请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。
部件号：AM5728 你好。
我有基于 am5728的定制板。
在我的系统中，我有两个 PCI 桥接器和一个带有 FPGA 的自定义 PCI 板。
在 Linux 启动后，我尝试从 PCI 板读取内存并获得此结果
(我在未成功收到附件的情况下开始使用 devmem2来读取驱动程序中的内存以用于此主板
请注意，内核消息在电源重置后仅出现一次，并读取0x20200000地址)：
root@am57xx-EVM：Δ T~# devmem2 0x20200000
/dev/mem 已打开。
[1036.130101] OMA_L3_NOC 44000000.OCP：L3应用程序错误：目标5 mod:1 (不可清除)
映射到地址0xb6fd1000的内存。
读取地址0x2020000 [1036.138297] OMAP_L3_NOC 44000000.OCP：L3调试错误：目标5 mod:1 (不可清除)
0 (0xb6fd1000)：0xFFFFFFFF
如果我尝试从 PCI 桥读取内存，我会得到另一个答案，而不会收到内核消息：
root@am57xx-EVM：Δ T~# devmem2 0x20400000
/dev/mem 已打开。
映射到地址0xb6fba000的内存。
请在地址0x20400000 (0x6fba000)处阅读：0x860910B5
我在论坛上阅读了一些线索，但没有解决我的问题。 我决定检查错误。
从14.2.4.2.1.1.2起，随后：TRM 中的 L3_main Interconnect Protection Violation Error Identification (三级主互连保护违规错误标识) I 检查：
L3_FLAGMUX _REGERR0 [31:0] REGERROR0 (所有值均为零)：
根@am57xx-EVM：~#设备内存2 0x4480350C
/dev/mem 已打开。
内存映射地址为0xb6f73000。
读取地址0x4480350C (0x6f7350c): 0x00000000
根@am57xx-EVM：~#设备2 0x4480360C
/dev/mem 已打开。
内存映射到地址0xb6fe6000。
读取地址0x4480360C (0x6fe660c)：0x00000000
root@am57xx-EVM：Δ~# devmem2 0x4500020C
/dev/mem 已打开。
内存映射到地址0xb6fb3000。
读取地址0x4500020C (0x6fb320c): 0x00000000
Ctrl_core_SEC_ERR_STATUS_FUNC_1 (值为零)：
root@am57xx-EVM：Δ~# devmem2 0x4A002148
/dev/mem 已打开。
映射到地址0xb6fd8000的内存。
读取地址0x4A002148 (0x6fd8148)：0x00000000
L3_FLAGMUX_REGERR1 (所有值均为零)：
根@am57xx-EVM：~#设备内存2 0x44803514
/dev/mem 已打开。
内存映射地址为0xb6f79000。
读取地址0x44803514 (0x6f79514)：0x00000000
root@am57xx-EVM：~#设备内存2 0x44803614
/dev/mem 已打开。
内存映射地址为0xb6f37000。
读取地址0x44803614 (0x6f37614)：0x00000000
root@am57xx-EVM：Δ T~# devmem2 0x45000214
/dev/mem 已打开。
映射到地址0xb6f3a000的内存。
读取地址0x45000214 (0x6f3a214)：0x00000000
从14.2.4.2.1.1.3后续版本：TRM 中的 L3_main 互连标准错误标识 I 检查：
L3_TAGR_STDERRLOG_MAIN (所有值均为零)：
/dev/mem opened. Memory mapped at address 0xb6f9e000. Read at address 0x44000148 (0xb6f9e148): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fc5000. Read at address 0x44000248 (0xb6fc5248): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f9f000. Read at address 0x44000348 (0xb6f9f348): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fbf000. Read at address 0x44000548 (0xb6fbf548): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fe1000. Read at address 0x44000648 (0xb6fe1648): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fa3000. Read at address 0x44000748 (0xb6fa3748): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f14000. Read at address 0x44000848 (0xb6f14848): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fc5000. Read at address 0x44000948 (0xb6fc5948): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fd3000. Read at address 0x44001148 (0xb6fd3148): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fc1000. Read at address 0x44002F48 (0xb6fc1f48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f00000. Read at address 0x44003048 (0xb6f00048): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f09000. Read at address 0x44003148 (0xb6f09148): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f86000. Read at address 0x44000D48 (0xb6f86d48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f6c000. Read at address 0x44000C48 (0xb6f6cc48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fb4000. Read at address 0x44000A48 (0xb6fb4a48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f9d000. Read at address 0x44000B48 (0xb6f9db48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fbb000. Read at address 0x44000E48 (0xb6fbbe48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f0c000. Read at address 0x44000F48 (0xb6f0cf48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f68000. Read at address 0x44001048 (0xb6f68048): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f6d000. Read at address 0x44001248 (0xb6f6d248): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6faa000. Read at address 0x44001348 (0xb6faa348): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f7c000. Read at address 0x44001448 (0xb6f7c448): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f0f000. Read at address 0x44001648 (0xb6f0f648): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f69000. Read at address 0x44001748 (0xb6f69748): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f0b000. Read at address 0x44001848 (0xb6f0b848): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f0a000. Read at address 0x44001948 (0xb6f0a948): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f7d000. Read at address 0x44001C48 (0xb6f7dc48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f05000. Read at address 0x44001D48 (0xb6f05d48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fc9000. Read at address 0x44001F48 (0xb6fc9f48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f68000. Read at address 0x44002048 (0xb6f68048): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f68000. Read at address 0x44002148 (0xb6f68148): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fd1000. Read at address 0x44002248 (0xb6fd1248): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f56000. Read at address 0x44002348 (0xb6f56348): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f16000. Read at address 0x44002448 (0xb6f16448): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fcb000. Read at address 0x44002548 (0xb6fcb548): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f0a000. Read at address 0x44002648 (0xb6f0a648): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fb0000. Read at address 0x44002748 (0xb6fb0748): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f09000. Read at address 0x44002848 (0xb6f09848): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f08000. Read at address 0x44002948 (0xb6f08948): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f1e000. Read at address 0x44002B48 (0xb6f1eb48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f6d000. Read at address 0x44002E48 (0xb6f6de48): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6f05000. Read at address 0x44003748 (0xb6f05748): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fe9000. Read at address 0x44003948 (0xb6fe9948): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6ff5000. Read at address 0x45000148 (0xb6ff5148): 0x00000000 /dev/mem opened. Memory mapped at address 0xb6fb4000. Read at address 0x45000348 (0xb6fb4348): 0x00000000
L3_FLAGMUX_REGERR0 (0x4480360C 值为0x00000020)。 在出现 L3应用程序错误之前，此值为0x00000000)：
根@am57xx-EVM：~#设备内存2 0x4480350C
/dev/mem 已打开。
内存映射地址为0xb6fcf000。
请在地址0x4480350C (0x6fcf50c): 0x00000000处阅读
根@am57xx-EVM：~#设备2 0x4480360C
/dev/mem 已打开。
内存映射地址为0xb6f65000。
读取地址0x4480360C (0xb6f6560c): 0x00000020
root@am57xx-EVM：Δ~# devmem2 0x4500020C
/dev/mem 已打开。
内存映射到地址0xb6fb1000。
读取地址0x4500020C (0x6fb120c)：0x00000000
L3_FLAGMUX_MASK1 (0x44803610值为0x007FFDF。 在出现 L3应用程序错误之前，此值为0x007FFFFF)：
root@am57xx-EVM：~#设备2 0x44803510
/dev/mem 已打开。
映射到地址0xb6f9c000的内存。
请参阅地址0x44803510 (0x6f9c510)：0xFFFFFFFF
root@am57xx-EVM：~#设备内存2 0x44803610
/dev/mem 已打开。
内存映射地址为0xb6f36000。
读取地址0x44803610 (0x6f36610)：0x007FFDF
root@am57xx-EVM：Δ T~# devmem2 0x45000210
/dev/mem 已打开。
映射到地址0xb6fdb000的内存。
读取地址0x45000210 (0x6fdb210)：0x00000000
L3_FLAGMUX_REGERR1 (0x44803614值为0x00000020)。 在出现 L3应用程序错误之前，此值为0x00000000)：
根@am57xx-EVM：~#设备内存2 0x44803514
/dev/mem 已打开。
映射到地址0xb6f49000的内存。
读取地址0x44803514 (0x6f49514)：0x00000000
root@am57xx-EVM：~#设备内存2 0x44803614
/dev/mem 已打开。
内存映射地址为0xb6f26000。
请参阅地址0x44803614 (0xb6f26614)：0x00000020
root@am57xx-EVM：Δ T~# devmem2 0x45000214
/dev/mem 已打开。
映射到地址0xb6fa9000的内存。
读取地址0x45000214 (0xb6fa9214)：0x00000000
下一页在表14-24中。 互连标志映射我找不到0x00000020 (32)值。
出现此错误的原因是什么？
为什么我无法从 PCIe 板读取内存？
是我的原因还是 PCI borard 显影剂的原因？
请你提出建议为荷。
板载配置空间命令寄存器值为0x0546，即平均内存空间启用位已设置。
以下是我的系统的附加信息：
从 lspci：
There is pci-devices tree:
root@am57xx-evm:~# /usr/sbin/lspci -t
-[0000:00]---00.0-[01-ff]--+-00.0-[02-11]--+-01.0-[03]--
| +-04.0-[04]--
| +-05.0-[05]----00.0
| +-06.0-[06]--
| +-07.0-[07]--
| +-08.0-[08]--
| \-09.0-[09-11]--+-00.0-[0a-11]--+-01.0-[0b]--
| | +-04.0-[0c]--
| | +-05.0-[0d]--
| | +-06.0-[0e]--
| | +-07.0-[0f]--
| | +-08.0-[10]--
| | \-09.0-[11]--
| \-00.1
\-00.1
There is pci-devices config spaces:
root@am57xx-evm:~# /usr/sbin/lspci -x
00:00.0 PCI bridge: Texas Instruments Multicore DSP+ARM KeyStone II SOC (rev 01)
00: 4c 10 88 88 47 05 10 00 01 00 04 06 10 00 01 00
10: 04 00 10 20 00 00 00 00 00 01 ff 00 f0 00 00 20
20: 20 20 40 20 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a6 01 01 00
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 46 05 10 00 ba 00 04 06 10 00 81 00
