Other Parts Discussed in Thread: LM5041A , LM5041 , LM5041B 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1293937/uc2827-1-uc2827-1-spice-model 器件型号…
Other Parts Discussed in Thread: LM5041A , LM5041 , LM5041B 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1293937/uc2827-1-uc2827-1-spice-model 器件型号…
Other Parts Discussed in Thread: LM5041A , LM5041 , LM5041B 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1293937/uc2827-1-uc2827-1-spice-model 器件型号…
Part Number: LM5041A Other Parts Discussed in Thread: LM5041 使用LM5041做电流馈电推挽拓扑,使用外部误差放大器,禁用内部误差放大器,LM5041的FB引脚接地;在上电初期,由于误差放大器输出电压与REF引脚电压同时上升,导致REF引脚输出电压只有1.86V左右,而不能达到5V,从而导致整个芯片不能正常工作。请问这是什么原因造成的?该如何处理呢?
Other Parts Discussed in Thread: LM5041 , LM5026 , LM6132 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1063975/lm5026-lm5026-u3a-5041-u4b-feedback…
Other Parts Discussed in Thread: LM5041 , LM5041A 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1060656/power-management-forum 器件型号: LM5041A 主题中讨论的其他器件…
Other Parts Discussed in Thread: LM5041 , CSD19535KTT , LM5102 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/958507/lm5102-lm5102mm-power-dissipation…
Other Parts Discussed in Thread: UC3827-1 , LM5041 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/849713/uc3827-1-simulation-calculation-tool 器件型号: UC3827…