• RE: LM3409-Q1: 以TI的公板为基础修改LM3409-Q1的驱动参数

  

  Vivian Gao

  I can't say there is anything I know of that is "widely" used. This is not a common use case in automotive LED lighting. If you have the LDP5531EVM then I would probably modify it to see if you can achieve the desired output power. When…

  • 8 个月前
  • 电源管理
  • 电源管理论坛

• LMK1D1208: Inquiry Regarding LMK1D1208 Buffer Output Issues

  

  dong Liu

  TI 认为已经解决

  Part Number: LMK1D1208 Dear TI Technical Support Team, I am currently working on the schematic design for the LMK1D1208 buffer. I have selected a 3.3V single-ended LVCOMS signal as the input, based on the device specifications. However, I have encountered…

  • 1 年多前
  • 时钟和时序
  • 时钟和计时论坛
Answered

• RE: TLV170: 表述问题

  

  Kailyn Chen

  已解决

  您好，这是英文版原版的介绍，可以看到零点频率大于电路带宽，是满足要求的。中文版翻译错了，感谢您的指正。 另外，我把英文版的附上。 Analog Engineer's Circuit Cookbooks.pdf

  • 2 年多前
  • 放大器
  • 放大器论坛

• UCC25600: 使用UCC25600时，设计LLC半桥所遇到的问题

  

  Wuyang Chen

  TI 认为已经解决

  Part Number: UCC25600 I designed an LLC half-bridge resonant boost converter using a UCC25600 controller. The resonant converter has a wide input voltage range of 80V~100V and an output of 450V. The converter has a resonant inductance of 2uH, a resonant…

  • 1 年多前
  • 电源管理
  • 电源管理论坛
Answered

• [参考译文] SN6507-Q1：适用于宽范围输入的电压加倍设计

  

  admin

  已解决

  请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/isolation-group/isolation/f/isolation-forum/1501637/sn6507-q1-voltage-doubling-design-for-wide-range-input 器件型号： SN6507-Q1 工具/软件： 您好： 是否可以对宽范围输入(具有占空比控制)使用双电压配置(Vout…

  • 已回答

  • 8 个月前
  • 隔离（参考译文帖）
  • 隔离（参考译文帖）(Read Only)
Answered

• [参考译文] EDGE-AI-STUDIO：AI 模型用于28P55、但输出不正确

  

  admin

  已解决

  请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/microcontrollers/c2000-microcontrollers-group/c2000/f/c2000-microcontrollers-forum/1489529/edge-ai-studio-the-ai-model-is-used-for-28p55-but-the-output-is-incorrec…

  • 已回答

  • 8 个月前
  • C2000™︎ 微控制器（参考译文帖）
  • C2000™︎ 微控制器（参考译文帖）(Read Only)

• TPS92692-Q1: 14V/60W的boost电路，实际测试只有5W，SS脚是三角波，功率一直调不上去

  

  ph su

  Part Number: TPS92692-Q1 Other Parts Discussed in Thread: TPS92692 TPS92692_Boost_Design_Calculator-7XML2.pdf TPS92692-Q1-X7-V1_1.pdf

  • 1 年多前
  • 电源管理
  • 电源管理论坛

• TDA4VH-Q1: OD dequantization scale is always 0

  

  ?? ?

  TI 认为已经解决

  Part Number: TDA4VH-Q1 HW: TDA4VH evaluation board SDK VER: ti-processor-sdk-rtos-j784s4-evm-09_01_00_06.tar.gz EN: During the model conversion of tidlModelImport, the dequantization scale of the final output is always 0. CHN: tidlModelImport 模型转换，最终输出的反量化scale为…

  • 7 个月前
  • 处理器
  • 处理器论坛

• INA818: The current detection circuit is designed based on the chip, but there is no voltage output at the amplifier output.

  

  Zhou Xin

  TI 认为已经解决

  Part Number: INA818 Based on INA818, I designed the current detection circuit. In the differential input of INA818, I selected 0.1R galvanometer resistor and 49.9R gain RG, which can be amplified 1000 times theoretically. However, in the actual test, it…

  • 1 年多前
  • 放大器
  • 放大器论坛

• Type-C PD with USB3 data transmission

  

  Zhang Peng

  TI 认为已经解决

  We are designing a usb3 hub with PD power output. We are looking for a simple and effective solution to solve the problem of power output of DFP port and type direction of the hub on the basis of meeting usb3 data transmission. At present, the power supply…

  • 1 年多前
  • 接口
  • 接口论坛

未找到您搜索的内容？发布一个新问题吧。