Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/922646/lmg1020-using-serial-resistors-smaller-then-2ohm 器件型号…
Other Parts Discussed in Thread: LMG1020 我使用LMG1020做MOS管驱动,在IN+引脚输入一个脉宽20ns,3.3V的脉冲,在IN-引脚输入一个延时5ns的脉宽20ns,3.3V的脉冲。
按datasheet,输出应该输出一个5ns宽的脉冲信号。但是电路中没有输出。
如果我把IN-直接接地,IN+依然输入一个脉宽20ns,3.3V的脉冲,此时输出会有一个20ns宽的脉冲信号。
请问这个是哪里有问题呢?
谢谢!
Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/866274/lmg1020-operating-frequency 器件型号: LMG1020 您好!
客户问我们 LMG1020是否可以在高于60MHz…
Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/857633/lmg1020-in--pin 器件型号: LMG1020 大家好、
我的客户正在考虑将 LMG1020用于…
Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/857629/lmg1020-pcb-layout 器件型号: LMG1020 您好、 TI 团队,
我参考 TIDA_01573设计了脉冲激光驱动电路…
Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/888541/lmg1020-input-dc-characteristics-is-obscure 器件型号: LMG…
Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/905087/lmg1020-internal-pull-down-up-resistance-for-in-in- …
Other Parts Discussed in Thread: LMG1020 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/858067/lmg1020-latch-up-mode 器件型号: LMG1020 您好!
在突发模式下、当输出低于…