10: 00 00 40 20 00 00 00 00 01 02 11 00 f1 01 00 00
20: 20 20 30 20 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a6 01 01 00
01:00.1 System peripheral: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 40 01 10 00 ba 00 80 08 10 00 80 00
10: 00 00 42 20 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 b5 10 09 86
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 02 00 00
02:01.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 03 03 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a9 01 01 00
02:04.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 04 04 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a6 01 01 00
02:05.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 46 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 05 05 00 f1 01 00 00
20: 20 20 20 20 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a9 01 01 00
02:06.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 06 06 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ad 01 01 00
02:07.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 07 07 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 af 01 01 00
02:08.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 08 08 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a6 01 01 00
02:09.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 46 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 02 09 11 00 f1 01 00 00
20: 30 20 30 20 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a9 01 01 00
05:00.0 System peripheral: Altera Corporation Device 0005 (rev 01)
00: 72 11 05 00 40 01 10 00 01 00 80 08 10 00 00 00
10: 00 00 20 20 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 72 11 05 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 00 01 00 00
09:00.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 46 05 10 00 ba 00 04 06 10 00 81 00
10: 00 00 30 20 00 00 00 00 09 0a 11 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a9 01 01 00
09:00.1 System peripheral: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 40 01 10 00 ba 00 80 08 10 00 80 00
10: 00 00 32 20 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 b5 10 09 86
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 02 00 00
0a:01.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 0b 0b 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ad 01 01 00
0a:04.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 0c 0c 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a9 01 01 00
0a:05.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 0d 0d 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ad 01 01 00
0a:06.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 0e 0e 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 af 01 01 00
0a:07.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 0f 0f 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a6 01 01 00
0a:08.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 10 10 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 a9 01 01 00
0a:09.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
00: b5 10 09 86 44 05 10 00 ba 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 0a 11 11 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ad 01 01 00
root@am57xx-evm:~# /usr/sbin/lspci -nn
00:00.0 PCI bridge [0604]: Texas Instruments Multicore DSP+ARM KeyStone II SOC [104c:8888] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
01:00.1 System peripheral [0880]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:04.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:05.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:06.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:07.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:08.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
02:09.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
05:00.0 System peripheral [0880]: Altera Corporation Device [1172:0005] (rev 01)
09:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
09:00.1 System peripheral [0880]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:04.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:05.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:06.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:07.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:08.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
0a:09.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA [10b5:8609] (rev ba)
root@am57xx-evm:~# /usr/sbin/lspci -vv
00:00.0 PCI bridge: Texas Instruments Multicore DSP+ARM KeyStone II SOC (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 167
Region 0: Memory at 20100000 (64-bit, non-prefetchable) [size=1M]
Bus: primary=00, secondary=01, subordinate=ff, sec-latency=0
I/O behind bridge: None
Memory behind bridge: 20200000-204fffff [size=3M]
Prefetchable memory behind bridge: None
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000ae0f1000 Data: 0000
Capabilities: [70] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x2, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
RootCmd: CERptEn+ NFERptEn+ FERptEn+
RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
Kernel driver in use: pcieport
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 168
Region 0: Memory at 20400000 (32-bit, non-prefetchable) [size=128K]
Bus: primary=01, secondary=02, subordinate=11, sec-latency=0
I/O behind bridge: None
Memory behind bridge: 20200000-203fffff [size=2M]
Prefetchable memory behind bridge: None
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000ae0f1000 Data: 0001
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Upstream Port, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
AtomicOpsCtl: EgressBlck-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100 v1] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [138 v1] Power Budgeting <?>
Capabilities: [148 v1] Virtual Channel
Caps: LPEVC=1 RefClk=100ns PATEntryBits=4
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=06 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32+ WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=WRR32 TC/VC=ff
Status: NegoPending- InProgress-
Port Arbitration Table <?>
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=1 ArbSelect=Fixed TC/VC=00
Status: NegoPending+ InProgress-
Capabilities: [448 v1] Vendor Specific Information: ID=0000 Rev=0 Len=0cc <?>
Capabilities: [950 v1] Vendor Specific Information: ID=0001 Rev=0 Len=010 <?>
Kernel driver in use: pcieport
...........
02:05.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 172
Bus: primary=02, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: None
Memory behind bridge: 20200000-202fffff [size=1M]
Prefetchable memory behind bridge: None
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000ae0f1000 Data: 0004
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <2us
ClockPM- Surprise+ LLActRep+ BwNot+ ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #5, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd+
AtomicOpsCap: Routing-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
AtomicOpsCtl: EgressBlck-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100 v1] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [148 v1] Virtual Channel
Caps: LPEVC=1 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=1 ArbSelect=Fixed TC/VC=00
Status: NegoPending+ InProgress-
Capabilities: [520 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [950 v1] Vendor Specific Information: ID=0001 Rev=0 Len=010 <?>
Kernel driver in use: pcieport
...........
05:00.0 System peripheral: Altera Corporation Device 0005 (rev 01)
Subsystem: Altera Corporation Device 0005
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 20200000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [50] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [200 v1] Vendor Specific Information: ID=1172 Rev=0 Len=044 <?>
内存映射：
root@am57xx-evm:~# cat /proc/iomem
20013000-2fffffff : MEM
20100000-201fffff : 0000:00:00.0
20200000-204fffff : PCI Bus 0000:01
20200000-203fffff : PCI Bus 0000:02
20200000-202fffff : PCI Bus 0000:05
20200000-2027ffff : 0000:05:00.0
20300000-203fffff : PCI Bus 0000:09
20300000-2031ffff : 0000:09:00.0
20320000-2033ffff : 0000:09:00.1
20400000-2041ffff : 0000:01:00.0
20420000-2043ffff : 0000:01:00.1
40300000-4037ffff : 40300000.ocmcram
40500000-405fffff : CMEM
40800000-40847fff : l2ram
40d01000-40d010ff : /ocp/mmu@40d01000
