This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

[参考译文] DRA746:使用 TS3A27518E 多路复用器时、eMMC1切换到总线宽度发生故障

Guru**** 647180 points
Other Parts Discussed in Thread: TS3A27518E, DRA746
请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1198108/dra746-emmc1-switch-to-bus-width-failed-with-ts3a27518e-multiplexer

器件型号:DRA746
主题中讨论的其他器件:TS3A27518E

尊敬的专家

我们在 定制电路板(DRA746)上存在 eMMC 安装问题。  客户使用多路复用器(TS3A27518E)通过 eMMC1选择其中一个存储器、方框图如下所示。

默认连接为 MTFC8GACA (Micron)

当系统尝试安装 MTFC8GACA 时,我们发现如下两条主要错误消息

(1) mmc0:切换到总线宽度1失败

(2) mmcblk0:错误-84传输数据,扇区?,nr 8,cmd 响应0x900,卡状态0xb00

2.610700] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.617392] [drm] No driver support for vblank timestamp query.
[    2.634855] [drm] Enabling DMM ywrap scrolling
[    2.639816] mmc0: MAN_BKOPS_EN bit is not set
[    2.641501] mmc0: switch to bus width 1 failed
[    2.641812] mmc0: new high speed MMC card at address 0001
[    2.642285] mmcblk0: mmc0:0001 R1J55A 7.28 GiB 
[    2.652516] mmcblk0boot0: mmc0:0001 R1J55A partition 1 8.00 MiB
[    2.662751] mmcblk0boot1: mmc0:0001 R1J55A partition 2 8.00 MiB
[    2.663495] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
[    2.663557] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
[    2.663562] mmcblk0: retrying using single block read
[    2.663786] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[    2.663793] blk_update_request: I/O error, dev mmcblk0, sector 0
[    2.663975] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[    2.663980] blk_update_request: I/O error, dev mmcblk0, sector 1
[    2.664159] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[    2.664164] blk_update_request: I/O error, dev mmcblk0, sector 2
[    2.664345] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[    2.664350] blk_update_request: I/O error, dev mmcblk0, sector 3
[    2.664684] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
[    2.664689] blk_update_request: I/O error, dev mmcblk0, sector 5
[    2.665022] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
[    2.665027] blk_update_request: I/O error, dev mmcblk0, sector 7
[    2.665032] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[    2.665256] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
[    2.665310] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
[    2.665313] mmcblk0: retrying using single block read
[    2.665544] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[    2.665549] blk_update_request: I/O error, dev mmcblk0, sector 0
[    2.665728] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[    2.665732] blk_update_request: I/O error, dev mmcblk0, sector 1
[    2.665910] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[    2.665914] blk_update_request: I/O error, dev mmcblk0, sector 2
[    2.666393] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
[    2.666398] blk_update_request: I/O error, dev mmcblk0, sector 5
[    2.666728] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0

 

因此、我们尝试检查 eMMC0信息、看起来 DRA746可以检测  MTFC8GACA

root@wnc-j6:~# cat /sys/kernel/debug/mmc*/ios
clock:      52000000 Hz
vdd:     21 (3.3 ~ 3.4 V)
bus mode:   2 (push-pull)
chip select:   0 (don't care)
power mode: 2 (on)
bus width:  2 (4 bits)
timing spec:   1 (mmc high-speed)
signal voltage:   0 (3.30 V)
driver type:   0 (driver type B)

器件树如下所示:

&mmc1 {
	status = "okay";
	vmmc-supply = <&evm_3v3_sd>;
	vmmc_aux-supply = <&ldo1_reg>;
	bus-width = <4>;
	//cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
	max-frequency = <192000000>;
	pinctrl-names = "default", "hs";
	pinctrl-0 = <&mmc1_pins_default>;
	pinctrl-1 = <&mmc1_pins_hs>;
};

我们以如下方式引用 E2E:

https://e2e.ti.com/support/processors-group/processors/f/processors-forum/934051/am3354-am335x-mmc1-switch-to-bus-width-8-failed

https://e2e.ti.com/support/processors-group/processors/f/processors-forum/629097/linux-am5728-custom-board-emmc-issue

https://e2e.ti.com/support/processors-group/processors/f/processors-forum/805352/linux-am5728-emmc-configuration-issue

我认为(猜)数据线(D0~D3)可能会有一些问题、因为系统尝试切换总线宽度时会发生错误。

能否有人给我们提供一些调试方向? (包括软件和硬件)

非常感谢

吉布斯

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    Hi Gibbs、

    您能否澄清 多路复用为 SD 模式是否正常工作? 仅在切换到 eMMC 时才会出现问题? 您能解释一下您试图为每个速度模式配置哪些速度模式吗? 请注意、MMC1仅支持 eMMC 高达高速 DDR。

    此致、

    马可

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    您好、Marco

    谢谢你的答复,抱歉,我的网站有点延迟.

    请按以下方式回答您的问题:

    1. 您能否说明 多路复用为 SD 模式是否工作正常?

    不可以、切换到 SD 时会出现相同的加载问题。

    问题仅在切换到 eMMC 时发生?

