Answered

• BQ25756: Designed a charging circuit using the BQ25756, but it failed to operate properly.

  

  建忠 蔡

  已解决

  Part Number: BQ25756 The issue is as described in the subject line: 1、The design parameters are as follows: the input source is 57–60 V, and the charging output is 56 V / 2 A. The ACUV pin is measured at 7.4 V and the ACOV pin at 3.4 V, which meet the…

  • 已回答

  • 16 天前
  • 电源管理
  • 电源管理论坛

• MSP430AFE253: Which front-end circuit design is better for a Sigma-Delta ADC?

  

  haoyang Xu

  TI 认为已经解决

  Part Number: MSP430AFE253 Many documents mention that using a SD ADC requires adding an anti-aliasing RC circuit as its front-end for differential inputs, as shown in the first figure below. Actual tests on the MSP430AFE's SD24_A achieved a sampling ripple…

  • 4 个月前
  • MSP 低功耗微控制器
  • MSP 低功耗微控制器论坛

• RE: ADS1231: I used ADS1231 chip to collect strain gauge data and found some problems during use. Please help me check the rationality of the circuit design

  

  yang liu

  Hello, have you received my reply? Could you please help me analyze if there are any issues with the circuit design? What areas need to be optimized? （已压缩）核心原理图.pdf

  • 1 个月前
  • 数据转换器
  • 数据转换器论坛

• Why Are Engineers Shifting from BJTs to MOSFETs in Push-Pull Circuits? Key Differences, Tradeoffs, and Design Pitfalls to Discuss

  

  vbsemi

  TI 认为已经解决

  Other Parts Discussed in Thread: UCC27517 Hi fellow engineers and TI community members, I’ve been working on optimizing a push-pull converter design (12V input, 5A output) and noticed a trend: many peers are swapping out traditional BJTs for…

  • 3 个月前
  • 电源管理
  • 电源管理论坛

• DS125DF111: How to design the PRBS generator function on the circuit

  

  Ling Tien

  TI 认为已经解决

  Part Number: DS125DF111 Other Parts Discussed in Thread: DS110DF410 , Dear Sir/Madam, We want to use the PRBS generator function for the following requirements, could you help us check which component we should select: DS125DF111, DS123DF410, or DS110DF410…

  • 7 个月前
  • 接口
  • 接口论坛
Answered

• [参考译文] WEBENCH-CIRCUIT-DESIGNER：LM51561H-Q1PWP

  

  admin

  已解决

  请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1388001/webench-circuit-designer-lm51561h-q1pwp 器件型号： WEBENCH-CIRCUIT-DESIGNER 工具与软件： 我计划 使用 WebBench…

  • 已回答

  • 1 年多前
  • 电源管理（参考译文帖）
  • 电源管理（参考译文帖）(Read Only)

• TPS35: How to design an output Latching circuit using the TPS35AA38AGA?

  

  jianhao chen

  TI 认为已经解决

  Part Number: TPS35 HI，There is an open-drain reset output latch application。How to design an output Latching circuit using the TPS35AA38AGA?

  • 1 年多前
  • 电源管理
  • 电源管理论坛

• INA818: The current detection circuit is designed based on the chip, but there is no voltage output at the amplifier output.

  

  Zhou Xin

  TI 认为已经解决

  Part Number: INA818 Based on INA818, I designed the current detection circuit. In the differential input of INA818, I selected 0.1R galvanometer resistor and 49.9R gain RG, which can be amplified 1000 times theoretically. However, in the actual test, it…

  • 1 年多前
  • 放大器
  • 放大器论坛

• WEBENCH-POWER-DESIGNER: WEBENCH@power designer打不开

  

  Tuo_Tuoo

  TI 认为已经解决

  Part Number: WEBENCH-POWER-DESIGNER https：//webench.ti.com/power designer/一直打不开 ，显示error

  • 1 年多前
  • 仿真、硬件和系统设计工具
  • 仿真、硬件和系统设计工具论坛
Answered

• [参考译文] WEBENCH-POWER-DESIGNER：共享 Webench 文件

  

  admin

  已解决

  请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/tools/simulation-hardware-system-design-tools-group/sim-hw-system-design/f/simulation-hardware-system-design-tools-forum/1483109/webench-power-designer-sharing-webench…

  • 已回答

  • 7 个月前
  • 仿真、硬件和系统设计工具（参考译文帖）
  • 仿真、硬件和系统设计工具（参考译文帖）(Read Only)

未找到您搜索的内容？发布一个新问题吧。