     args mem=112M console=ttyS0,115200n8 root=/dev/  v/nfs rw ip=DHCP nff sroot=1921.  .168.1.102:/home/sprintd  dy/workdir/filesys vpif_display.ch2_numbuffers=0 DM6467 EVM > boot Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 28448 Kernel command line: mem=112M console=ttyS0,115200n8 root=/dev/nfs rw ip=DHCP nfsroot=192.168.1.102:/home/sprindy/workdir/filesys vpif_display.ch2_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 112MB = 112MB total Memory: 109140KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 213 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC ae:cf:a1:56:b6:3b usb0: HOST MAC 5a:8f:d4:f3:ac:b2 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) Sending DHCP requests . PHY: 1:01 - Link is Up - 100/Full ..... timed out! IP-Config: Retrying forever (NFS root)... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) Sending DHCP requests . PHY: 1:01 - Link is Up - 100/Full ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.102 IP-Config: Complete: device=eth0, addr=192.168.1.102, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.102, domain=, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.102, rootpath= Looking up port of RPC 100003/2 on 192.168.1.102 rpcbind: server 192.168.1.102 not responding, timed out Root-NFS: Unable to get nfsd port number from server, using default Looking up port of RPC 100005/1 on 192.168.1.102 rpcbind: server 192.168.1.102 not responding, timed out Root-NFS: Unable to get mountd port number from server, using default Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 DM6467 EVM > \ printe bootargs=mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 bootcmd=nboot.e 0x80700000 0 0x160000; bootm bootdelay=3 baudrate=115200 bootfile="uImage" addclk=setenv bootargs ${bootargs} clkref=${clkref} ethaddr=00:0e:99:02:b8:55 ethact=DaVinci EMAC serverip=192.168.1.100 ipaddr=192.168.1.102 stdin=serial stdout=serial stderr=serial ver=U-Boot 2009.08 (Jun 21 2010 - 17:39:14) Environment size: 443/16380 bytes DM6467 EVM > sentenv bootargs mem=112M console=ttyS0  ,115200n8 rr oot=/denv/  v  v/nfs rw ip=DCC  HCP nfsroot=192.168.1.101:/home/sprintd  dy/word kdir/filesys vp   Unknown command 'sentenv' - try 'help' DM6467 EVM > boot    sentenv bootargs mem=112M console=ttyS0,115200n8 root=/dev/nfs rw ip=DHCP nfsroot=192.168.1.101:/home/sprindy/workdir/filesys  printe sentenv bootargs mem=112M console=ttyS0,115200n8 root=/dev/nfs rw ip=DHCP nfsroot=192.168.1.101:/home/sprindy/workdir/filesys   DM6467 EVM > sentenv bootargs mem=112M console=ttyS0,115200n8 root=/dev/nfs rw ip=DHCP nfsroot=192.168.1.101:/home/sprindy/workdir/filesys  printe sentenv bootargs mem=112M console=ttyS0,115200n8 root=/dev/nfs rw ip=DHCP nfsroot=192.168.1.101:/home/sprindy/workdir/filesys Unknown command 'sentenv' - try 'help' DM6467 EVM > setenv bootargs mem=112M console=ttyS0,115200n8 root=/dev/nfs rw ip=DHCP nfsroo DM6467 EVM > t=192.168.1.101:/home/sprindy/workdir/filesys DM6467 EVM > DM6467 EVM > se  setenv bootargs 'mem=112M console=ttyS0,115200n8 root=/dev/nfs nfsroot=192.168.1.101:/home/sprindy/workdir/filesys,nolock ip=dhcp vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0' DM6467 EVM > boot Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 28448 Kernel command line: mem=112M console=ttyS0,115200n8 root=/dev/nfs nfsroot=192.168.1.101:/home/sprindy/workdir/filesys,nolock ip=dhcp vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 112MB = 112MB total Memory: 109140KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 213 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC f6:ae:bd:6a:32:f6 usb0: HOST MAC 5a:4b:0e:3d:65:5b g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) Sending DHCP requests . PHY: 