    不会、也会发生 SD 接口。

    3.  您能否说明您尝试为每种模式配置哪些速度模式? (emmc1接口)

    我们已经做了一些测试。 我们发现只有"default speed" CLK = 24MHz 可以正常运行、没有安装错误消息、但当我们让 emmc1在"high speed (HS mode)"时钟下运行时、CLK = 48MHz 时钟会再次显示安装错误消息。

    4. 请注意、MMC1仅支持 eMMC 的最高高速 DDR。

    当然、根据客户 emmc1配置、我认为它们的最大速度是 HS 模式。 (3.3V)

    据我所知、我们是不能调整 emmc1"信号驱动"模式的、对吗?

    所以、时钟升高后、似乎会发生错误。

    它可能是"信号驱动器"或"时序问题"、对吗?

    谢谢

    吉布斯

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    您好、尊敬的 Expert

    一周的通行证、对我有什么建议吗?

    非常感谢

    吉布斯

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    Hi Gibbs、

    默认速度在 eMMC 和 SD 上正确运行、但这两个版本上的高速模式都无法正常运行?

    如何在 MMC1上在 DS 和 HS 模式之间交换、以及在 eMMC 和 SD 模式之间交换?

    您能否验证多路复用器和所使用的任何上拉电阻器之间的连接、并在此处分享更准确的原理图?

    MMC 模式的驱动强度可以在 MMCHS_AC12[21:20] DS_SEL 处修改、而 SD 模式的驱动强度可以在 CTRL_CORE_CONTROL_HYST_1[30:29] SDCARD_IC 处修改。

    谢谢。此致、

    马可

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    大家好、Macro

    感谢您的回复。

    让我来回答您的问题。

    1、 默认速度在 eMMC 和 SD 上都能正常运行,但在这两种模式下都能正常运行?

    多路复用器默认交换以连接 eMMC。  我们认为、我们可能首先缩小这个问题的范围、我们可能首先专门进行 eMMC 调试。 "默认速度"(24MHz 时钟)运行良好、但高速(48MHz 时钟)出现故障。 我们认为时钟速度是一个因素。

    2.如何在 MMC1上在 DS 和 HS 模式之间切换、以及在 eMMC 和 SD 模式之间切换?

    我们仅测试 eMMC、不让多路复用器执行交换通道功能、 多路复用器默认连接是 eMMC。 我们修改了 Linux 器件树、以强制 DRA746在 DS 或 HS 模式下工作。

    3.能否验证多路复用器和所用的上拉电阻的连接、并在这里分享更准确的原理图?

    当然、我会让客户直接在这里发帖。  

    4. MMC 模式的驱动强度可以在 MMCHS_AC12[21:20] DS_SEL 修改、SD 模式的驱动强度可以在 CTRL_CORE_CONTROL_HYST_1[30:29] SDCARD_IC 修改。

    谢谢、让我先复查一下。

    吉布斯

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    Hi Gibbs、Macro、

    1.我们发现问题出在将电压从3.3V 变为1.8V 之后消失了。  此处是 DTS (从3.3V 更改为1.8V)更改。 在 ldo1_reg 中、电压变化为1.VMMC-supply =<&evm_1v8_sd> 2.set regulator-max-microvoltage =<1800000>:

    diff --git a/board-support/linux/arch/arm/boot/dts/dra7-evm-030003.dts b/board-support/linux/arch/arm/boot/dts/dra7-evm-030003.dts
    index 36cfa54..2d60198 100644
    --- a/board-support/linux/arch/arm/boot/dts/dra7-evm-030003.dts
    +++ b/board-support/linux/arch/arm/boot/dts/dra7-evm-030003.dts
    @@ -76,6 +76,15 @@
                    regulator-boot-on;
            };
    
    +       evm_1v8_sd: fixedregulator-sd {
    +               compatible = "regulator-fixed";
    +               regulator-name = "evm_1v8_sd";
    +               regulator-min-microvolt = <1800000>;
    +               regulator-max-microvolt = <1800000>;
    +               regulator-always-on;
    +               regulator-boot-on;
    +       };
    +
            evm_3v3_sw: fixedregulator-evm_3v3_sw {
                    compatible = "regulator-fixed";
                    regulator-name = "evm_3v3_sw";
    @@ -1569,7 +1578,7 @@
                                            /* LDO1_OUT --> SDIO  */
                                            regulator-name = "ldo1";
                                            regulator-min-microvolt = <1800000>;
    -                                       regulator-max-microvolt = <3300000>;
    +                                       regulator-max-microvolt = <1800000>;
                                            regulator-always-on;
                                            regulator-boot-on;
                                    };
    @@ -1880,11 +1889,16 @@ i2c_p3_exp: &i2c2 {
    