40d02000-40d020ff : /ocp/mmu@40d02000
40e00000-40e07fff : l1pram
40f00000-40f07fff : l1dram
41000000-41047fff : l2ram
41501000-415010ff : /ocp/mmu@41501000
41502000-415020ff : /ocp/mmu@41502000
41600000-41607fff : l1pram
41700000-41707fff : l1dram
43300000-433fffff : edma3_cc
44000000-44ffffff : /ocp
45000000-45000fff : /ocp
48020000-4802001f : serial
48032000-4803207f : /ocp/timer@48032000
48034000-4803407f : /ocp/timer@48034000
48036000-4803607f : /ocp/timer@48036000
4803e000-4803e07f : /ocp/timer@4803e000
48051000-480511ff : /ocp/gpio@48051000
48053000-480531ff : /ocp/gpio@48053000
48055000-480551ff : /ocp/gpio@48055000
48057000-480571ff : /ocp/gpio@48057000
48059000-480591ff : /ocp/gpio@48059000
4805b000-4805b1ff : /ocp/gpio@4805b000
4805d000-4805d1ff : /ocp/gpio@4805d000
48060000-480600ff : /ocp/i2c@48060000
48070000-480700ff : /ocp/i2c@48070000
4807c000-4807c0ff : /ocp/i2c@4807c000
48086000-4808607f : /ocp/timer@48086000
48088000-4808807f : /ocp/timer@48088000
48090000-48091fff : /ocp/rng@48090000
4809c000-4809c3ff : /ocp/mmc@4809c000
480a5000-480a509f : /ocp/des@480a5000
48422000-4842201f : serial
48440200-4844027f : /ocp/epwmss@48440000/pwm@48440200
4844a000-4844ad1b : /ocp/padconf@4844a000
48484000-48484fff : /ocp/ethernet@48484000
48485000-484850ff : /ocp/ethernet@48484000/mdio@48485000
48485200-48487fff : /ocp/ethernet@48484000
48820000-4882007f : /ocp/timer@48820000
48822000-4882207f : /ocp/timer@48822000
48824000-4882407f : /ocp/timer@48824000
48826000-4882607f : /ocp/timer@48826000
48828000-4882807f : /ocp/timer@48828000
4882a000-4882a07f : /ocp/timer@4882a000
4882c000-4882c07f : /ocp/timer@4882c000
4882e000-4882e07f : /ocp/timer@4882e000
48838000-488380ff : /ocp/rtc@48838000
48840000-488401ff : /ocp/mailbox@48840000
48842000-488421ff : /ocp/mailbox@48842000
48880000-4888ffff : /ocp/omap_dwc3_1@48880000
48890000-48897fff : /ocp/omap_dwc3_1@48880000/usb@48890000
48890000-48897fff : /ocp/omap_dwc3_1@48880000/usb@48890000
4889c100-488a6fff : /ocp/omap_dwc3_1@48880000/usb@48890000
488c0000-488cffff : /ocp/omap_dwc3_2@488c0000
488d0000-488d7fff : /ocp/omap_dwc3_2@488c0000/usb@488d0000
488d0000-488d7fff : /ocp/omap_dwc3_2@488c0000/usb@488d0000
488dc100-488e6fff : /ocp/omap_dwc3_2@488c0000/usb@488d0000
489d0700-489d077f : sc
489d5700-489d5717 : csc
4a0021e0-4a0021eb : /ocp/bandgap@4a0021e0
4a00232c-4a002337 : /ocp/bandgap@4a0021e0
4a002380-4a0023ab : /ocp/bandgap@4a0021e0
4a0023c0-4a0023fb : /ocp/bandgap@4a0021e0
4a00246c-4a00246f : ldo-address
4a002470-4a002473 : ldo-address
4a002554-4a002557 : gmii-sel
4a002564-4a00256b : /ocp/bandgap@4a0021e0
4a002574-4a0025c3 : /ocp/bandgap@4a0021e0
4a002b78-4a002c73 : /ocp/l4@4a000000/scm@2000/dma-router@b78
4a002c78-4a002cf3 : /ocp/l4@4a000000/scm@2000/dma-router@c78
4a003400-4a003867 : pinctrl-single
4a056000-4a056fff : omap_dma_system.0
4a056000-4a056fff : /ocp/dma-controller@4a056000
4a080000-4a08001f : /ocp/ocp2scp@4a080000
4a084000-4a0843ff : /ocp/ocp2scp@4a080000/phy@4a084000
4a084c00-4a084c3f : pll_ctrl
4a085000-4a0853ff : /ocp/ocp2scp@4a080000/phy@4a085000
4a090000-4a09001f : /ocp/ocp2scp@4a090000
4a094000-4a09407f : phy_rx
4a094400-4a094463 : phy_tx
4a096800-4a09683f : pll_ctrl
4a140000-4a1410ff : /ocp/sata@4a141100
4ae07ddc-4ae07ddf : setup-address
4ae07de0-4ae07de3 : control-address
4ae07de4-4ae07de7 : setup-address
4ae07de8-4ae07deb : control-address
4ae07e20-4ae07e23 : control-address
4ae07e24-4ae07e27 : control-address
4ae07e30-4ae07e33 : setup-address
4ae07e34-4ae07e37 : setup-address
4ae0c154-4ae0c157 : ldo-address
4ae0c158-4ae0c15b : ldo-address
4ae10000-4ae101ff : /ocp/gpio@4ae10000
4ae14000-4ae1407f : /ocp/wdt@4ae14000
4ae20000-4ae2007f : /ocp/timer@4ae20000
4b101000-4b1012ff : /ocp/sham@53100000
4b220000-4b221fff : intc
4b222000-4b2223ff : control
4b222400-4b2224ff : debug
4b224000-4b2243ff : control
4b224400-4b2244ff : debug
4b234000-4b236fff : iram
4b238000-4b23afff : iram
4b2a0000-4b2a1fff : intc
4b2a2000-4b2a23ff : control
4b2a2400-4b2a24ff : debug
4b2a4000-4b2a43ff : control
4b2a4400-4b2a44ff : debug
4b2b4000-4b2b6fff : iram
4b2b8000-4b2bafff : iram
4b500000-4b50009f : /ocp/aes@4b500000
4b700000-4b70009f : /ocp/aes@4b700000
55020000-5502ffff : l2ram
55082000-550820ff : /ocp/mmu@55082000
58000000-5800007f : dss
58001000-58001fff : /ocp/dss@58000000/dispc@58001000
58004054-58004057 : pll1_clkctrl
58004300-5800431f : pll1
58009054-58009057 : pll2_clkctrl
58009300-5800931f : pll2
58040000-580401ff : wp
58040200-5804027f : pll
58040300-5804037f : phy
58060000-58078fff : core
58820000-5882ffff : l2ram
58882000-588820ff : /ocp/mmu@58882000
80000000-9fffffff : System RAM
80008000-80dfffff : Kernel code
81000000-8109ebdf : Kernel data
a0000000-abffffff : CMEM
ac000000-ffcfffff : System RAM
我的引导日志：
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.79-gbde58ab01e (khrenkov@khrenkov-sitar) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #6 SMP PREEMPT Thu Dec 23 12:04:11 +07 2021
[ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: TI AM5728 EVM
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000009f000000, size 8 MiB
[ 0.000000] OF: reserved mem: initialized node dsp2-memory@9f000000, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 24 MiB at 0x00000000fe400000
[ 0.000000] OMAP4: Map 0x00000000ffd00000 to fe600000 for dram barrier
[ 0.000000] On node 0 totalpages: 474368
[ 0.000000] free_area_init_node: node 0, pgdat c1053d80, node_mem_map eeda2000
[ 0.000000] DMA zone: 1728 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 147456 pages, LIFO batch:31
[ 0.000000] HighMem zone: 326912 pages, LIFO batch:31
[ 0.000000] DRA752 ES2.0
[ 0.000000] percpu: Embedded 15 pages/cpu @eed2a000 s31372 r8192 d21876 u61440
[ 0.000000] pcpu-alloc: s31372 r8192 d21876 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 472640
[ 0.000000] Kernel command line: console=ttyO2,115200n8 root=/dev/nfs nfsroot=192.168.9.168:/home/khrenkov/Sitara/SDK/customNFS,nolock,v3,tcp,rsize=4096,wsize=4096 rw ip=dhcp
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1675580K/1897472K available (8192K kernel code, 347K rwdata, 2564K rodata, 2048K init, 282K bss, 33476K reserved, 188416K cma-reserved, 1283072K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB)
[ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB)
[ 0.000000] .data : 0xc1000000 - 0xc1056e98 ( 348 kB)
[ 0.000000] .bss : 0xc1058000 - 0xc109ebe0 ( 283 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] OMAP clockevent source: timer1 at 32786 Hz
[ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[ 0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[ 0.000016] Switching to timer-based delay loop, resolution 162ns
[ 0.000362] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[ 0.000371] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.000894] Console: colour dummy device 80x30
[ 0.000912] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
[ 0.000919] This ensures that you still see kernel messages. Please
[ 0.000926] update your kernel commandline.
[ 0.000948] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[ 0.000962] pid_max: default: 32768 minimum: 301
[ 0.001081] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001095] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001627] CPU: Testing write buffer coherency: ok
[ 0.001664] CPU0: Spectre v2: using ICIALLU workaround
[ 0.001859] /cpus/cpu@0 missing clock-frequency property
[ 0.001879] /cpus/cpu@1 missing clock-frequency property
[ 0.001890] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.039846] Setting up static identity map for 0x80200000 - 0x80200060
[ 0.059859] Hierarchical SRCU implementation.
[ 0.080045] EFI services will not be available.
[ 0.099913] smp: Bringing up secondary CPUs ...
[ 0.170289] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.170294] CPU1: Spectre v2: using ICIALLU workaround
[ 0.170395] smp: Brought up 1 node, 2 CPUs
[ 0.170406] SMP: Total of 2 processors activated (24.59 BogoMIPS).
[ 0.170414] CPU: All CPU(s) started in HYP mode.
[ 0.170421] CPU: Virtualization extensions available.
[ 0.170960] devtmpfs: initialized
[ 0.191448] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[ 0.191701] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 0.191897] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.191912] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.195659] pinctrl core: initialized pinctrl subsystem
[ 0.196118] DMI not present or invalid.
