Other Parts Discussed in Thread: LMX2820EVM , LMX2820 , OPA847 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/clock-timing-group/clock-and-timing/f/clock-timing-forum/1504881/lmx2820-active-loop-filter-configuration…
Part Number: OPA657 Other Parts Discussed in Thread: OPA847
如图,两个芯片均为OPA657, 下方未ITA电路;上方未反向比例运放:Rg=1K,Rf=62k,Cf=0;原本反向比例运放是用的OPA847,由于它产生直流偏移,所以想用657来代替,但是焊接好后,发现芯片冒烟了;不知是什么原因。测试过芯片电源引脚电压正常。
Part Number: OPA656 Other Parts Discussed in Thread: OPA847 , ,
如图,电路输出VM2波形如图1所示。输出的波形的尖峰噪声很大。随着反向比例运放的反馈电阻的增大,噪声和信号同步增大(从开始的看不见信号和噪声到信号饱和),但是从噪声明显到信号饱和的过程,噪声感觉有慢慢变小,但是还是明显。这里有2个疑问:
1.这里的尖峰噪声来源是什么? 如果是来源于电源的纹波,那么应该算是共模信号,那么应该会被抑制,而不是和信号同步增大。
2.如何减小这种噪声…
Other Parts Discussed in Thread: LMH34400 , OPA847 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1261065/power-supply-circuit-for-16ch-tia-and-op-…
Other Parts Discussed in Thread: LMH34400 , OPA847 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1261065/power-supply-circuit-for-16ch-tia-and-op-…
Other Parts Discussed in Thread: LMH34400 , OPA847 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1261065/power-supply-circuit-for-16ch-tia-and-op-…
Other Parts Discussed in Thread: LMH34400 , OPA847 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1261065/power-supply-circuit-for-16ch-tia-and-op-…
Other Parts Discussed in Thread: LMH34400 , OPA847 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1261065/power-supply-circuit-for-16ch-tia-and-op-…
Part Number: OPA657 Other Parts Discussed in Thread: OPA847
如图所示,图一图二都家里2.5V偏移。但是图一的交流输出VM1只有20mV VPP,但是图二加上后级放大后,VM1交流电压有1V VPP,请问这是为什么。电流源参数两幅图一致如图一所示。