搜索提示
找到 1,112 个结果 查看 问题 帖子 排序依据
    Answered

  • [参考译文] EVM430-FR6043：是否可以使用模拟前端测量水流量@2MHz？

    已解决
    Other Parts Discussed in Thread: MSP430FR6043 请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/microcontrollers/msp-low-power-microcontrollers-group/msp430/f/msp-low-power-microcontroller-forum/1098182/evm430-fr6043…

  • ULC1001-DRV290XEVM: ULC1001-DRV290XEVM

    Part Number: ULC1001-DRV290XEVM Other Parts Discussed in Thread: DRV2901 HI， I used the ULC1001-DRV2901 EVM board to connect the LCS, and then ran the calibration on the GUI. In the water removal mode, the LCS water removal effect was obvious. I used a…
    • Answered

  • [参考译文] MSP430FR6047 :如何找到水流中的气泡

    已解决
    Other Parts Discussed in Thread: MSP430FR6043 , MSP430FR6047 请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/microcontrollers/msp-low-power-microcontrollers-group/msp430/f/msp-low-power-microcontroller-forum/1551279…

  • RE: BQ25185：BQ25185 Solar Energy Management

    Does this happen on multiple boards or just this one? Are you able to measure 5V at VIN? Do you see any current flowing from your VIN supply? Is the supply current-limited? When VSYS is 3.7V with a 3.7V battery connected to BAT, it indicates that the…
    • Answered

  • [参考译文] MSP430FR6043：如何测量无水漂

    已解决
    请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/microcontrollers/msp-low-power-microcontrollers-group/msp430/f/msp-low-power-microcontroller-forum/1552200/msp430fr6043-how-to-measure-no-water-drift 器件型号： MSP430FR6…
    • Answered

  • [参考译文] MSP430FR6043：关于旧计算方法(Quot)；水法(Water method&quot)；和(&quot)；气体方法(Gas method&quot)；。

    已解决
    Other Parts Discussed in Thread: TIDM-02005 , MSP430FR6043 , TIDM-02003 请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/microcontrollers/msp-low-power-microcontrollers-group/msp430/f/msp-low-power-microcontroller-forum…

  • RE: EVM430-FR6043: EVM430-FR6043和TIDA-01486连接后Receiving Stage问题

    Hi Daniel, EVM430-FR6043 had been testes individually for water flow meter, and it worked normally. I am sure the connection of the two board is correct. I found the below thread, the question in which is very similar to mine. Finally I changed the C51…
    • Answered

  • [参考译文] MSP430FR6047：水质与超声波测量之间的关系

    已解决
    请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/microcontrollers/msp-low-power-microcontrollers-group/msp430/f/msp-low-power-microcontroller-forum/1200026/msp430fr6047-the-relationship-between-water-quality-and-ultrasonic…

  • TIDM-02013: There is no driving waveform on the circuit mainboard.

    TI 认为已经解决
    Part Number: TIDM-02013 When the control card is not inserted into the tdim-02013, the GPIO port can detect the output PWM waveform. When the control card is inserted, the voltage across C164 is measured, but no voltage PWM signal can be detected. What…
    • Answered

  • RE: EVM430-FR6043: 无法与Ultrasonic Sensing Design Center连接

    已解决
    您好， Vivian 说： 偶尔会显示已找到设备，但无法连接 请更换USB口试一下，电脑设备管理器上能正常识别吗？ 如果仍然有问题，请参考“3 Flashing the EVM and Installing the GUI ” 尝试重新烧录一下固件 Quick Start Guide for Gas Flow Meter

未找到您搜索的内容？发布一个新问题吧。