• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 Hi, I am currently conducting lab 1. After debugging, the ADC is functioning normally, but there is no 0.5 pu output in scope. Is there a problem with the configuration here…

  • 2 个月前
  • 电源管理
  • 电源管理论坛
Answered

• TIDM-02013: TIDM-02013

  

  xqp

  已解决

  Part Number: TIDM-02013 PMP22712：auxiliary power supply Why, the circuit board I replicated according to the schematic diagram actually outputs 24 volts?

  • 已回答

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 Hi, when I built the project and debugged the peoject，I have encountered the following problems. Could you please tell me the solution to the following problem?

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 Hi, May I ask, what is the function of the capacitor connected in parallel across the source and drain terminals?

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 Hi, What is the function of adding a rectifier bridge to the input side of the PFC?

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 hi, If I want to test the PFC or CLLLC power meter separately, how should I activate this code library?

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• RE: RE: TIDM-02013: TIDM-02013

  

  Eirwen

  请参考下面帖子的回复： (+) RE: TIDM-02013: TIDM-02013 - 电源管理论坛 - 电源管理 - E2E 设计支持

  • 3 个月前
  • 电源管理
  • 电源管理论坛
Answered

• TIDM-02013: TIDM-02013

  

  xqp

  已解决

  Part Number: TIDM-02013 Hi，as shown in the figure，lab 1 to 4 are all aimed at verifying the PFC mode. However, why did lab 1 and 2 use DC as the input, rather than AC voltage?

  • 已回答

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 Hello， I compared the ad table with the bom table， Do these components still need to be installed on the OBC board?

  • 4 个月前
  • 电源管理
  • 电源管理论坛

• TIDM-02013: TIDM-02013

  

  xqp

  TI 认为已经解决

  Part Number: TIDM-02013 hi, I want to conduct this experiment 1 alone and check the PWM waveform. How should I proceed? However, after I built it and debugged it, no open-loop PWM waveform was displayed on the oscilloscope (there was no high-voltage…

  • 3 个月前
  • 电源管理
  • 电源管理论坛

未找到您搜索的内容？发布一个新问题吧。