1:01 - Link is Up - 100/Full .,. OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.102 IP-Config: Complete: device=eth0, addr=192.168.1.102, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.102, domain=, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.101, rootpath= Looking up port of RPC 100003/2 on 192.168.1.101 Looking up port of RPC 100005/1 on 192.168.1.101 nfs: server 192.168.1.101 not responding, still trying nfs: server 192.168.1.101 OK VFS: Mounted root (nfs filesystem) on device 0:13. Freeing init memory: 144K nfs: server 192.168.1.101 not responding, still trying nfs: server 192.168.1.101 not responding, still trying PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 1000/Full PHY: 1:01 - Link is Down Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 52:63:8b:a2:bc:aa usb0: HOST MAC 3e:d3:82:37:8b:21 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) soundcore: exports duplicate symbol sound_class (owned by kernel) ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) snd: module is already loaded ide_gd_mod: module is already loaded snd_timer: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) Remounting root file system... snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root root@dm6467t-evm:~# ifconfiPHY: 1:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready    -sh: ifcon: not found root@dm6467t-evm:~# ifconfig eth0 192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# ifconfig        b mou   ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2444 (2.3 KiB) TX bytes:468 (468.0 B) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:~# ping 192;.1   .168.1.101 PING 192.168.1.101 (192.168.1.101): 56 data bytes 64 bytes from 192.168.1.101: seq=1 ttl=64 time=0.822 ms 64 bytes from 192.168.1.101: seq=3 ttl=64 time=0.474 ms 64 bytes from 192.168.1.101: seq=5 ttl=64 time=0.454 ms 64 bytes from 192.168.1.101: seq=7 ttl=64 time=0.480 ms 64 bytes from 192.168.1.101: seq=11 ttl=64 time=0.484 ms 64 bytes from 192.168.1.101: seq=12 ttl=64 time=0.474 ms 64 bytes from 192.168.1.101: seq=13 ttl=64 time=0.531 ms 64 bytes from 192.168.1.101: seq=14 ttl=64 time=0.479 ms 64 bytes from 192.168.1.101: seq=18 ttl=64 time=0.488 ms 64 bytes from 192.168.1.101: seq=21 ttl=64 time=0.628 ms 64 bytes from 192.168.1.101: seq=24 ttl=64 time=0.558 ms 64 bytes from 192.168.1.101: seq=25 ttl=64 time=0.633 ms 64 bytes from 192.168.1.101: seq=28 ttl=64 time=1.017 ms 64 bytes from 192.168.1.101: seq=29 ttl=64 time=0.591 ms 64 bytes from 192.168.1.101: seq=30 ttl=64 time=0.475 ms 64 bytes from 192.168.1.101: seq=31 ttl=64 time=0.608 ms 64 bytes from 192.168.1.101: seq=32 ttl=64 time=0.482 ms 64 bytes from 192.168.1.101: seq=34 ttl=64 time=0.516 ms PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 100/Full 64 bytes from 192.168.1.101: seq=57 ttl=64 time=1004.837 ms 64 bytes from 192.168.1.101: seq=58 ttl=64 time=4.845 ms 64 bytes from 192.168.1.101: seq=59 ttl=64 time=0.500 ms 64 bytes from 192.168.1.101: seq=63 ttl=64 time=0.532 ms 64 bytes from 192.168.1.101: seq=64 ttl=64 time=0.522 ms 64 bytes from 192.168.1.101: seq=75 ttl=64 time=0.489 ms 64 bytes from 192.168.1.101: seq=76 ttl=64 time=0.479 ms 64 bytes from 192.168.1.101: seq=78 ttl=64 time=0.460 ms 64 bytes from 192.168.1.101: seq=80 ttl=64 time=0.611 ms  --- 192.168.1.101 ping statistics --- 81 packets transmitted, 27 packets received, 66% packet loss round-trip min/avg/max = 0.454/37.906/1004.837 ms root@dm6467t-evm:~# PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 1000/Full Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  0 DM6467 EVM > printe bootargs=mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 bootcmd=nboot.e 0x80700000 0 0x160000; bootm