[参考译文] MSPM0L1306：计时器的通用发布者事件示例

您好、Gary Gao、

将 DMA 目标地址设置为缓冲器的原因是首先测试 DMA 触发源。 这不是问题。

我猜问题的原因是 DMA 用户设置。

DL_DMA_setSubscriberChanID 函数不会自动包含在 SysConfig 生成的文件中。

我正在尝试实现下图。 并尝试使用 DMA 而不是 SW 写入 TIMx.LOAD = A。

ST 已提供示例和参考、如下链接所示。

https://community.st.com/t5/stm32-mcus/custom-signal-generation-using-pwm-and-dma/ta-p/49809

下面是我简单针对 PWM 和 DMA 操作测试的代码。

它似乎工作正常、但我不知道我是否设置正确。

e2e.ti.com/.../7723.ti_5F00_msp_5F00_dl_5F00_config.ce2e.ti.com/.../4452.ti_5F00_msp_5F00_dl_5F00_config.h

/*
 * Copyright (c) 2021, Texas Instruments Incorporated
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * *  Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 * *  Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * *  Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
 * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#include "ti_msp_dl_config.h"



#define DMA_TRANSFER_SIZE_WORDS (16)

const uint16_t gSrcData[DMA_TRANSFER_SIZE_WORDS] =
{1000, 5000, 10000, 15000, 20000, 25000, 30000, 35000,
 40000, 45000, 49999, 40000, 30000, 20000, 10000, 2000};

uint16_t gDstData;

volatile bool gChannel0InterruptTaken = false;

volatile uint32_t gUpdateCnt;


int main(void)
{
    SYSCFG_DL_init();

    gUpdateCnt = 0;
    DL_TimerG_startCounter(PWM_0_INST);

    /* Setup interrupts on device */
    DL_SYSCTL_disableSleepOnExit();
    NVIC_EnableIRQ(DMA_INT_IRQn);

    /* Configure DMA source, destination and size */
    DL_DMA_setSrcAddr(DMA, DMA_CH0_CHAN_ID, (uint32_t) &gSrcData[0]);
    DL_DMA_setDestAddr(DMA, DMA_CH0_CHAN_ID, (uint32_t)(&PWM_0_INST->COUNTERREGS.CC_01[0]));
    DL_DMA_setTransferSize(DMA, DMA_CH0_CHAN_ID, DMA_TRANSFER_SIZE_WORDS);
    DL_DMA_setSubscriberChanID(DMA, DL_DMA_SUBSCRIBER_INDEX_0, PWM_0_INST_PUB_0_CH);
    DL_DMA_enableChannel(DMA, DMA_CH0_CHAN_ID);


    gChannel0InterruptTaken = false;
    DL_DMA_startTransfer(DMA, DMA_CH0_CHAN_ID);

    /* Wait for transfer */
    while (gChannel0InterruptTaken == false) {
        __WFE();
    }

    /* Breakpoint to inspect verification result */
    __BKPT(0);


    while (1)
    {
        __WFI();
    }
}

void PWM_0_INST_IRQHandler(void)
{
    switch (DL_TimerG_getPendingInterrupt(PWM_0_INST))
    {
        case DL_TIMERG_IIDX_CC0_DN:
            gUpdateCnt++;
            default:
                break;
    }
}

void DMA_IRQHandler(void)
{
    /* Example interrupt code -- just used to break the WFI in this example */
    switch (DL_DMA_getPendingInterrupt(DMA)) {
        case DMA_IIDX_STAT_DMACH0:
            gChannel0InterruptTaken = true;
            break;
        default:
            break;
    }
}

使用 SysConfig 正确执行配置吗？ 如果是这样、那么代码应该没有问题。