     &mmc1 {
            status = "okay";
    -       vmmc-supply = <&evm_3v3_sd>;
    +       vmmc-supply = <&evm_1v8_sd>;
            vmmc_aux-supply = <&ldo1_reg>;
            bus-width = <4>;
            //cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
            max-frequency = <192000000>;
    +#if 1
    +       pinctrl-names = "default", "hs";
    +       pinctrl-0 = <&mmc1_pins_default>;
    +       pinctrl-1 = <&mmc1_pins_hs>;
    +#else
            pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
            pinctrl-0 = <&mmc1_pins_default>;
            pinctrl-1 = <&mmc1_pins_hs>;
    @@ -1895,6 +1909,7 @@ i2c_p3_exp: &i2c2 {
            pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
            pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr50_rev20_conf>;
            pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
    +#endif
    

    当我们多路复用到 SD 时、此 DTB 无法从 SD 引导、并且它会在"Waiting for..."字符时挂起、错误日志为:

    [    2.682730] omap_hsmmc 4809c000.mmc: no support for card's volts
    [    2.688813] mmc0: error -22 whilst initialising SD card
    ..
    [    3.870665] Waiting for root device PARTUUID=fe13d755-02...

    2.在 HS 模式下改变1.8V 是否合理?根据数据表, HS 模式以3.3V 运行?

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    尊敬的 Kevin:

    我不明白为什么在这里将电源更改为1.8V 会适用于 HS 模式。 您正在使用哪个软件版本? 您是否有 SOC->Multiplex->MMC/SD 连接的原理图?

    此致、

    马可

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    尊敬的 Marco:

    1.我查询4.4.y 分支、 从 https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/?h=linux-4.4.y 构建它 zImage 、并 将 zImage 应用于我们电路板中的原始 DTS (HS + 3.3V)。 事实证明、问题已经解决、来自/sys/kernel/debug/mmc1/ios 的信号电压变为1.8V (由于某种原因、我不知道、因此我没有进行数字说明)。 因此、我尝试在 DTS 中将电压从3.3更改为1.8、问题迎刃而解。

    2.我们使用的是 PROCESSOR-SDK-LINUX-AUTOMOTIVE-03.02.00.03。

    3. MMC1的硬件设计 使用 多路复用器切换到 J12 SD 卡或 U52 EMMC 4位存储器、如下所示:

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    您需要更新到最新的 SDK 版本(6.00.00.03)、以确保软件没有引入任何已知的勘误表。 MMC1应能够在1.8V 和3.3V 速度模式之间动态切换、而 MMC2/3/4无法实现这一点、需要一个固定电压来满足其运行速度。 您是否具有1.8V 下成功案例的启动日志? 您能否确认 MMC1是否实际在 HS 模式下运行、以及 IO 是否在1.8V 的电压下运行?

    马可

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

     最新 SDK 版本(6.00.00.03)的内核将卡在"Waiting for root device PARTUUID = bddb4f41-02...":

    U-Boot SPL 2016.05 (Nov 24 2017 - 15:38:03)
    DRA752-GP ES2.0
    *** Warning - bad CRC, using default environment
    
    Trying to boot from MMC2_2
    spl: falcon_args_file not set in environment, falling back to default
    reading args
    spl_load_image_fat_os: error reading image args, err - -1
    reading u-boot.img
    reading u-boot.img
    
    
    U-Boot 2016.05 (Nov 24 2017 - 15:38:03 +0800)
    
    CPU  : DRA752-GP ES2.0
    Board: DRA74x EVM REV
    I2C:   ready
    DRAM:  2 GiB
    MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
    *** Warning - bad CRC, using default environment
    
    Warning: fastboot.board_rev: unknown board revision
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid GPT ***
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid Backup GPT ***
    ERROR: cannot find partition: 'userdata'
    