bootdelay=3 baudrate=115200 bootfile="uImage" addclk=setenv bootargs ${bootargs} clkref=${clkref} ethaddr=00:0e:99:02:b8:55 ethact=DaVinci EMAC serverip=192.168.1.100 ipaddr=192.168.1.102 stdin=serial stdout=serial stderr=serial ver=U-Boot 2009.08 (Jun 21 2010 - 17:39:14) Environment size: 443/16380 bytes DM6467 EVM > setenv serverip 192.168.1.108 DM6467 EVM > savee Saving Environment to NAND... Erasing Nand... Warning: Erase size 0x00004000 smaller than one erase block 0x00020000 Erasing 0x00020000 instead Erasing at 0x200000 -- 0% complete. Writing to Nand... done DM6467 EVM > boot Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC f6:26:9c:9b:05:63 usb0: HOST MAC 6e:90:eb:fe:6b:30 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) soundcore: exports duplicate symbol sound_class (owned by kernel) ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) snd: module is already loaded snd_timer: module is already loaded ide_gd_mod: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) Remounting root file system... NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: Entering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root root@dm6467t-evm:~# sa etenv        ping 192.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes ping: sendto: Network is unreachable root@dm6467t-evm:~# ifconfig 192.168.1.102 netmask 255.255.255.0e192.168.1.102 netmask 255.255.255.0t192.168.1.102 netmask 255.255.255.0h192.168.1.102 netmask 255.255.255.00192.168.1.102 netmask 255.255.255.0 192.168.1.102 netmask 255.255.255.0192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# root@dm6467t-evm:~# ifconfig eth0 192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# ping 192.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes  --- 192.168.1.108 ping statistics --- 32 packets transmitted, 0 packets received, 100% packet loss root@dm6467t-evm:~# root@dm6467t-evm:~# ping 192.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes  --- 192.168.1.108 ping statistics --- 10 packets transmitted, 0 packets received, 100% packet loss root@dm6467t-evm:~# PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 1000/Full root@dm6467t-evm:~# ifcong  nfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36 errors:0 dropped:0 overruns:0 frame:0 TX packets:43 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2160 (2.1 KiB) TX bytes:2570 (2.5 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3696 (3.6 KiB) TX bytes:3696 (3.6 KiB) root@dm6467t-evm:~# ifconfig u eth0 down root@dm6467t-evm:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3696 (3.6 KiB) TX bytes:3696 (3.6 KiB) root@dm6467t-evm:~# root@dm6467t-evm:~# ifconfig root@dm6467t-evm:~# ifconfig eth0 down    up eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready root@dm6467t-evm:~# PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready root@dm6467t-evm:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36 errors:0 dropped:0 overruns:4294967294 frame:4294967286 TX packets:48 errors:0 dropped:0 overruns:0 carrier:4294967294 collisions:4294967290 txqueuelen:1000 RX bytes:2160 (2.1 KiB) TX bytes:2968 (2.8 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3696 (3.6 KiB) TX bytes:3696 (3.6 KiB) root@dm6467t-evm:~# ping 192.168.1.108 PING 192.168.1.108 (192.168.1.108): 56 data bytes ------------[ cut here ]------------ WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x18c/0x2a0() NETDEV WATCHDOG: eth0 (davinci_emac): transmit queue 0 timed out Modules linked in: dsplinkk cmemk minix ipv6 Backtrace: [] (dump_backtrace+0x0/0x114) from [] (dump_stack+0x18/0x1c) r7:c03f7e10 r6:c029d77c r5:c03cedd7 r4:00000105 [] (dump_stack+0x0/0x1c) from [] (warn_slowpath_common+0x50/0x68) [] (warn_slowpath_common+0x0/0x68) from [] (warn_slowpath_fmt+0x30/0x38) r7:00000024 r6:c0443c98 r5:c31f8000 r4:00000000 [] (warn_slowpath_fmt+0x0/0x38) from [] (dev_watchdog+0x18c/0x2a0) r3:c31f8000 r2:c03cedef [] (dev_watchdog+0x0/0x2a0) from [] (run_timer_softirq+0x1bc/0x280) [] (run_timer_softirq+0x0/0x280) from [] (__do_softirq+0x98/0x12c) [] (__do_softirq+0x0/0x12c) from [] (irq_exit+0x50/0xa8) [] (irq_exit+0x0/0xa8) from [] (asm_do_IRQ+0x74/0x8c) [] (asm_do_IRQ+0x0/0x8c) from [] (__irq_svc+0x4c/0x90) Exception stack(0xc03f7f50 to 0xc03f7f98) 7f40: 00000000 0005317f 0005217f 60000013 7f60: c03f6000 c041e35c c0026e14 c03fa398 80025118 41069265 800250e4 c03f7fa4 7f80: 600000d3 c03f7f98 c002d9d0 c002d9dc 60000013 ffffffff r5:fec48000 r4:ffffffff [] (default_idle+0x0/0x38) from [] (cpu_idle+0x78/0xe4) [] (cpu_idle+0x0/0xe4) from [] (rest_init+0x70/0x84) r5:c041e35c r4:c043292c [] (rest_init+0x0/0x84) from [] (start_kernel+0x268/0x2c0) [] (start_kernel+0x0/0x2c0) from [<80008034>] (0x80008034) ---[ end trace 2c0ad0e13e3cc476 ]--- ide Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  1  0 Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 19304 Kernel command line: mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 76MB = 76MB total Memory: 72628KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 141 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 0a:d0:4e:b3:47:f8 usb0: HOST MAC de:ff:20:86:a4:bf g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 3:1. Freeing init memory: 144K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 141 udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address udevd[1032]: inotify_add_watch(3, (null), 10) failed: Bad address ide_core: exports duplicate symbol generic_ide_ioctl (owned by kernel) snd_page_alloc: exports duplicate symbol snd_free_pages (owned by kernel) ide_gd_mod: module is already loaded soundcore: exports duplicate symbol sound_class (owned by kernel) snd: module is already loaded snd_timer: module is already loaded snd_pcm: module is already loaded snd_soc_core: exports duplicate symbol snd_soc_unregister_codec (owned by kernel) snd_soc_tlv320aic3x: exports duplicate symbol soc_codec_dev_aic3x (owned by kernel) Remounting root file system... NET: Registered protocol family 10 root: mount: mounting rootfs on / failed: No such file or directory EXT2-fs warning (device hda2): ext2_fill_super: mounting ext3 filesystem as ext2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Setting up IP spoofing protection: rp_filter. Configuring network interfaces... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started Sending discover... Sending discover... PHY: 1:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... No lease, failing done. Mon Jan 11 23:16:00 UTC 2010 INIT: eEntering runlevel: 5 Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ERROR: Module cmemk does not exist in /proc/modules ERROR: Module dsplinkk does not exist in /proc/modules CMEMK module: built on Jan 13 2010 at 18:59:45 Reference Linux version 2.6.32 File /sim/scratch_a0850430/arago-install/dvsdk_3_10_00_11/linuxutils_2_25_01_06/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c allocated heap buffer 0xc9000000 of size 0x8f000 cmemk initialized DSPLINK Module (1.64) created on Date: Jan 13 2010 Time: 18:51:20 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm6467t-evm ttyS0 Arago 2009.11 dm6467t-evm ttyS0 dm6467t-evm login: root root@dm6467t-evm:~# root    l PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - 100/Full root@dm6467t-evm:~# ping    ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B8:55 inet6 addr: fe80::20e:99ff:fe02:b855/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:172 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:7 