[ 0.196371] NET: Registered protocol family 16
[ 0.197415] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.198355] omap_hwmod: l3_main_2 using broken dt data from ocp
[ 0.307851] omap_hwmod: dcan1: _wait_target_disable failed
[ 0.419754] cpuidle: using governor ladder
[ 0.419786] cpuidle: using governor menu
[ 0.428244] gpio gpiochip0: (gpio): added GPIO chardev (254:0)
[ 0.428313] gpiochip_setup_dev: registered GPIOs 0 to 31 on device: gpiochip0 (gpio)
[ 0.428373] OMAP GPIO hardware version 0.1
[ 0.429011] gpio gpiochip1: (gpio): added GPIO chardev (254:1)
[ 0.429078] gpiochip_setup_dev: registered GPIOs 32 to 63 on device: gpiochip1 (gpio)
[ 0.429748] gpio gpiochip2: (gpio): added GPIO chardev (254:2)
[ 0.429814] gpiochip_setup_dev: registered GPIOs 64 to 95 on device: gpiochip2 (gpio)
[ 0.430524] gpio gpiochip3: (gpio): added GPIO chardev (254:3)
[ 0.430594] gpiochip_setup_dev: registered GPIOs 96 to 127 on device: gpiochip3 (gpio)
[ 0.431259] gpio gpiochip4: (gpio): added GPIO chardev (254:4)
[ 0.431325] gpiochip_setup_dev: registered GPIOs 128 to 159 on device: gpiochip4 (gpio)
[ 0.432000] gpio gpiochip5: (gpio): added GPIO chardev (254:5)
[ 0.432065] gpiochip_setup_dev: registered GPIOs 160 to 191 on device: gpiochip5 (gpio)
[ 0.432717] gpio gpiochip6: (gpio): added GPIO chardev (254:6)
[ 0.432784] gpiochip_setup_dev: registered GPIOs 192 to 223 on device: gpiochip6 (gpio)
[ 0.433460] gpio gpiochip7: (gpio): added GPIO chardev (254:7)
[ 0.433525] gpiochip_setup_dev: registered GPIOs 224 to 255 on device: gpiochip7 (gpio)
[ 0.455805] No ATAGs?
[ 0.455879] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.455893] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.456284] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[ 0.456295] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[ 0.456834] OMAP DMA hardware revision 0.0
[ 0.466750] edma 43300000.edma: memcpy is disabled
[ 0.469983] edma 43300000.edma: TI EDMA DMA engine driver
[ 0.476801] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[ 0.477175] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixedregulator-mmcwl[0]' - status (0)
[ 0.477430] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-com_3v6[0]'
[ 0.477840] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-main_12v0[0]'
[ 0.478069] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-evm_5v0[0]'
[ 0.478119] evm_5v0: supplied by main_12v0
[ 0.478373] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-vdd_3v3[0]'
[ 0.478521] com_3v6: supplied by evm_5v0
[ 0.478644] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-aic_dvdd[0]'
[ 0.478694] aic_dvdd_fixed: supplied by vdd_3v3
[ 0.478932] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixedregulator-vtt[0]' - status (0)
[ 0.481400] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[ 0.481593] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[ 0.481831] omap-iommu 58882000.mmu: 58882000.mmu registered
[ 0.482078] omap-iommu 55082000.mmu: 55082000.mmu registered
[ 0.482421] omap-iommu 41501000.mmu: 41501000.mmu registered
[ 0.482627] omap-iommu 41502000.mmu: 41502000.mmu registered
[ 0.482888] iommu: Adding device 58820000.ipu to group 1
[ 0.482976] iommu: Adding device 55020000.ipu to group 2
[ 0.483134] iommu: Adding device 40800000.dsp to group 0
[ 0.483393] iommu: Adding device 41000000.dsp to group 3
[ 0.485650] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[ 0.486151] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[ 0.486636] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[ 0.486804] media: Linux media interface: v0.10
[ 0.486841] Linux video capture interface: v2.00
[ 0.486918] pps_core: LinuxPPS API ver. 1 registered
[ 0.486927] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.486947] PTP clock support registered
[ 0.486975] EDAC MC: Ver: 3.0.0
[ 0.487223] dmi: Firmware registration failed.
[ 0.487611] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[ 0.487881] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[ 0.488201] Advanced Linux Sound Architecture Driver Initialized.
[ 0.488908] clocksource: Switched to clocksource arch_sys_counter
[ 0.496604] NET: Registered protocol family 2
[ 0.497116] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.497180] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.497306] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.497374] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.497407] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.497533] NET: Registered protocol family 1
[ 0.497818] RPC: Registered named UNIX socket transport module.
[ 0.497827] RPC: Registered udp transport module.
[ 0.497835] RPC: Registered tcp transport module.
[ 0.497843] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.497855] PCI: CLS 0 bytes, default 64
[ 0.498748] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[ 0.498966] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[ 0.499951] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 0.504174] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.504685] NFS: Registering the id_resolver key type
[ 0.504708] Key type id_resolver registered
[ 0.504717] Key type id_legacy registered
[ 0.504754] ntfs: driver 2.1.32 [Flags: R/O].
[ 0.506074] bounce: pool size: 64 pages
[ 0.506118] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 0.506129] io scheduler noop registered
[ 0.506138] io scheduler deadline registered
[ 0.506238] io scheduler cfq registered (default)
[ 0.506247] io scheduler mq-deadline registered
[ 0.506256] io scheduler kyber registered
[ 0.510548] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[ 0.513737] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1
[ 0.513896] dra7-pcie 51000000.pcie: GPIO lookup for consumer (null)
[ 0.513908] dra7-pcie 51000000.pcie: using device tree for GPIO lookup
[ 0.513943] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ocp/axi@0/pcie@51000000[0]' - status (0)
[ 0.514106] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges:
[ 0.514140] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000
[ 0.514162] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000
[ 0.614247] dra7-pcie 51000000.pcie: link up
[ 0.614384] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00
[ 0.614397] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.614408] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.614418] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff]
[ 0.614452] pci 0000:00:00.0: [104c:8888] type 01 class 0x060400
[ 0.614485] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 0.614545] pci 0000:00:00.0: supports D1
[ 0.614555] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.614738] PCI: bus0: Fast back to back transfers disabled
[ 0.614890] pci 0000:01:00.0: [10b5:8609] type 01 class 0x060400
[ 0.615034] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0001ffff]
[ 0.615476] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.615750] pci 0000:01:00.1: [10b5:8609] type 00 class 0x088000
[ 0.615866] pci 0000:01:00.1: reg 0x10: [mem 0x00000000-0x0001ffff]
[ 0.616061] pci 0000:01:00.1: enabling Extended Tags
[ 0.639070] PCI: bus1: Fast back to back transfers disabled
[ 0.639089] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.639386] pci 0000:02:01.0: [10b5:8609] type 01 class 0x060400
[ 0.639930] pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
[ 0.640224] pci 0000:02:04.0: [10b5:8609] type 01 class 0x060400
[ 0.640768] pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
[ 0.641053] pci 0000:02:05.0: [10b5:8609] type 01 class 0x060400
[ 0.641596] pci 0000:02:05.0: PME# supported from D0 D3hot D3cold
[ 0.641885] pci 0000:02:06.0: [10b5:8609] type 01 class 0x060400
[ 0.642429] pci 0000:02:06.0: PME# supported from D0 D3hot D3cold
[ 0.642724] pci 0000:02:07.0: [10b5:8609] type 01 class 0x060400
[ 0.643267] pci 0000:02:07.0: PME# supported from D0 D3hot D3cold
[ 0.643568] pci 0000:02:08.0: [10b5:8609] type 01 class 0x060400
[ 0.644113] pci 0000:02:08.0: PME# supported from D0 D3hot D3cold
[ 0.644419] pci 0000:02:09.0: [10b5:8609] type 01 class 0x060400
[ 0.644964] pci 0000:02:09.0: PME# supported from D0 D3hot D3cold
[ 0.645551] PCI: bus2: Fast back to back transfers disabled
[ 0.645569] pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.645606] pci 0000:02:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.645642] pci 0000:02:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.645678] pci 0000:02:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.645714] pci 0000:02:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.645750] pci 0000:02:08.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.645785] pci 0000:02:09.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.646014] PCI: bus3: Fast back to back transfers enabled
[ 0.646027] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03
[ 0.646245] PCI: bus4: Fast back to back transfers enabled
[ 0.646257] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 04
[ 0.646549] pci 0000:05:00.0: [1172:0005] type 00 class 0x088000
[ 0.646687] pci 0000:05:00.0: reg 0x10: [mem 0x00000000-0x0007ffff]
