搜索提示
找到 2,868 个结果 查看 问题 帖子 排序依据

  • TPS6594-Q1: TPS6594-Q1 question consultation

    TI 认为已经解决
    Part Number: TPS6594-Q1 EQ1:The data sheet mentions: "Current through input protection FET: Between VSYS_SENSE & VCCA should be lower than 15A", can you describe the detection mechanism of the input current overcurrent protection in detail?…
    • Answered

  • [FAQ] [参考译文] 【常见问题解答】AM62L (AM62L32、AM62L31) 设计建议/定制电路板硬件设计 — 处理器复位输入，复位状态输出和连接建议

    已解决
    Other Parts Discussed in Thread: AM62L , AM625 请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1507929/faq-am62l-am62l32-am62l31-design-recommendations-custom-board-hardware…
    • Answered

  • RE: TLV3601: The SPICE model of the device cannot simulate properly after being imported into ADS.

    已解决
    Hello, links. There is an inconsistency between the PSPICE model (REV E) provided on the official page of the TLV3604 and the TLV3604 model used in the TLV3601-based GaN FET driver circuit reference design in TINA-TI. The model used in the reference design…

  • RE: INA333: INA333的设计问题

    5V供电,输入共模是4V左右的话，输出电压是有限制的，请参见Figure 21. Typical Common-Mode Range vs Output Voltage,希望能满足您的需求。您可以先通过仿真软件验证您的设计。 datasheet: https://www.ti.com/lit/ds/symlink/ina333.pdf#page=10 Simulation model: https://www.ti.com.cn/product/cn/INA333#design-tools-si…

  • MSP430F2618: DAC12 Fullscale range selection issue. (Power consumption of DAC12 module may be increased due to DAC12IR bit selection)

    Part Number: MSP430F2618 Hi I'm using MSP430F2618 DAC12 modulel to generate an analog value as the Vin+ input of a comparator. the schematic is shown as following. The reference voltage is supplied by a MAX9015 which has 1uA output capacity. First…

  • TPS1685: TPS16851

    Part Number: TPS1685 Hi TI partner, I am an ASUS engineer. My project found TPS16851 OCP limit point is 6.262A, SCP limit point is 2.739A, OCP current setting is 6A, SCP is IOCP*1.5, the test results do not match our design, please help us solve it. TPS1685_CALC_v2_FAN_0…

  • RE: BQ25606: 芯片的TS端引脚采样后电压与什么电压做比较？是RENG还是输入端VAC电压？

    您好 ，TS与REGN电压比较 REGN不会低于4.6V，请参考下面的文档确认电路是否有问题。 BQ25606_SchematicChecklist V1p1.pdf
    • Answered

  • RE: [参考译文] TAS2505-Q1：TAS2505开路负载诊断噼啪声问题

    已解决
    请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 您好 Kevin、 目前、在 IC 初始化阶段、页0寄存器65设置为默认值0.0dB。 我应该在此处设置什么值？ 对于静音选项、该值应该是0吗？ 此外、我将分享 PAGE0和页1寄存器值： {PAGE0, SOFTWARE_RESET_REG, 0x01}, // Soft reset {PAGE0, PAGE_SELECT, …
    • Answered

  • [参考译文] OPA817：最大输入和输出电压范围

    已解决
    Other Parts Discussed in Thread: OPA817 请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/amplifiers-group/amplifiers/f/amplifiers-forum/1511327/opa817-maximum-input-and-output-voltage-ranges 器件型号： OPA817 工具/软件： 大家好、在…

  • RE: BQ25730: 對3S3P電池無法充電

    您好，请参考schematic checklist 0552.BQ2570X_BQ2571X_BQ2572X_BQ2573X_SchematicChecklist (6).pdf For layout guidance, please see the following FAQ. https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1032723/faq-how-do-i…

未找到您搜索的内容？发布一个新问题吧。