collisions:0 txqueuelen:1000 RX bytes:14574 (14.2 KiB) TX bytes:1058 (1.0 KiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@dm6467t-evm:~# ifconfig eth0 192.168.1.102 netmask 255.255.255.0 root@dm6467t-evm:~# ping 192.168.1.100 PING 192.168.1.100 (192.168.1.100): 56 data bytes 64 bytes from 192.168.1.100: seq=1 ttl=128 time=0.498 ms 64 bytes from 192.168.1.100: seq=2 ttl=128 time=0.412 ms 64 bytes from 192.168.1.100: seq=3 ttl=128 time=0.495 ms 64 bytes from 192.168.1.100: seq=5 ttl=128 time=0.493 ms 64 bytes from 192.168.1.100: seq=6 ttl=128 time=0.330 ms 64 bytes from 192.168.1.100: seq=8 ttl=128 time=0.375 ms 64 bytes from 192.168.1.100: seq=9 ttl=128 time=0.375 ms 64 bytes from 192.168.1.100: seq=10 ttl=128 time=0.324 ms 64 bytes from 192.168.1.100: seq=11 ttl=128 time=0.329 ms 64 bytes from 192.168.1.100: seq=15 ttl=128 time=0.330 ms 64 bytes from 192.168.1.100: seq=16 ttl=128 time=0.337 ms 64 bytes from 192.168.1.100: seq=18 ttl=128 time=0.375 ms 64 bytes from 192.168.1.100: seq=19 ttl=128 time=0.332 ms 64 bytes from 192.168.1.100: seq=20 ttl=128 time=0.337 ms 64 bytes from 192.168.1.100: seq=21 ttl=128 time=0.398 ms 64 bytes from 192.168.1.100: seq=22 ttl=128 time=0.367 ms 64 bytes from 192.168.1.100: seq=23 ttl=128 time=0.368 ms 64 bytes from 192.168.1.100: seq=24 ttl=128 time=0.331 ms  --- 192.168.1.100 ping statistics --- 25 packets transmitted, 18 packets received, 28% packet loss round-trip min/avg/max = 0.324/0.378/0.498 ms root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys /mn t/nfs  root@dm6467t-evm:~# mount -t nfs 192.168.1.101:/home/sprindy/workdir/filesys /mn t/nfs/ rpcbind: server localhost not responding, timed out Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 2009.08 (Jun 21 2010 - 17:39:14) I2C: ready DRAM: 256 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 363MHz DDR Clock :- 297MHz Net: Ethernet PHY: GENERIC @ 0x01 DaVinci EMAC Hit any key to stop autoboot: 3  2  0 DM6467 EVM > DM6467 EVM > printe bootargs=mem=76M console=ttyS0,115200n8 root=/dev/hda1 rw ip=off vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 bootcmd=nboot.e 0x80700000 0 0x160000; bootm bootdelay=3 baudrate=115200 bootfile="uImage" addclk=setenv bootargs ${bootargs} clkref=${clkref} ethaddr=00:0e:99:02:b8:55 ethact=DaVinci EMAC ipaddr=192.168.1.102 serverip=192.168.1.108 stdin=serial stdout=serial stderr=serial ver=U-Boot 2009.08 (Jun 21 2010 - 17:39:14) Environment size: 443/16380 bytes DM6467 EVM > setenv bootargs mem=112M console=ttyS0,115200n8 root=/dev/nfs rw  nfsroot=192.168.1.101:/home/sprindy/workdir/filesys no  ,nolock ip=DHCP vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 DM6467 EVM > boot Loading from NAND 128MiB 3,3V 8-bit, offset 0x160000 Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Arago/2.6.31+2.6.32-rc1-r31+gitr Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2061256 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc2-davinci1 (denis@elrond) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Jan 11 21:45:54 EST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM646x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6467_rev3.x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 28448 Kernel command line: mem=112M console=ttyS0,115200n8 root=/dev/nfs nfsroot=192.168.1.101:/home/sprindy/workdir/filesys ,nolock ip=DHCP vpif_display.ch2_numbuffers=0 vpif_display.ch3_numbuffers=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 112MB = 112MB total Memory: 109140KB available (3876K code, 335K data, 144K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 181.04 BogoMIPS (lpj=905216) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 43 gpio irqs NET: Registered protocol