[ 0.647519] PCI: bus5: Fast back to back transfers disabled
[ 0.647532] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05
[ 0.647752] PCI: bus6: Fast back to back transfers enabled
[ 0.647764] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
[ 0.647986] PCI: bus7: Fast back to back transfers enabled
[ 0.647998] pci_bus 0000:07: busn_res: [bus 07-ff] end is updated to 07
[ 0.648220] PCI: bus8: Fast back to back transfers enabled
[ 0.648232] pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 08
[ 0.648510] pci 0000:09:00.0: [10b5:8609] type 01 class 0x060400
[ 0.648660] pci 0000:09:00.0: reg 0x10: [mem 0x00000000-0x0001ffff]
[ 0.649158] pci 0000:09:00.0: PME# supported from D0 D3hot D3cold
[ 0.649496] pci 0000:09:00.1: [10b5:8609] type 00 class 0x088000
[ 0.649617] pci 0000:09:00.1: reg 0x10: [mem 0x00000000-0x0001ffff]
[ 0.649827] pci 0000:09:00.1: enabling Extended Tags
[ 0.650618] PCI: bus9: Fast back to back transfers disabled
[ 0.650635] pci 0000:09:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.650944] pci 0000:0a:01.0: [10b5:8609] type 01 class 0x060400
[ 0.651525] pci 0000:0a:01.0: PME# supported from D0 D3hot D3cold
[ 0.651827] pci 0000:0a:04.0: [10b5:8609] type 01 class 0x060400
[ 0.652405] pci 0000:0a:04.0: PME# supported from D0 D3hot D3cold
[ 0.652701] pci 0000:0a:05.0: [10b5:8609] type 01 class 0x060400
[ 0.653283] pci 0000:0a:05.0: PME# supported from D0 D3hot D3cold
[ 0.653585] pci 0000:0a:06.0: [10b5:8609] type 01 class 0x060400
[ 0.654164] pci 0000:0a:06.0: PME# supported from D0 D3hot D3cold
[ 0.654471] pci 0000:0a:07.0: [10b5:8609] type 01 class 0x060400
[ 0.655052] pci 0000:0a:07.0: PME# supported from D0 D3hot D3cold
[ 0.655362] pci 0000:0a:08.0: [10b5:8609] type 01 class 0x060400
[ 0.655940] pci 0000:0a:08.0: PME# supported from D0 D3hot D3cold
[ 0.656258] pci 0000:0a:09.0: [10b5:8609] type 01 class 0x060400
[ 0.656838] pci 0000:0a:09.0: PME# supported from D0 D3hot D3cold
[ 0.657451] PCI: bus10: Fast back to back transfers disabled
[ 0.657470] pci 0000:0a:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657508] pci 0000:0a:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657545] pci 0000:0a:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657583] pci 0000:0a:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657619] pci 0000:0a:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657656] pci 0000:0a:08.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657692] pci 0000:0a:09.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.657933] PCI: bus11: Fast back to back transfers enabled
[ 0.657945] pci_bus 0000:0b: busn_res: [bus 0b-ff] end is updated to 0b
[ 0.658182] PCI: bus12: Fast back to back transfers enabled
[ 0.658194] pci_bus 0000:0c: busn_res: [bus 0c-ff] end is updated to 0c
[ 0.658425] PCI: bus13: Fast back to back transfers enabled
[ 0.658436] pci_bus 0000:0d: busn_res: [bus 0d-ff] end is updated to 0d
[ 0.658667] PCI: bus14: Fast back to back transfers enabled
[ 0.658678] pci_bus 0000:0e: busn_res: [bus 0e-ff] end is updated to 0e
[ 0.658933] PCI: bus15: Fast back to back transfers enabled
[ 0.658945] pci_bus 0000:0f: busn_res: [bus 0f-ff] end is updated to 0f
[ 0.659178] PCI: bus16: Fast back to back transfers enabled
[ 0.659190] pci_bus 0000:10: busn_res: [bus 10-ff] end is updated to 10
[ 0.659422] PCI: bus17: Fast back to back transfers enabled
[ 0.659434] pci_bus 0000:11: busn_res: [bus 11-ff] end is updated to 11
[ 0.659457] pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 11
[ 0.659478] pci_bus 0000:09: busn_res: [bus 09-ff] end is updated to 11
[ 0.659500] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 11
[ 0.660088] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit]
[ 0.660107] pci 0000:00:00.0: BAR 8: assigned [mem 0x20200000-0x204fffff]
[ 0.660122] pci 0000:01:00.0: BAR 8: assigned [mem 0x20200000-0x203fffff]
[ 0.660134] pci 0000:01:00.0: BAR 0: assigned [mem 0x20400000-0x2041ffff]
[ 0.660156] pci 0000:01:00.1: BAR 0: assigned [mem 0x20420000-0x2043ffff]
[ 0.660181] pci 0000:02:05.0: BAR 8: assigned [mem 0x20200000-0x202fffff]
[ 0.660192] pci 0000:02:09.0: BAR 8: assigned [mem 0x20300000-0x203fffff]
[ 0.660203] pci 0000:02:01.0: PCI bridge to [bus 03]
[ 0.660258] pci 0000:02:04.0: PCI bridge to [bus 04]
[ 0.660314] pci 0000:05:00.0: BAR 0: assigned [mem 0x20200000-0x2027ffff]
[ 0.660336] pci 0000:02:05.0: PCI bridge to [bus 05]
[ 0.660361] pci 0000:02:05.0: bridge window [mem 0x20200000-0x202fffff]
[ 0.660400] pci 0000:02:06.0: PCI bridge to [bus 06]
[ 0.660453] pci 0000:02:07.0: PCI bridge to [bus 07]
[ 0.660506] pci 0000:02:08.0: PCI bridge to [bus 08]
[ 0.660562] pci 0000:09:00.0: BAR 0: assigned [mem 0x20300000-0x2031ffff]
[ 0.660583] pci 0000:09:00.1: BAR 0: assigned [mem 0x20320000-0x2033ffff]
[ 0.660606] pci 0000:0a:01.0: PCI bridge to [bus 0b]
[ 0.660659] pci 0000:0a:04.0: PCI bridge to [bus 0c]
[ 0.660712] pci 0000:0a:05.0: PCI bridge to [bus 0d]
[ 0.660765] pci 0000:0a:06.0: PCI bridge to [bus 0e]
[ 0.660818] pci 0000:0a:07.0: PCI bridge to [bus 0f]
[ 0.660871] pci 0000:0a:08.0: PCI bridge to [bus 10]
[ 0.660924] pci 0000:0a:09.0: PCI bridge to [bus 11]
[ 0.660977] pci 0000:09:00.0: PCI bridge to [bus 0a-11]
[ 0.661030] pci 0000:02:09.0: PCI bridge to [bus 09-11]
[ 0.661054] pci 0000:02:09.0: bridge window [mem 0x20300000-0x203fffff]
[ 0.661092] pci 0000:01:00.0: PCI bridge to [bus 02-11]
[ 0.661117] pci 0000:01:00.0: bridge window [mem 0x20200000-0x203fffff]
[ 0.661155] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.661167] pci 0000:00:00.0: bridge window [mem 0x20200000-0x204fffff]
[ 0.661497] pcieport 0000:00:00.0: Signaling PME with IRQ 167
[ 0.661858] pcieport 0000:00:00.0: AER enabled with IRQ 167
[ 0.662044] pcieport 0000:01:00.0: enabling device (0140 -> 0142)
[ 0.665361] pcieport 0000:02:05.0: enabling device (0140 -> 0142)
[ 0.669796] pcieport 0000:02:09.0: enabling device (0140 -> 0142)
[ 0.670922] pcieport 0000:09:00.0: enabling device (0140 -> 0142)
[ 0.680573] pwm-backlight backlight: GPIO lookup for consumer enable
[ 0.680585] pwm-backlight backlight: using device tree for GPIO lookup
[ 0.680598] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/backlight[0]'
[ 0.680610] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/backlight[0]'
[ 0.680619] pwm-backlight backlight: using lookup tables for GPIO lookup
[ 0.680629] pwm-backlight backlight: lookup for GPIO enable failed
[ 0.680651] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[ 0.725461] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.728182] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 45, base_baud = 3000000) is a 8250
[ 2.821555] console [ttyS2] enabled
[ 2.825883] 48422000.serial: ttyS7 at MMIO 0x48422000 (irq = 46, base_baud = 3000000) is a 8250
[ 2.836512] omap_rng 48090000.rng: Random Number Generator ver. 20
[ 2.843232] omapdss_dss 58000000.dss: 58000000.dss supply vdda_video not found, using dummy regulator
[ 2.852724] DSS: OMAP DSS rev 6.1
[ 2.857681] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
[ 2.866106] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops)
[ 2.875092] tpd12s015 encoder: GPIO lookup for consumer (null)
[ 2.880975] tpd12s015 encoder: using device tree for GPIO lookup
[ 2.887037] of_get_named_gpiod_flags: parsed 'gpios' property of node '/encoder[0]' - status (0)
[ 2.895886] tpd12s015 encoder: GPIO lookup for consumer (null)
[ 2.901762] tpd12s015 encoder: using device tree for GPIO lookup
[ 2.907829] of_get_named_gpiod_flags: parsed 'gpios' property of node '/encoder[1]' - status (0)
[ 2.916674] tpd12s015 encoder: GPIO lookup for consumer (null)
[ 2.922549] tpd12s015 encoder: using device tree for GPIO lookup
[ 2.928628] of_get_named_gpiod_flags: parsed 'gpios' property of node '/encoder[2]' - status (0)
[ 2.938296] of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/connector[0]'
[ 2.957139] brd: module loaded
[ 2.965658] loop: module loaded
[ 2.971734] mdio_bus fixed-0: GPIO lookup for consumer reset
[ 2.977420] mdio_bus fixed-0: using lookup tables for GPIO lookup
[ 2.983566] mdio_bus fixed-0: lookup for GPIO reset failed
[ 2.989126] libphy: Fixed MDIO Bus: probed
[ 2.995824] mdio_bus 48485000.mdio: GPIO lookup for consumer reset
[ 3.002059] mdio_bus 48485000.mdio: using device tree for GPIO lookup
[ 3.008535] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/ethernet@48484000/mdio@48485000[0]'
[ 3.019650] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/ethernet@48484000/mdio@48485000[0]'
[ 3.030670] mdio_bus 48485000.mdio: using lookup tables for GPIO lookup
[ 3.037315] mdio_bus 48485000.mdio: lookup for GPIO reset failed
[ 3.098938] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000
[ 3.106632] libphy: 48485000.mdio: probed
[ 3.115804] davinci_mdio 48485000.mdio: phy[0]: device 48485000.mdio:00, driver Micrel KSZ9031 Gigabit PHY
[ 3.125548] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver Micrel KSZ9031 Gigabit PHY
[ 3.135856] cpsw 48484000.ethernet: Detected MACID = b0:7e:11:52:23:5f
[ 3.142491] cpsw 48484000.ethernet: initialized cpsw ale version 1.4
[ 3.148873] cpsw 48484000.ethernet: ALE Table size 1024
