Other Parts Discussed in Thread: TPS62A06 , TPS62065 , TPS62867 , LM21212-2 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1470152/tps62867-life-cycl…
Other Parts Discussed in Thread: TPS62065 Hello,
最近在对电源的环路稳态进行AC扫描分析时,按照pspice的方法来进行仿真发现得出来的波形不太正常,不确定下图的操作方法是否正确。使用的电源模型是TPS62065。
然后波形中的问题是环路增益一直为负DB,没办法找到穿越频率,另外想确定下这两个Y轴单位,和伯德图的单位似乎不一样,相角对应数值为0D,增益对应数值为-100。
Part Number: LMR23630-Q1 Other Parts Discussed in Thread: TPS62065-Q1 Hi Team,
just want to check the next gen of TPS62065-Q1.
please also kindly help provide comparison table. Thanks.
Other Parts Discussed in Thread: TPS62065 , TLV62568 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/tools/simulation-hardware-system-design-tools-group/sim-hw-system-design/f/simulation-hardware-system-design-tools…
Other Parts Discussed in Thread: TPS62067-Q1 , TPS62065-Q1 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1554960/tps62067-q1-tps62067-q1-stability…
Other Parts Discussed in Thread: TPS62065 , TPS62170 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1035352/tps62170-vout-gap-between-pwm-and-pfm 器件型号…
Other Parts Discussed in Thread: TPS62065 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/949186/tps62056-threshold-of-power-save-mode 器件型号: TPS62056 …
Other Parts Discussed in Thread: TLV62569 , TPS62065 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/712441/tlv62569-spec-vih-vil-definition-on-en-p…
Other Parts Discussed in Thread: TPS62060 , TPS62065 我这边用了TPS62060,1颗1.6A的DC/DC芯片
电源拓扑是3.3V转1.2V给处理器。
我们的处理器在功能模式切换时,1.2V的电流波动比较大,电流最小值是0.7A,最大值是1.1A,约有400mA的波动。
这个电流波动导致的1.2V电压波动,我们的处理器是能接受的。
但由于1.2V的电流波动,导致3.3V部分电压稳定度变差,我们的射频部分就不能接受变差的3.3V的电源稳定度。
我这边做了个实验…