family 16 MUX: Setting register STSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register STSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSOMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: Setting register PTSIMUX_DISABLE PINMUX0 (0x00000000) = 0x00000000 -> 0x00000000 MUX: initialized CIR_UART2 MUX: Setting register CIR_UART2 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000020 MUX: initialized ATAEN MUX: Setting register ATAEN PINMUX0 (0x00000000) = 0x00000000 -> 0x00000001 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pcf857x 1-0038: gpios 145..152 on a pcf8574a pcf857x 1-0038: setup --> -38 vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, pio, peripheral, debug=0 musb_hdrc: USB Peripheral mode controller at fec64000 using PIO, IRQ 13 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 213 io scheduler noop registered io scheduler anticipatory registered (default) CIR device registered successfully (Major = 252, Minor = 0) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) Read MAC addr from EEPROM: 00:0e:99:02:b8:55 Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 ide0: MMIO-DMA hda: TOSHIBA MK4032GAX, ATA DISK drive hda: UDMA/100 mode selected ide0 at 0xfec661f0-0xfec661f7,0xfec663f6 on irq 22 hda: max request size: 512KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "davinci_nand.0": 0x000000000000-0x000000020000 : "params" 0x000000020000-0x000000160000 : "bootloader" 0x000000160000-0x000000560000 : "kernel" 0x000000560000-0x000008000000 : "filesystem" davinci_nand davinci_nand.0: controller rev. 2.2 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 32 KByte at25640a eeprom, pagesize 64 spi_davinci spi_davinci.0: Controller at 0xfec66800 PPP generic driver version 2.4.2 PPP Deflate Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky dm9000 Ethernet Driver, V1.31 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 8e:ad:ce:5a:e0:bf usb0: HOST MAC 06:cf:cd:93:f6:44 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths8200 1-0020: chip found @ 0x40 (DaVinci I2C adapter) ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) vpif_capture vpif_capture: registered sub device ths7353 tvp7002 1-005d: tvp7002 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp7002 vpif_capture vpif_capture: DM646x VPIF Capture driver initialized watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok asoc: DIT <-> davinci-dit mapping ok ALSA device list: #0: DaVinci DM6467 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused uart1 Clocks: disable unused emac Clocks: disable unused timer1 emac-mii: probed drivers/rtc/hctosys.c: unable to open rtc device (rtc0) eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) Sending DHCP requests . PHY: 1:01 - Link is Up - 100/Full ..... timed out! IP-Config: Retrying forever (NFS root)... eth0: attached PHY driver [ET1011C] (mii_bus:phy_addr=1:01, id=282f014) Sending DHCP requests . PHY: 1:01 - Link is Up - 100/Full ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.102 IP-Config: Complete: device=eth0, addr=192.168.1.102, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.102, domain=, nis-domain=(none), bootserver=192.168.1.1, rootserver=192.168.1.101, rootpath= Looking up port of RPC 100003/2 on 192.168.1.101 rpcbind: server 192.168.1.101 not responding, timed out Root-NFS: Unable to get nfsd port number from server, using default Looking up port of RPC 100005/1 on 192.168.1.101 nfs: server 192.168.1.101 not responding, still trying nfs: server 192.168.1.101 OK VFS: Mounted root (nfs filesystem) on device 0:13. Freeing init memory: 144K nfs: server 192.168.1.101 not responding, still trying nfs: server 192.168.1.101 OK nfs: server 192.168.1.101 not r