[ 3.154172] cpsw 48484000.ethernet: device node lookup for pps timer failed
[ 3.161220] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies)
[ 3.169118] cpsw 48484000.ethernet: cpsw: Detected MACID = b0:7e:11:52:23:5f
[ 3.177313] i2c /dev entries driver
[ 3.181723] IR NEC protocol handler initialized
[ 3.186276] IR RC5(x/sz) protocol handler initialized
[ 3.191374] IR RC6 protocol handler initialized
[ 3.195925] IR JVC protocol handler initialized
[ 3.200492] IR Sony protocol handler initialized
[ 3.205129] IR SANYO protocol handler initialized
[ 3.209992] IR Sharp protocol handler initialized
[ 3.214715] IR MCE Keyboard/mouse protocol handler initialized
[ 3.220589] IR XMP protocol handler initialized
[ 3.249005] tmp102 0-0048: error reading config register
[ 3.254471] tmp102: probe of 0-0048 failed with error -121
[ 3.262882] sdhci: Secure Digital Host Controller Interface driver
[ 3.269116] sdhci: Copyright(c) Pierre Ossman
[ 3.274019] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.280757] sdhci-omap 4809c000.mmc: GPIO lookup for consumer cd
[ 3.286794] sdhci-omap 4809c000.mmc: using device tree for GPIO lookup
[ 3.293386] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]'
[ 3.302581] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]'
[ 3.311685] sdhci-omap 4809c000.mmc: using lookup tables for GPIO lookup
[ 3.318418] sdhci-omap 4809c000.mmc: lookup for GPIO cd failed
[ 3.324295] sdhci-omap 4809c000.mmc: GPIO lookup for consumer wp
[ 3.330341] sdhci-omap 4809c000.mmc: using device tree for GPIO lookup
[ 3.336899] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]'
[ 3.346089] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]'
[ 3.355187] sdhci-omap 4809c000.mmc: using lookup tables for GPIO lookup
[ 3.361933] sdhci-omap 4809c000.mmc: lookup for GPIO wp failed
[ 3.367944] sdhci-omap 4809c000.mmc: 4809c000.mmc supply vqmmc not found, using dummy regulator
[ 3.377023] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode
[ 3.438964] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[ 3.447634] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led0[0]' - status (0)
[ 3.458707] no flags found for gpios
[ 3.462442] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led1[0]' - status (0)
[ 3.471553] no flags found for gpios
[ 3.475331] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led2[0]' - status (0)
[ 3.484440] no flags found for gpios
[ 3.488232] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led3[0]' - status (0)
[ 3.497284] no flags found for gpios
[ 3.502027] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led4[0]' - status (0)
[ 3.513093] no flags found for gpios
[ 3.516804] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led5[0]' - status (0)
[ 3.525854] no flags found for gpios
[ 3.529962] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.539790] NET: Registered protocol family 10
[ 3.545078] Segment Routing with IPv6
[ 3.548808] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.555218] NET: Registered protocol family 17
[ 3.559910] Key type dns_resolver registered
[ 3.564346] omap_voltage_late_init: Voltage driver support not added
[ 3.570782] Power Management for TI OMAP4+ devices.
[ 3.576985] Registering SWP/SWPB emulation handler
[ 3.595129] dmm 4e000000.dmm: workaround for errata i878 in use
[ 3.602726] dmm 4e000000.dmm: initialized all PAT entries
[ 3.608585] omapdss_hdmi5 58040000.encoder: 58040000.encoder supply vdda not found, using dummy regulator
[ 3.619855] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.626500] [drm] No driver support for vblank timestamp query.
[ 3.632514] [drm] Cannot find any crtc or sizes
[ 3.638141] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0
[ 3.646404] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio_keys/USER5[0]' - status (0)
[ 3.656080] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio_keys/USER4[0]' - status (0)
[ 3.665721] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio_keys/USER3[0]' - status (0)
[ 3.675366] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio_keys/USER2[0]' - status (0)
[ 3.685009] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio_keys/USER1[0]' - status (0)
[ 3.694751] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 3.702396] hctosys: unable to open rtc device (rtc0)
[ 3.708625] net eth0: initializing cpsw version 1.15 (0)
[ 3.716128] mmc0: host does not support reading read-only switch, assuming write-enable
[ 3.726127] mmc0: new high speed SDHC card at address 0001
[ 3.731969] mmcblk0: mmc0:0001 SD32G 29.1 GiB
[ 3.737351] mmcblk0: p1 p2
[ 3.839706] Micrel KSZ9031 Gigabit PHY 48485000.mdio:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[ 3.860333] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.866731] net eth1: initializing cpsw version 1.15 (0)
[ 3.989385] Micrel KSZ9031 Gigabit PHY 48485000.mdio:02: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:02, irq=POLL)
[ 4.008209] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 4.648955] [drm] Cannot find any crtc or sizes
[ 8.177597] cpsw 48484000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.185508] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 8.208931] Sending DHCP requests ., OK
[ 8.252813] IP-Config: Got DHCP answer from 192.168.8.1, my address is 192.168.8.167
[ 8.260629] IP-Config: Complete:
[ 8.263876] device=eth1, hwaddr=b0:7e:11:52:23:5f, ipaddr=192.168.8.167, mask=255.255.252.0, gw=192.168.8.17
[ 8.274207] host=192.168.8.167, domain=tetz, nis-domain=(none)
[ 8.281030] bootserver=0.0.0.0, rootserver=192.168.9.168, rootpath= nameserver0=192.168.8.1
[ 8.296513] vmmcwl_fixed: disabling
[ 8.300049] aic_dvdd_fixed: disabling
[ 8.303735] ALSA device list:
[ 8.306716] No soundcards found.
[ 8.338962] VFS: Mounted root (nfs filesystem) on device 0:15.
[ 8.346076] devtmpfs: mounted
[ 8.350327] Freeing unused kernel memory: 2048K
[ 8.374241] random: fast init done
[ 8.816851] systemd[1]: System time before build time, advancing clock.
[ 8.884912] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN default-hierarchy=hybrid)
[ 8.906249] systemd[1]: Detected architecture arm.
Welcome to Arago 2018.10!
[ 8.951903] systemd[1]: Set hostname to <am57xx-evm>.
[ 10.093335] random: systemd: uninitialized urandom read (16 bytes read)
[ 10.138311] systemd[1]: Listening on Process Core Dump Socket.
[ OK ] Listening on Process Core Dump Socket.
[ 10.169042] random: systemd: uninitialized urandom read (16 bytes read)
[ 10.175722] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 10.209009] random: systemd: uninitialized urandom read (16 bytes read)
[ 10.217478] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 10.322255] random: crng init done
[ 10.334095] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 10.369976] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 10.409093] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 10.441877] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Reached target Swap.
Mounting Temporary Directory (/tmp)...
[ OK ] Created slice system-getty.slice.
[ OK ] Listening on Journal Socket.
Starting Remount Root and Kernel File Systems...
Starting Create list of required st…ce nodes for the current kernel...
Starting Load Kernel Modules...
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Created slice system-serial\x2dgetty.slice.
Mounting Kernel Debug File System...
[ 10.927142] cmemk: loading out-of-tree module taints kernel.
[ 10.933854] CMEMK module: reference Linux version 4.14.79
[ 10.940136] allocated heap buffer 0x40500000 of size 0x100000
[ 10.946066] cmemk initialized
[ OK ] Started Dispatch Password Requests to Console[ 10.964817] cryptodev: driver 1.9 loaded.
Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Listening on Syslog Socket.
Starting Journal Service...
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Temporary Directory (/tmp).
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started Create list of required sta…vice nodes for the current kernel.
[ OK ] Started Load Kernel Modules.
Starting Apply Kernel Variables...
Mounting Kernel Configuration File System...
Starting Create Static Device Nodes in /dev...
Starting udev Coldplug all Devices...
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started Journal Service.
[ OK ] Started Apply Kernel Variables.
Starting Flush Journal to Persistent Storage...
[ 11.595669] systemd-journald[85]: Received request to flush runtime journal from PID 1
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
Mounting /media/ram...
Mounting /var/volatile...
[ OK ] Mounted /var/volatile.
[ OK ] Mounted /media/ram.
[ OK ] Started Flush Journal to Persistent Storage.
Starting Load/Save Random Seed...
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
Starting Network Time Synchronization...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Synchronized.
[ 12.560835] omap-rproc 58820000.ipu: assigned reserved memory node ipu1-memory@9d000000
[ OK ] Started udev Coldplug all Devices.
[ 12.605843] remoteproc remoteproc0: 58820000.ipu is available
[ OK ] Reached target System Initialization.