    at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size()
    Warning: fastboot.userdata_size: unable to calc
    Net:   <ethaddr> not set. Validating first E-fuse MAC
    Could not get PHY for cpsw: addr 2
    cpsw
    Hit any key to stop autoboot:  0
    J6 ...
    switch to partitions #0, OK
    mmc1(part 0) is current device
    SD/MMC found on device 1
    4403712 bytes read in 220 ms (19.1 MiB/s)
    113603 bytes read in 13 ms (8.3 MiB/s)
    Booting from mmc1 ...
    Kernel image @ 0x82000000 [ 0x000000 - 0x433200 ]
    ## Flattened Device Tree blob at 88000000
       Booting using the fdt blob at 0x88000000
       Loading Device Tree to 8ffe1000, end 8ffffbc2 ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Linux version 4.19.73-g31275c05a1 (oe-user@oe-host) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #1 SMP PREEMPT Wed Dec 11 12:53:11 UTC 2019
    [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
    [    0.000000] CPU: div instructions available: patching division code
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [    0.000000] OF: fdt: Machine model: TI DRA742 Bowei 20170929 17:30
    [    0.000000] Memory policy: Data cache writealloc
    [    0.000000] efi: Getting EFI parameters from FDT:
    [    0.000000] efi: UEFI not found.
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
    [    0.000000] OF: reserved mem: initialized node ipu2_cma@95800000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
    [    0.000000] OF: reserved mem: initialized node dsp1_cma@99000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
    [    0.000000] OF: reserved mem: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x000000009f000000, size 8 MiB
    [    0.000000] OF: reserved mem: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool
    [    0.000000] cma: Reserved 24 MiB at 0x00000000fd400000
    [    0.000000] OMAP4: Map 0x00000000fed00000 to (ptrval) for dram barrier
    [    0.000000] DRA752 ES2.0
    [    0.000000] random: get_random_bytes called from start_kernel+0xb4/0x470 with crng_init=0
    [    0.000000] percpu: Embedded 16 pages/cpu s36492 r8192 d20852 u65536
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516416
    [    0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=bddb4f41-02 rw rootfstype=ext4 rootwait consoleblank=0 omapdrm.num_crtc=2 drm.debug=0xff
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Memory: 1847196K/2072576K available (10240K kernel code, 341K rwdata, 2800K rodata, 2048K init, 269K bss, 36964K reserved, 188416K cma-reserved, 1265664K highmem)
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    [    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (12256 kB)
    [    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   (2048 kB)
    [    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 342 kB)
    [    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   ( 270 kB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] rcu: Preemptible hierarchical RCU implementation.
    [    0.000000]  Tasks RCU enabled.
    [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
    [    0.000000] ti_dt_clocks_register: missing clkctrl nodes, please update your dts.
    [    0.000000] OMAP clockevent source: timer1 at 31475 Hz
    [    0.000000] arch_timer: cp15 timer(s) running at 5.90MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns
    [    0.000005] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns
    [    0.000018] Switching to timer-based delay loop, resolution 169ns
    [    0.000352] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
    [    0.000362] OMAP clocksource: 32k_counter at 32768 Hz
    [    0.000825] Console: colour dummy device 80x30
    [    0.000844] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
    [    0.000852] This ensures that you still see kernel messages. Please
    [    0.000860] update your kernel commandline.
    [    0.000893] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016)
    [    0.000910] pid_max: default: 32768 minimum: 301
    [    0.001037] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001053] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001614] CPU: Testing write buffer coherency: ok
    [    0.001652] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
    [    0.001863] /cpus/cpu@0 missing clock-frequency property
    [    0.001883] /cpus/cpu@1 missing clock-frequency property
    [    0.001895] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [    0.059892] Setting up static identity map for 0x80200000 - 0x80200060
    [    0.079902] rcu: Hierarchical SRCU implementation.
    [    0.100098] EFI services will not be available.
    [    0.119963] smp: Bringing up secondary CPUs ...
    [    0.200303] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [    0.200309] CPU1: Spectre v2: using ICIALLU workaround
    [    0.200429] smp: Brought up 1 node, 2 CPUs
    [    0.200442] SMP: Total of 2 processors activated (23.60 BogoMIPS).
    [    0.200451] CPU: All CPU(s) started in SVC mode.
    [    0.200917] devtmpfs: initialized
    [    0.221580] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
    [    0.221840] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.221858] futex hash table entries: 512 (order: 3, 32768 bytes)
    [    0.224710] pinctrl core: initialized pinctrl subsystem
    [    0.225222] DMI not present or invalid.
    [    0.225501] NET: Registered protocol family 16
    [    0.226666] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.227660] omap_hwmod: l3_main_2 using broken dt data from ocp
    [    0.249323] omap_hwmod: dma_system: no dt node
    [    0.249333] ------------[ cut here ]------------
    [    0.249356] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.249365] omap_hwmod: dma_system: doesn't have mpu register target base
    [    0.249373] Modules linked in:
    [    0.249391] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.73-g31275c05a1 #1
    [    0.249401] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.249409] Backtrace:
    [    0.249431] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.249443]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.249459] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.249474] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.249485]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.249497] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.249509]  r9:c104b824 r8:00000000 r7:c121252c r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.249524] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.249534]  r3:c0dd0a04 r2:c0dd0560
