CC1310: CC1310 如何修改通信模式？

?? ?

Part Number: CC1310

我需要根据不同的空速修改不同的模式，如下图所示，例如我625空速使用的legacy long range模式，当我切换到5k空速时，我希望使用simplilink long range。

根据各空速生成的smartrf_settings.c文件进行文件对比，我将其中的不同参数已经了修改，但是发现修改后仍然无法通信，我需要知道生成的smartrf_settings.c里面的参数在我主函数哪一步之前调用的，以及如何才能进行参数修改以及切换。下图是修改的部分参数截图，以及在RF初始化之前进行的修改语句。

使用搜索功能，看不到smartrf_setting.c的参数赋值的位置。

1 年多前

0 Nick Sun 1 年多前

TI__Genius 15940 points

您好，

感谢您的对TI产品的关注！为更加有效地解决您的问题，我需要多一些时间查看这款芯片，稍后会为您解答。

0 Nick Sun 1 年多前

TI__Genius 15940 points

您好，

我不确定我是否理解您的问题和您给出的显示的数字。

如果您想要同时使用传统 lrm (625 bps) 和 SimpleLink lrm (5 kbps)，您需要在 smartrf_settings 文件中包含这两种模式的所有设置、覆盖、补丁：

//*********************************************************************************
// Parameter summary
// RX Address0: 0xAA 
// RX Address1: 0xBB 
// RX Address Mode: No address check 
// Frequency: 868.00000 MHz
// Data Format: Serial mode disable 
// Deviation: 5.000 kHz
// Packet Length Config: Variable 
// Max Packet Length: 255 
// Packet Length: 20 
// Packet Data: 255 
// RX Filter BW: 39 kHz
// Symbol Rate: 10.00061 kBaud
// Sync Word Length: 32 Bits 
// TX Power: 14 dBm (requires define CCFG_FORCE_VDDR_HH = 1 in ccfg.c, see CC13xx/CC26xx Technical Reference Manual)
// Whitening: No whitening 

#include "smartrf_settings.h"

#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_lrm.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_lrm.h)

// TI-RTOS RF Mode Object
RF_Mode RF_prop =
{
    .rfMode = RF_MODE_PROPRIETARY_SUB_1,
    .cpePatchFxn = &rf_patch_cpe_lrm,
    .mcePatchFxn = 0,
    .rfePatchFxn = &rf_patch_rfe_lrm
};


// Overrides for CMD_PROP_RADIO_DIV_SETUP
uint32_t pOverrides_625[] =
{
    // override_use_patch_prop_lrm.xml
    // PHY: Use MCE ROM bank 3, RFE RAM patch
    MCE_RFE_OVERRIDE(0,3,0,1,0,0),
    // override_synth_prop_863_930_div5.xml
    // Synth: Set recommended RTRIM to 7
    .
    .
    .
    (uint32_t)0xFFFFFFFF
};


// CMD_PROP_RADIO_DIV_SETUP
// Proprietary Mode Radio Setup Command for All Frequency Bands
rfc_CMD_PROP_RADIO_DIV_SETUP_t RF_cmdPropRadioDivSetup_625 =
{
    .commandNo = 0x3807,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .
    .
    .
    .pRegOverride = pOverrides_625,
    .centerFreq = 0x0364,
    .intFreq = 0x8000,
    .loDivider = 0x05
};


// CMD_FS
// Frequency Synthesizer Programming Command
rfc_CMD_FS_t RF_cmdFs_625 =
{
    .commandNo = 0x0803,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .
    .
};


// CMD_PROP_TX
// Proprietary Mode Transmit Command
rfc_CMD_PROP_TX_t RF_cmdPropTx_625 =
{
    .commandNo = 0x3801,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
   .
   .
   .
};


// CMD_PROP_RX
// Proprietary Mode Receive Command
rfc_CMD_PROP_RX_t RF_cmdPropRx_625 =
{
    .commandNo = 0x3802,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
   .
   .
   .
};


//*********************************************************************************
// Parameter summary
// RX Address0: 0xAA 
// RX Address1: 0xBB 
// RX Address Mode: No address check 
// Frequency: 868.00000 MHz
// Data Format: Serial mode disable 
// Deviation: 5.000 kHz
// Packet Length Config: Variable 
// Max Packet Length: 255 
// Packet Length: 20 
// Packet Data: 255 
// RX Filter BW: 49 kHz
// Symbol Rate: 19.99969 kBaud
// Sync Word Length: 32 Bits 
// TX Power: 14 dBm (requires define CCFG_FORCE_VDDR_HH = 1 in ccfg.c, see CC13xx/CC26xx Technical Reference Manual)
// Whitening: CC1101/CC2500 compatible 

#include "smartrf_settings.h"

#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_sl_longrange.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_sl_longrange.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_mce_sl_longrange.h)

// TI-RTOS RF Mode Object
RF_Mode RF_prop =
{
    .rfMode = RF_MODE_PROPRIETARY_SUB_1,
    .cpePatchFxn = &rf_patch_cpe_sl_longrange,
    .mcePatchFxn = &rf_patch_mce_sl_longrange,
    .rfePatchFxn = &rf_patch_rfe_sl_longrange
};


// Overrides for CMD_PROP_RADIO_DIV_SETUP
uint32_t pOverrides_5k[] =
{
    // override_use_patch_simplelink_long_range.xml
    // PHY: Use MCE RAM patch, RFE RAM patch
    MCE_RFE_OVERRIDE(1,0,0,1,0,0),
    // override_synth_prop_863_930_div5_lbw60k.xml
    // Synth: Set recommended RTRIM to 7
    HW_REG_OVERRIDE(0x4038,0x0037),
    .
    .
    .
    (uint32_t)0xFFFFFFFF
};


// CMD_PROP_RADIO_DIV_SETUP
// Proprietary Mode Radio Setup Command for All Frequency Bands
rfc_CMD_PROP_RADIO_DIV_SETUP_t RF_cmdPropRadioDivSetup_5k =
{
    .commandNo = 0x3807,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .
    .
    .
    .pRegOverride = pOverrides_5k,
    .centerFreq = 0x0364,
    .intFreq = 0x8000,
    .loDivider = 0x05
};


// CMD_FS
// Frequency Synthesizer Programming Command
rfc_CMD_FS_t RF_cmdFs_5k =
{
    .commandNo = 0x0803,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .
    .
    .
};


// CMD_PROP_TX
// Proprietary Mode Transmit Command
rfc_CMD_PROP_TX_t RF_cmdPropTx_5k =
{
    .commandNo = 0x3801,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .
    .
    .
};


// CMD_PROP_RX
// Proprietary Mode Receive Command
rfc_CMD_PROP_RX_t RF_cmdPropRx_5k =
{
    .commandNo = 0x3802,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
   .
   .
   .
};

在PHY间更改，您可以简单地用一个 PHY 打开 RF drive，做任何您想做的事情，然后关闭drive，然后用另一个 PHY 再次打开它。

Smartrf Studio中导出的代码同时只会给你一个PHY，所以你首先要导出一个PHY，重命名它，然后导出另一个，并将设置粘贴到第一个的文件中（或者可以在代码中有两个不同的SmartRF_settings文件，不同的 PHY 具有不同的名称。）

低于 1GHz

低于 1GHz 论坛

CC1310: CC1310 如何修改通信模式？