[ 12.637577] omap-rproc 55020000.ipu: assigned reserved memory node ipu2-memory@95800000
[ 12.654757] remoteproc remoteproc1: 55020000.ipu is available
[ 12.671388] omap-rproc 40800000.dsp: assigned reserved memory node dsp1-memory@99000000
[ 12.707444] remoteproc remoteproc2: 40800000.dsp is available
[ 12.730586] omap-rproc 41000000.dsp: assigned reserved memory node dsp2-memory@9f000000
[ 12.741730] remoteproc remoteproc3: 41000000.dsp is available
[ OK ] Listening on dropbear.socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
Starting Network Service...
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Started Daily rotation of log files.
[ OK ] Reached target Timers.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting TI MultiCore Tools Daemon...
Starting System Logging Service...
[ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf.
[ 14.402230] remoteproc remoteproc1: powering up 55020000.ipu
[ 14.408362] remoteproc remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 4828304
[ 14.431040] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1
Starting TI IPC Daemon...
Starting uim-sysfs.service...
Starting Print notice about GPLv3 packages...
[ OK ] Started D-Bus System Message Bus.
[ 14.575401] virtio_rpmsg_bus virtio0: rpmsg host is online
[ 14.579295] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x32
[ 14.579438] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x33
[ 14.579567] virtio_rpmsg_bus virtio0: creating channel rpmsg-omx addr 0x3c
[ 14.579672] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x65
[ 14.619395] remoteproc remoteproc1: registered virtio0 (type 7)
[ 14.628019] remoteproc remoteproc1: remote processor 55020000.ipu is now up
[ 15.015884] remoteproc remoteproc0: powering up 58820000.ipu
[ 15.021989] remoteproc remoteproc0: Booting fw image dra7-ipu1-fw.xem4, size 6732532
[ 15.039061] omap-iommu 58882000.mmu: 58882000.mmu: version 2.1
[ 15.057202] of_get_named_gpiod_flags: can't parse 'gpio-reset' property of node '/ocp/i2c@48070000/tlv320aic3104@18[0]'
[ 15.093472] virtio_rpmsg_bus virtio1: rpmsg host is online
[ 15.111784] remoteproc remoteproc0: registered virtio1 (type 7)
[ 15.124567] remoteproc remoteproc0: remote processor 58820000.ipu is now up
[ 15.220433] virtio_rpmsg_bus virtio1: creating channel rpmsg-proto addr 0x3d
[ 15.236743] pixcir_ts 4-005c: GPIO lookup for consumer attb
[ 15.236749] pixcir_ts 4-005c: using device tree for GPIO lookup
[ 15.236825] of_get_named_gpiod_flags: can't parse 'attb-gpios' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]'
[ 15.237035] of_get_named_gpiod_flags: parsed 'attb-gpio' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]' - status (0)
[ 15.237051] pixcir_ts 4-005c: GPIO lookup for consumer reset
[ 15.237057] pixcir_ts 4-005c: using device tree for GPIO lookup
[ 15.237065] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]'
[ 15.237091] of_get_named_gpiod_flags: parsed 'reset-gpio' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]' - status (0)
[ 15.237202] pixcir_ts 4-005c: GPIO lookup for consumer wake
[ 15.237208] pixcir_ts 4-005c: using device tree for GPIO lookup
[ 15.237285] of_get_named_gpiod_flags: can't parse 'wake-gpios' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]'
[ 15.237292] of_get_named_gpiod_flags: can't parse 'wake-gpio' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]'
[ 15.237297] pixcir_ts 4-005c: using lookup tables for GPIO lookup
[ 15.237304] pixcir_ts 4-005c: lookup for GPIO wake failed
[ 15.240651] pixcir_ts 4-005c: GPIO lookup for consumer enable
[ 15.240734] pixcir_ts 4-005c: using device tree for GPIO lookup
[ 15.240744] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]'
[ 15.240751] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/ocp/i2c@4807c000/pixcir_ts@5c[0]'
[ 15.240757] pixcir_ts 4-005c: using lookup tables for GPIO lookup
[ 15.240763] pixcir_ts 4-005c: lookup for GPIO enable failed
[ 15.406350] pixcir_ts 4-005c: pixcir_set_power_mode: can't read reg 0x33 : -121
[ 15.406356] pixcir_ts 4-005c: Failed to set IDLE mode
[ 15.417119] pixcir_ts: probe of 4-005c failed with error -121
[ 15.850247] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
[ 15.857996] omap-des 480a5000.des: will run requests pump with realtime priority
[ 15.929156] omap_i2c 48060000.i2c: controller timed out
[ 15.965021] rtc-ds1307 2-006f: read error -110
[ 16.031512] rtc-ds1307: probe of 2-006f failed with error -110
[ 16.273789] omap_rtc 48838000.rtc: char device (253:2)
[ 16.286380] omap_rtc 48838000.rtc: registered as rtc2
[ 16.787955] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
[ 16.869415] vpe 489d0000.vpe: Device registered as /dev/video0
[ 16.927266] SCSI subsystem initialized
[ 17.097760] libata version 3.00 loaded.
[ 17.399195] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[ 17.407879] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 17.439167] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[ 17.490444] scsi host0: ahci
[ 17.495305] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 80
[ 17.738473] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
[ 17.817947] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3
[ 17.831763] omap-aes 4b500000.aes: will run requests pump with realtime priority
[ 17.839326] ata1: SATA link down (SStatus 0 SControl 300)
[ 17.908329] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3
[ 17.918682] omap-aes 4b700000.aes: will run requests pump with realtime priority
[ 17.951477] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
[ OK ] Reached target Containers.
Starting Login Service...
[ OK ] Started Periodic Command Scheduler.
[ OK ] Started Job spooling tools.
Starting RPC Bind Service...
[ OK ] Started System Logging Service.
[ OK ] Started TI MultiCore Tools Daemon.
[ OK ] Started TI IPC Daemon.
[ 18.481573] remoteproc remoteproc2: powering up 40800000.dsp
[ 18.488783] remoteproc remoteproc2: Booting fw image dra7-dsp1-fw.xe66, size 20559272
[ OK ] Found device /dev/ttyS2.
[ 18.573977] omap_hwmod: mmu0_dsp1: _wait_target_disable failed
[ 18.579895] omap-iommu 40d01000.mmu: 40d01000.mmu: version 3.0
[ 18.585913] omap-iommu 40d02000.mmu: 40d02000.mmu: version 3.0
[ 18.708261] remoteproc remoteproc3: powering up 41000000.dsp
[ 18.717802] remoteproc remoteproc3: Booting fw image dra7-dsp2-fw.xe66, size 20559272
[ 18.775007] omap_hwmod: mmu0_dsp2: _wait_target_disable failed
[ 18.780909] omap-iommu 41501000.mmu: 41501000.mmu: version 3.0
[ 18.786876] omap-iommu 41502000.mmu: 41502000.mmu: version 3.0
[ OK ] Started RPC Bind Service.
[ OK ] Started Network Service.
[ 18.883122] virtio_rpmsg_bus virtio2: rpmsg host is online
[ 18.883221] virtio_rpmsg_bus virtio2: creating channel rpmsg-proto addr 0x3d
[ 18.945979] remoteproc remoteproc2: registered virtio2 (type 7)
[ 18.973770] remoteproc remoteproc2: remote processor 40800000.dsp is now up
[ 19.004860] NET: Registered protocol family 15
[ 19.010201] omap-hdmi-audio omap-hdmi-audio.0.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok
[ 19.045282] omap-hdmi-audio omap-hdmi-audio.0.auto: ASoC: no DMI vendor name!
[ 19.073088] virtio_rpmsg_bus virtio3: rpmsg host is online
[ 19.073143] remoteproc remoteproc3: registered virtio3 (type 7)
[ 19.073150] remoteproc remoteproc3: remote processor 41000000.dsp is now up
[ 19.073179] virtio_rpmsg_bus virtio3: creating channel rpmsg-proto addr 0x3d
[ 19.362776] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem
[ 19.449813] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 19.546356] EXT4-fs (mmcblk0p2): recovery complete
[ 19.551358] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 19.828376] Initializing XFRM netlink socket
[ OK ] Created slice system-systemd\x2dbacklight.slice.
Starting Load/Save Screen Backlight…ightness of backlight:backlight...
[ OK ] Reached target Network.
Starting Simple Network Management Protocol (SNMP) Daemon....
Starting Enable and configure wl18xx bluetooth stack...
Starting Permit User Sessions...
Starting Network Name Resolution...
[ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlight.
[ OK ] Started Permit User Sessions.
[ OK ] Started Login Service.
[ OK ] Started Network Name Resolution.
[ OK ] Started uim-sysfs.service.
[ OK ] Started Simple Network Management Protocol (SNMP) Daemon..