    [    0.249543]  r5:00000000 r4:c12124f4
    [    0.249558] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.249570]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.249579]  r4:c12124f4
    [    0.249594] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.249604]  r5:c1204c48 r4:c1255740
    [    0.249619] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.249630]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.249647] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.249658]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.249666]  r4:00000000
    [    0.249679] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.249688] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.249698] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.249709] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.249719] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.249728]  r5:c0a0ccd8 r4:00000000
    [    0.249740] ---[ end trace 53f2d3aef28cd7ec ]---
    [    0.266863] omap_hwmod: hdq1w: no dt node
    [    0.266873] ------------[ cut here ]------------
    [    0.266889] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.266898] omap_hwmod: hdq1w: doesn't have mpu register target base
    [    0.266905] Modules linked in:
    [    0.266922] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         4.19.73-g31275c05a1 #1
    [    0.266931] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.266939] Backtrace:
    [    0.266957] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.266969]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.266983] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.266996] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.267007]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.267019] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.267031]  r9:c104b824 r8:00000000 r7:c12117c0 r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.267045] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.267054]  r3:c0dd26fc r2:c0dd0560
    [    0.267064]  r5:00000000 r4:c1211788
    [    0.267078] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.267090]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.267098]  r4:c1211788
    [    0.267113] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.267123]  r5:c1204c48 r4:c1255740
    [    0.267138] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.267150]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.267166] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.267178]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.267186]  r4:00000000
    [    0.267199] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.267208] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.267217] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.267227] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.267237] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.267246]  r5:c0a0ccd8 r4:00000000
    [    0.267255] ---[ end trace 53f2d3aef28cd7ed ]---
    [    0.298674] omap_hwmod: smartreflex_core: no dt node
    [    0.298684] ------------[ cut here ]------------
    [    0.298699] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.298708] omap_hwmod: smartreflex_core: doesn't have mpu register target base
    [    0.298716] Modules linked in:
    [    0.298731] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         4.19.73-g31275c05a1 #1
    [    0.298740] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.298747] Backtrace:
    [    0.298765] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.298777]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.298791] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.298804] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.298815]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.298828] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.298839]  r9:c104b824 r8:00000000 r7:c120fcc8 r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.298854] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.298863]  r3:c0dd2248 r2:c0dd0560
    [    0.298872]  r5:00000000 r4:c120fc90
    [    0.298886] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.298898]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.298907]  r4:c120fc90
    [    0.298920] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.298929]  r5:c1204c48 r4:c1255740
    [    0.298944] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.298955]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.298971] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.298981]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.298989]  r4:00000000
    [    0.299002] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.299011] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.299021] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.299032] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.299042] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.299051]  r5:c0a0ccd8 r4:00000000
    [    0.299060] ---[ end trace 53f2d3aef28cd7ee ]---
    [    0.300114] omap_hwmod: smartreflex_mpu: no dt node
    [    0.300123] ------------[ cut here ]------------
    [    0.300137] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.300145] omap_hwmod: smartreflex_mpu: doesn't have mpu register target base
    [    0.300152] Modules linked in:
    [    0.300168] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         4.19.73-g31275c05a1 #1
    [    0.300176] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.300184] Backtrace:
    [    0.300200] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.300212]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.300225] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.300238] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.300248]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.300260] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.300272]  r9:c104b824 r8:00000000 r7:c120fc54 r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.300285] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.300295]  r3:c0dd2238 r2:c0dd0560
    [    0.300303]  r5:00000000 r4:c120fc1c
    [    0.300318] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.300330]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.300338]  r4:c120fc1c
    [    0.300352] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.300361]  r5:c1204c48 r4:c1255740
