SK-AM62: [ERROR] XMODEM send failed, no response OR incorrect response from EVM OR cancelled by user,

Turing Alan

Part Number: SK-AM62
Other Parts Discussed in Thread: UNIFLASH

https://software-dl.ti.com/mcu-plus-sdk/esd/AM62X/latest/exports/docs/api_guide_am62x/GETTING_STARTED_FLASH.html

turing@ubuntu:~/ti/mcu_plus_sdk_am62x_08_06_00_18/tools/boot$ python3 uart_uniflash.py -p /dev/ttyUSB0 --cfg=sbl_prebuilt/am62x-sk/default_sbl_ospi_linux.cfg

Parsing config file ...
Parsing config file ... SUCCESS. Found 9 command(s) !!!

Executing command 1 of 9 ...
Found flash writer ... sending sbl_prebuilt/am62x-sk/sbl_uart_uniflash_stage1.release.tiimage
Sending sbl_prebuilt/am62x-sk/sbl_uart_uniflash_stage1.release.tiimage: 0%| | 0/244873 [00:00<?, ?bytes/s]
[ERROR] XMODEM send failed, no response OR incorrect response from EVM OR cancelled by user,
Power cycle EVM and run this script again !!!

我在windows下可以烧录的，为啥ununtu下总是报[ERROR] XMODEM send failed, no response OR incorrect response from EVM OR cancelled by user,
Power cycle EVM and run this script again !!!这个错误

10 个月前

0 Shine 10 个月前

TI__Guru**** 357097 points

Turing Alan 说：
我在windows下可以烧录的

windows下面的烧录命令是怎么写的？

Turing Alan 说：
[ERROR] XMODEM send failed, no response OR incorrect response from EVM OR cancelled by user,

请看一下下面的FAQ。
Flash tool error messages and solutions
https://software-dl.ti.com/mcu-plus-sdk/esd/AM62X/latest/exports/docs/api_guide_am62x/TOOLS_FLASH.html#TOOLS_FLASH_ERROR_MESSAGES

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

win10下用python uart_uniflash.py -p COM33 --cfg=sbl_prebuilt/am62x-sk/default_sbl_ospi_linux.cfg，这个FAQ我看过了，没有解决问题

0 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

已把您的问题升级到英文e2e论坛，请关注下面帖子的回复。
https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1229024/am625-error-xmodem-send-failed-no-response-or-incorrect-response-from-evm-or-cancelled-by-user

0 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

请看下面e2e工程师的回复。

Is the customer using Linux on a Virtual Machine or a dedicated PC. Additionally, is the customer seeing 'C' characters getting printed on UART serial console in Linux before trying the flashing procedure.

Please refer to the following guide: Flash SOC Initialization Binary

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

I have seen 'C' characters using Linux on a Virtual Machine

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

but it fail

0 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

请看下面e2e工程师的回复。

This may be a problem of root access. Could you ask the customer to once try the flashing command with sudo like below

sudo python3 uart_uniflash.py -p /dev/ttyUSB0 --cfg=sbl_prebuilt/am62x-sk/default_sbl_ospi_linux.cfg

Regards,

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

依然不行

0 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

已跟进，请关注e2e帖子的回复。

0 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

请看下面e2e工程师的回复。
I am also running Linux on a Virtual Machine and able to successfully perform the flashing procedure as shown below

Shine said:

Is there any other advice?

Could you please ask the customer to try sending only the first image "sbl_uart_uniflash_stage1.release.tiimage" from some other tools like Picocom, Minicom. If the image is sent successfully with any of these tools, we would know something is wrong with MCU+ SDK UART Uniflash.

To transfer a ROM bootable image (here sbl_uart_uniflash_stage1.release.tiimage) using Picocom, the customer can follow the below procedure:

Power off the board.
Run the below command from the <MCU+ SDK PATH>/tools/boot

Fullscreen

1

sudo picocom -b 115200 -s "sx -vv" /dev/ttyUSB0
Power on the board.
Make sure the UART string comes & character 'C' is getting printed every 2-3 seconds.
Press "Ctrl+A" then "Ctrl+S". Picocom would then ask for the file to be sent.
Enter the file path. The file transfer should start.
If the transfer is successful, Picocom logs "Transfer complete".

A sample run of the above procedure is shown below

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

it can‘t printed character 'C' every 2-3 seconds.

+1 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

请看下面e2e工程师的回复。

The customer confirmed in this response that the 'C' characters were seen. What tool the customer was using before which confirmed the 'C' characters are coming?

Since, we now see that the 'C' characters are not coming, the flashing procedure can't be perfomed. This explains why MCU+ SDK UART Uniflash is failing. Now, first we would want to confirm the UART string & 'C' characters are coming. The first step to that is to make sure we are connected to the right serial port.

Could you please ask the customer to share the output of the command "ls /dev" which would show the devices enumerated by Linux.

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

turing@ubuntu:~$ ls /dev | grep ttyUSB*
ttyUSB0
ttyUSB1
ttyUSB2
ttyUSB3
turing@ubuntu:~$

0 Turing Alan 10 个月前回复 Shine

Prodigy 80 points

I have solved it

Because I don't have Closed the UART terminal as shown below. This is important, else the UART script in next step wont be able to connect to the UART port.

0 Shine 10 个月前回复 Turing Alan

TI__Guru**** 357097 points

好的，非常感谢分享解决办法！

处理器

处理器论坛

SK-AM62: [ERROR] XMODEM send failed, no response OR incorrect response from EVM OR cancelled by user,