[ 21.528394] pruss 4b200000.pruss: creating PRU cores and other child platform devices
[ 21.545039] pruss 4b280000.pruss: creating PRU cores and other child platform devices
[ 21.617355] NET: Registered protocol family 44
[ 21.632849] rpmsg_rpc virtio0.rpmsg-rpc.-1.101: probing service rpc_example_1 with src 1024 dst 101
[ 21.670428] rpmsg_rpc virtio0.rpmsg-rpc.-1.101: published functions = 8
[ 21.758160] remoteproc remoteproc4: 4b234000.pru is available
[ 21.772778] usbcore: registered new interface driver usbfs
[ 21.774636] usbcore: registered new interface driver hub
[ 21.775186] usbcore: registered new device driver usb
[ 21.795796] pru-rproc 4b234000.pru: PRU rproc node /ocp/pruss_soc_bus@4b226004/pruss@0/pru@34000 probed successfully
[ 21.814654] remoteproc remoteproc5: 4b238000.pru is available
[ 21.821962] pru-rproc 4b238000.pru: PRU rproc node /ocp/pruss_soc_bus@4b226004/pruss@0/pru@38000 probed successfully
[ 21.848469] remoteproc remoteproc6: 4b2b4000.pru is available
[ 21.855204] pru-rproc 4b2b4000.pru: PRU rproc node /ocp/pruss_soc_bus@4b2a6004/pruss@0/pru@34000 probed successfully
[ 21.867637] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.867665] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 21.873784] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010
[ 21.873843] xhci-hcd xhci-hcd.1.auto: irq 198, io mem 0x48890000
[ 21.880092] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 21.880100] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 21.880106] usb usb1: Product: xHCI Host Controller
[ 21.880111] usb usb1: Manufacturer: Linux 4.14.79-gbde58ab01e xhci-hcd
[ 21.880116] usb usb1: SerialNumber: xhci-hcd.1.auto
[ 21.885845] hub 1-0:1.0: USB hub found
[ 21.886893] hub 1-0:1.0: 1 port detected
[ 21.893858] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.893876] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 21.893890] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 21.894519] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.894696] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 21.894703] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 21.894709] usb usb2: Product: xHCI Host Controller
[ 21.894714] usb usb2: Manufacturer: Linux 4.14.79-gbde58ab01e xhci-hcd
[ 21.894719] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 21.895648] hub 2-0:1.0: USB hub found
[ 21.895682] hub 2-0:1.0: 1 port detected
[ 21.896232] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 21.896257] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[ 21.909392] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010
[ 21.909450] xhci-hcd xhci-hcd.2.auto: irq 199, io mem 0x488d0000
[ 21.909693] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 21.909701] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 21.909707] usb usb3: Product: xHCI Host Controller
[ 21.909712] usb usb3: Manufacturer: Linux 4.14.79-gbde58ab01e xhci-hcd
[ 21.909718] usb usb3: SerialNumber: xhci-hcd.2.auto
[ 21.910262] hub 3-0:1.0: USB hub found
[ 21.910307] hub 3-0:1.0: 1 port detected
[ 21.910699] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 21.910716] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[ 21.910728] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 21.911570] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.911743] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 21.911749] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 21.911754] usb usb4: Product: xHCI Host Controller
[ 21.911760] usb usb4: Manufacturer: Linux 4.14.79-gbde58ab01e xhci-hcd
[ 21.911765] usb usb4: SerialNumber: xhci-hcd.2.auto
[ 21.912283] hub 4-0:1.0: USB hub found
[ 21.912325] hub 4-0:1.0: 1 port detected
[ OK ] Started Enable and configure wl18xx bluetooth[ 22.196889] remoteproc remoteproc7: 4b2b8000.pru is available
stack.
[ 22.209701] pru-rproc 4b2b8000.pru: PRU rproc node /ocp/pruss_soc_bus@4b2a6004/pruss@0/pru@38000 probed successfully
[ 22.278974] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 22.469116] usb 3-1: New USB device found, idVendor=0424, idProduct=2514
[ 22.476302] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 22.487660] hub 3-1:1.0: USB hub found
[ 22.492900] hub 3-1:1.0: 4 ports detected
[ 22.848956] usb 3-1.3: new high-speed USB device number 3 using xhci-hcd
[ 22.999116] usb 3-1.3: New USB device found, idVendor=0424, idProduct=2514
[ 23.006277] usb 3-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 23.031090] hub 3-1.3:1.0: USB hub found
[ 23.035311] hub 3-1.3:1.0: 4 ports detected
[ 23.418942] usb 3-1.3.4: new high-speed USB device number 4 using xhci-hcd
[ 23.559228] usb 3-1.3.4: New USB device found, idVendor=0424, idProduct=2514
[ 23.566316] usb 3-1.3.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 23.606984] hub 3-1.3.4:1.0: USB hub found
[ 23.611721] hub 3-1.3.4:1.0: 4 ports detected
[ 23.958956] usb 3-1.3.4.2: new full-speed USB device number 5 using xhci-hcd
[ 24.090637] usb 3-1.3.4.2: New USB device found, idVendor=0483, idProduct=572a
[ 24.098350] usb 3-1.3.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 24.107194] usb 3-1.3.4.2: Product: Composite MSC + CDC
[ 24.113207] usb 3-1.3.4.2: Manufacturer: STMicroelectronics
[ 24.119219] usb 3-1.3.4.2: SerialNumber: 1111101010
[ 24.249814] usb 3-1.3.4.4: new high-speed USB device number 6 using xhci-hcd
[ 24.293264] cdc_acm 3-1.3.4.2:1.0: ttyACM0: USB ACM device
[ 24.302528] usbcore: registered new interface driver cdc_acm
[ 24.308557] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 24.379120] usb 3-1.3.4.4: New USB device found, idVendor=0424, idProduct=2514
[ 24.386835] usb 3-1.3.4.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 24.407414] hub 3-1.3.4.4:1.0: USB hub found
[ 24.412277] hub 3-1.3.4.4:1.0: 4 ports detected
[ 24.759003] usb 3-1.3.4.4.1: new full-speed USB device number 7 using xhci-hcd
[ 24.890804] usb 3-1.3.4.4.1: New USB device found, idVendor=0483, idProduct=572a
[ 24.898252] usb 3-1.3.4.4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 24.906353] usb 3-1.3.4.4.1: Product: Composite Device MSC + CDC
[ 24.912514] usb 3-1.3.4.4.1: Manufacturer: STMicroelectronics
[ 24.918368] usb 3-1.3.4.4.1: SerialNumber: 1111
[ 24.952720] cdc_acm 3-1.3.4.4.1:1.1: ttyACM1: USB ACM device
[ 25.058971] usb 3-1.3.4.4.4: new high-speed USB device number 8 using xhci-hcd
[ 25.145153] usb-storage 3-1.3.4.4.1:1.0: USB Mass Storage device detected
[ 25.154728] scsi host1: usb-storage 3-1.3.4.4.1:1.0
[ 25.163301] usbcore: registered new interface driver usb-storage
[ 25.189204] usb 3-1.3.4.4.4: New USB device found, idVendor=0424, idProduct=2514
[ 25.197113] usb 3-1.3.4.4.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 25.239294] hub 3-1.3.4.4.4:1.0: USB hub found
[ 25.244197] hub 3-1.3.4.4.4:1.0: 4 ports detected
[ 26.169503] scsi 1:0:0:0: Direct-Access STM Product 0.01 PQ: 0 ANSI: 2
[ 26.209827] sd 1:0:0:0: [sda] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
[ 26.218068] sd 1:0:0:0: [sda] Write Protect is off
[ 26.223694] sd 1:0:0:0: [sda] Mode Sense: 22 00 00 00
[ 26.229823] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 26.252772] sda: sda1
[ 26.257563] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 27.470473] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
***************************************************************
***************************************************************
NOTICE: This file system contains the following GPLv3 packages:
autoconf
bash-dev
bash
binutils-dev
binutils
bison-dev
bison
cifs-utils
cpio
cpp-symlinks
cpp
dosfstools
elfutils-dev
elfutils
g++-symlinks
g++
gawk
gcc-symlinks
gcc
gdb
gdbc6x
gdbserver
gettext
gzip
hidapi
libasm1
libdw1
libelf1
libgdbm-compat4
libgdbm-dev
libgdbm4
libgettextlib
libgettextsrc
libgmp10
libidn11
libmpc3
libmpfr4
libreadline-dev
libreadline7
libunistring2
m4-dev
m4
make
mc
nano
nettle
parted
python3-pycairo
rsyslog
which
If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution. This can be done using
the opkg remove command. i.e.:
opkg remove <package>
Where <package> is the name printed in the list above
NOTE: If the package is a dependency of another package you
will be notified of the dependent packages. You should
use the --force-removal-of-dependent-packages option to
also remove the dependent packages as well
***************************************************************
***************************************************************
[ OK ] Started Print notice about GPLv3 packages.
[ OK ] Reached target Sound Card.
Starting rc.pvr.service...
[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Started NFS status monitor for NFSv2/3 locking..
[ OK ] Started Serial Getty on ttyS2.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
Starting Synchronize System and HW clocks...
[FAILED] Failed to start Synchronize System and HW clocks.
See 'systemctl status sync-clocks.service' for details.
[ 29.296319] omap_hwmod: mmu0_dsp1: _wait_target_disable failed
[ 29.309377] omap_hwmod: mmu0_dsp2: _wait_target_disable failed
[ OK ] Started rc.pvr.service.
Starting telnetd.service...
[ OK ] Started telnetd.service.
Starting thttpd.service...
[ OK ] Started thttpd.service.
Starting rng-tools.service...
[ OK ] Started rng-tools.service.
Starting gdbserverproxy.service...
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am57xx-evm ttyS2
Arago 2018.10 am57xx-evm ttyS2