    [    0.300376] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.300386]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.300401] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.300412]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.300420]  r4:00000000
    [    0.300432] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.300441] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.300451] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.300461] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.300471] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.300480]  r5:c0a0ccd8 r4:00000000
    [    0.300503] ---[ end trace 53f2d3aef28cd7ef ]---
    [    0.413727] cpuidle: using governor ladder
    [    0.413762] cpuidle: using governor menu
    [    0.420395] OMAP GPIO hardware version 0.1
    [    0.423350] GPIO line 161 (radio_rst) hogged as output/low
    [    0.449103] No ATAGs?
    [    0.449182] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [    0.449198] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.449234] omap_device: omap_dma_system: build failed (-22)
    [    0.449245] omap2_system_dma_init_dev: Can't build omap_device for omap_dma_system:dma_system.
    [    0.449617] omap4_sram_init:Unable to allocate sram needed to handle errata I688
    [    0.449628] omap4_sram_init:Unable to get sram pool needed to handle errata I688
    [    0.461236] edma 43300000.edma: memcpy is disabled
    [    0.464490] edma 43300000.edma: TI EDMA DMA engine driver
    [    0.468860] omap-iommu 40d01000.mmu: 40d01000.mmu registered
    [    0.469038] omap-iommu 40d02000.mmu: 40d02000.mmu registered
    [    0.469268] omap-iommu 58882000.mmu: 58882000.mmu registered
    [    0.469500] omap-iommu 55082000.mmu: 55082000.mmu registered
    [    0.469891] omap-iommu 41501000.mmu: 41501000.mmu registered
    [    0.470063] omap-iommu 41502000.mmu: 41502000.mmu registered
    [    0.470321] iommu: Adding device 58820000.ipu to group 1
    [    0.470395] iommu: Adding device 55020000.ipu to group 2
    [    0.470518] iommu: Adding device 40800000.dsp to group 0
    [    0.470755] iommu: Adding device 41000000.dsp to group 3
    [    0.472051] SCSI subsystem initialized
    [    0.473214] palmas 0-0058: IRQ missing: skipping irq request
    [    0.502012] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0
    [    0.503460] SMPS12: supplied by regulator-dummy
    [    0.504494] SMPS3: supplied by regulator-dummy
    [    0.505977] SMPS45: supplied by regulator-dummy
    [    0.507899] SMPS6: supplied by regulator-dummy
    [    0.509678] SMPS7: supplied by regulator-dummy
    [    0.511619] SMPS8: supplied by regulator-dummy
    [    0.513416] SMPS9: supplied by regulator-dummy
    [    0.514430] LDO1: supplied by regulator-dummy
    [    0.522497] LDO2: supplied by regulator-dummy
    [    0.532355] LDO3: supplied by regulator-dummy
    [    0.542366] LDO4: supplied by regulator-dummy
    [    0.542480] random: fast init done
    [    0.543106] LDO5: supplied by regulator-dummy
    [    0.543822] LDO6: supplied by regulator-dummy
    [    0.544536] LDO7: supplied by regulator-dummy
    [    0.545258] LDO8: supplied by regulator-dummy
    [    0.545983] LDO9: supplied by regulator-dummy
    [    0.552407] LDOLN: supplied by regulator-dummy
    [    0.562428] LDOUSB: supplied by regulator-dummy
    [    0.574354] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
    [    0.575034] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
    [    0.575434] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
    [    0.575819] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
    [    0.576208] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
    [    0.576442] media: Linux media interface: v0.10
    [    0.576481] videodev: Linux video capture interface: v2.00
    [    0.576554] pps_core: LinuxPPS API ver. 1 registered
    [    0.576564] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.576585] PTP clock support registered
    [    0.576615] EDAC MC: Ver: 3.0.0
    [    0.577357] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
    [    0.577608] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
    [    0.578128] Advanced Linux Sound Architecture Driver Initialized.
    [    0.578905] clocksource: Switched to clocksource arch_sys_counter
    [    0.586764] NET: Registered protocol family 2
    [    0.587353] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
    [    0.587382] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.587446] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.587573] TCP: Hash tables configured (established 8192 bind 8192)
    [    0.587646] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [    0.587680] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [    0.587809] NET: Registered protocol family 1
    [    0.608247] RPC: Registered named UNIX socket transport module.
    [    0.608257] RPC: Registered udp transport module.
    [    0.608266] RPC: Registered tcp transport module.
    [    0.608275] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.609320] hw perfevents: no interrupt-affinity property for /pmu, guessing.
    [    0.609542] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
    [    0.610512] Initialise system trusted keyrings
    [    0.610637] workingset: timestamp_bits=14 max_order=19 bucket_order=5
    [    0.615512] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.626001] NFS: Registering the id_resolver key type
    [    0.626021] Key type id_resolver registered
    [    0.626030] Key type id_legacy registered
    [    0.626072] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.627627] Key type asymmetric registered
    [    0.627639] Asymmetric key parser 'x509' registered
    [    0.627686] bounce: pool size: 64 pages
    [    0.627721] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
    [    0.627732] io scheduler noop registered
    [    0.627741] io scheduler deadline registered
    [    0.627838] io scheduler cfq registered (default)
    [    0.627849] io scheduler mq-deadline registered
    [    0.627859] io scheduler kyber registered
    [    0.632793] pinctrl-single 4a003400.pinmux: please update dts to use #pinctrl-cells = <1>
    [    0.633318] pinctrl-single 4a003400.pinmux: 282 pins, size 1128
    [    0.640553] pbias_mmc_omap5: Bringing 3300000uV into 3000000-3000000uV
    [    0.640569] pbias_mmc_omap5: failed to apply 3000000-3000000uV constraint(-22)
    [    0.640584] pbias-regulator 4a002e00.pbias_regulator: Failed to register regulator: -22
    [    0.640607] pbias-regulator: probe of 4a002e00.pbias_regulator failed with error -22
    [    0.641433] evm_3v3_sw: supplied by sysen1
    [    0.641672] aic_dvdd: supplied by evm_3v3_sw
    [    0.641746] vtt_fixed: supplied by sysen2
    [    0.684673] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled
    [    0.688596] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
    [    0.689534] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 44, base_baud = 3000000) is a 8250
    [    0.690440] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 45, base_baud = 3000000) is a 8250
    [    2.662588] console [ttyS2] enabled
    [    2.667015] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 46, base_baud = 3000000) is a 8250
    [    2.676670] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 47, base_baud = 3000000) is a 8250
    [    2.686320] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 48, base_baud = 3000000) is a 8250
    [    2.695978] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 49, base_baud = 3000000) is a 8250
    [    2.707068] omap_rng 48090000.rng: Random Number Generator ver. 20
    [    2.707405] random: crng init done
    [    2.717505] omapdss_dss 58000000.dss: Linked as a consumer to regulator.22
    [    2.724599] DSS: OMAP DSS rev 6.1
    [    2.729644] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
    [    2.750327] brd: module loaded
    [    2.759517] loop: module loaded
    [    2.768957] libphy: Fixed MDIO Bus: probed
    [    2.828934] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000
    [    2.836627] davinci_mdio 48485000.mdio: no live phy, scanning all
    [    2.939022] davinci_mdio 48485000.mdio: timed out waiting for user access
    [    3.045927] davinci_mdio 48485000.mdio: timed out waiting for idle
    [    3.052180] davinci_mdio: probe of 48485000.mdio failed with error -5
    [    3.059289] cpsw 48484000.ethernet: Detected MACID = 54:45:38:a7:aa:1e
    [    3.065891] cpsw 48484000.ethernet: initialized cpsw ale version 1.4
    [    3.072295] cpsw 48484000.ethernet: ALE Table size 1024
    [    3.077569] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies)
    [    3.085580] cpsw 48484000.ethernet: cpsw: Detected MACID = 54:45:38:a7:aa:1f
    [    3.094209] i2c /dev entries driver
    [    3.102604] cpu cpu0: "syscon" is missing, cannot use OPPv2 table.
    [    3.109347] sdhci: Secure Digital Host Controller Interface driver
    [    3.115555] sdhci: Copyright(c) Pierre Ossman
    [    3.120930] omap_hsmmc: probe of 4809c000.mmc failed with error -22
    [    3.127666] omap_hsmmc 480b4000.mmc: RX DMA channel request failed
    [    3.134325] omap_hsmmc 480d1000.mmc: RX DMA channel request failed
    [    3.140842] sdhci-pltfm: SDHCI platform and OF driver helper
    [    3.147883] ledtrig-cpu: registered to indicate activity on CPUs
    [    3.158457] pinctrl-single 4a003400.pinmux: pin PIN170 already requested by 4806a000.serial; cannot claim for 48460000.mcasp
    [    3.169766] pinctrl-single 4a003400.pinmux: pin-170 (48460000.mcasp) status -22
    [    3.177113] pinctrl-single 4a003400.pinmux: could not request pin 170 (PIN170) from group mcasp1_pins  on device pinctrl-single
    [    3.188662] davinci-mcasp 48460000.mcasp: Error applying setting, reverse things back
    [    3.196555] davinci-mcasp: probe of 48460000.mcasp failed with error -22
    [    3.203365] pinctrl-single 4a003400.pinmux: pin PIN192 already requested by 4806a000.serial; cannot claim for 48464000.mcasp
    [    3.214653] pinctrl-single 4a003400.pinmux: pin-192 (48464000.mcasp) status -22
    [    3.222021] pinctrl-single 4a003400.pinmux: could not request pin 192 (PIN192) from group mcasp2_pins  on device pinctrl-single
    [    3.233565] davinci-mcasp 48464000.mcasp: Error applying setting, reverse things back
    [    3.241452] davinci-mcasp: probe of 48464000.mcasp failed with error -22
    [    3.248237] pinctrl-single 4a003400.pinmux: pin PIN203 already requested by 4806a000.serial; cannot claim for 48468000.mcasp
    [    3.259523] pinctrl-single 4a003400.pinmux: pin-203 (48468000.mcasp) status -22
    [    3.266867] pinctrl-single 4a003400.pinmux: could not request pin 203 (PIN203) from group mcasp3_pins  on device pinctrl-single
    [    3.278408] davinci-mcasp 48468000.mcasp: Error applying setting, reverse things back
    [    3.286294] davinci-mcasp: probe of 48468000.mcasp failed with error -22
    [    3.293092] pinctrl-single 4a003400.pinmux: pin PIN205 already requested by 4806a000.serial; cannot claim for 4846c000.mcasp
    [    3.304377] pinctrl-single 4a003400.pinmux: pin-205 (4846c000.mcasp) status -22
    [    3.311736] pinctrl-single 4a003400.pinmux: could not request pin 205 (PIN205) from group mcasp4_pins  on device pinctrl-single
    [    3.323278] davinci-mcasp 4846c000.mcasp: Error applying setting, reverse things back
    [    3.331166] davinci-mcasp: probe of 4846c000.mcasp failed with error -22
    [    3.337955] pinctrl-single 4a003400.pinmux: pin PIN200 already requested by 4806a000.serial; cannot claim for 4847c000.mcasp
    [    3.349246] pinctrl-single 4a003400.pinmux: pin-200 (4847c000.mcasp) status -22
    [    3.356590] pinctrl-single 4a003400.pinmux: could not request pin 200 (PIN200) from group mcasp8_pins  on device pinctrl-single
    [    3.368134] davinci-mcasp 4847c000.mcasp: Error applying setting, reverse things back
    [    3.376023] davinci-mcasp: probe of 4847c000.mcasp failed with error -22
    [    3.383480] NET: Registered protocol family 10
    [    3.388888] Segment Routing with IPv6
    [    3.392659] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
    [    3.399094] NET: Registered protocol family 17
    [    3.403756] Key type dns_resolver registered
    [    3.408154] Registering SWP/SWPB emulation handler
    [    3.412990] omap_voltage_late_init: Voltage driver support not added
    [    3.419391] Power Management for TI OMAP4+ devices.
    [    3.424978] Loading compiled-in X.509 certificates
    [    3.446882] dmm 4e000000.dmm: failed to initialize work-around for i878
    [    3.455039] dmm 4e000000.dmm: initialized all PAT entries
    [    3.461135] omapdrm omapdrm.0: omap_modeset_init failed: ret=-517
    [    3.468175] omapdrm omapdrm.0: omap_modeset_init failed: ret=-517
    [    3.475138] omapdrm omapdrm.0: omap_modeset_init failed: ret=-517
    [    3.481870] hctosys: unable to open rtc device (rtc0)
    [    3.487585] aic_dvdd: disabling
    [    3.490956] ldousb: disabling
    [    3.494251] ALSA device list:
    [    3.497232]   No soundcards found.
    [    3.501323] Waiting for root device PARTUUID=bddb4f41-02...
    
    

     

    2. DateCode2244/2245在1.8V 下成功引导的引导日志:

    U-Boot SPL 2016.05 (Nov 24 2017 - 15:38:03)
    DRA752-GP ES2.0
    *** Warning - bad CRC, using default environment
    
    Trying to boot from MMC2_2
    spl: falcon_args_file not set in environment, falling back to default
    reading args
    spl_load_image_fat_os: error reading image args, err - -1
    reading u-boot.img
    reading u-boot.img
    
    
    U-Boot 2016.05 (Nov 24 2017 - 15:38:03 +0800)
    
    CPU  : DRA752-GP ES2.0
    Board: DRA74x EVM REV
    I2C:   ready
    DRAM:  2 GiB
    MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
    *** Warning - bad CRC, using default environment
    
    Warning: fastboot.board_rev: unknown board revision
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid GPT ***
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid Backup GPT ***
    ERROR: cannot find partition: 'userdata'
    
    at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size()
    Warning: fastboot.userdata_size: unable to calc
    Net:   <ethaddr> not set. Validating first E-fuse MAC
    Could not get PHY for cpsw: addr 2
    cpsw
    Hit any key to stop autoboot:  0
    J6 ...
    switch to partitions #0, OK
    mmc1(part 0) is current device
    SD/MMC found on device 1
    4281344 bytes read in 213 ms (19.2 MiB/s)
    113071 bytes read in 12 ms (9 MiB/s)
    Booting from mmc1 ...
    Kernel image @ 0x82000000 [ 0x000000 - 0x415400 ]
    ## Flattened Device Tree blob at 88000000
       Booting using the fdt blob at 0x88000000
       Loading Device Tree to 8ffe1000, end 8ffff9ae ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpuset
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Initializing cgroup subsys cpuacct
    [    0.000000] Linux version 4.4.45 (bowei@bowei-Veriton-M490) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #75 SMP PREEMPT Mon Jan 22 10:50:18 CST 2018
    [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [    0.000000] Machine model: TI DRA742 Louis 20170929 17:30
    [    0.000000] Reserved memory: created CMA memory pool at 0x95800000, size 56 MiB
    [    0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x99000000, size 64 MiB
    [    0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9d000000, size 32 MiB
    [    0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9f000000, size 8 MiB
    [    0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool
    [    0.000000] cma: Reserved 24 MiB at 0xfd400000
    [    0.000000] Memory policy: Data cache writealloc
    [    0.000000] OMAP4: Map 0xfee00000 to fe600000 for dram barrier
    [    0.000000] DRA752 ES2.0
    [    0.000000] PERCPU: Embedded 12 pages/cpu @eed51000 s18944 r8192 d22016 u49152
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 516672
    [    0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=bddb4f41-02 rw rootfstype=ext4 rootwait consoleblank=0 omapdrm.num_crtc=2 drm.debug=0xff
    [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Memory: 1851432K/2073600K available (7719K kernel code, 797K rwdata, 4560K rodata, 372K init, 291K bss, 33752K reserved, 188416K cma-reserved, 1266688K highmem)
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    [    0.000000]       .text : 0xc0008000 - 0xc0c0607c   (12281 kB)
    [    0.000000]       .init : 0xc0c07000 - 0xc0c64000   ( 372 kB)
    [    0.000000]       .data : 0xc0c64000 - 0xc0d2b530   ( 798 kB)
    [    0.000000]        .bss : 0xc0d2d000 - 0xc0d75f00   ( 292 kB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] Preemptible hierarchical RCU implementation.
    [    0.000000]  Build-time adjustment of leaf fanout to 32.
    [    0.000000] NR_IRQS:16 nr_irqs:16 16
    [    0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div
    [    0.000000] OMAP clockevent source: timer1 at 31475 Hz
    [    0.000000] Architected cp15 timer(s) running at 5.90MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns
    [    0.000004] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns
    [    0.000015] Switching to timer-based delay loop, resolution 169ns
    [    0.000325] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
    [    0.000333] OMAP clocksource: 32k_counter at 32768 Hz
    [    0.000786] Console: colour dummy device 80x30
    [    0.000803] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
    [    0.000810] This ensures that you still see kernel messages. Please
    [    0.000816] update your kernel commandline.
    [    0.000828] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016)
    [    0.000841] pid_max: default: 32768 minimum: 301
    [    0.000934] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.000944] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001474] Initializing cgroup subsys io
    [    0.001492] Initializing cgroup subsys memory
    [    0.001515] Initializing cgroup subsys devices
    [    0.001528] Initializing cgroup subsys freezer
    [    0.001539] Initializing cgroup subsys perf_event
    [    0.001550] Initializing cgroup subsys pids
    [    0.001576] CPU: Testing write buffer coherency: ok
    [    0.001771] /cpus/cpu@0 missing clock-frequency property
    [    0.001787] /cpus/cpu@1 missing clock-frequency property
    [    0.001797] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [    0.001837] Setting up static identity map for 0x80008340 - 0x800083a0
    [    0.080051] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [    0.080113] Brought up 2 CPUs
    [    0.080126] SMP: Total of 2 processors activated (23.60 BogoMIPS).
    [    0.080133] CPU: All CPU(s) started in SVC mode.
    [    0.081170] devtmpfs: initialized
    [    0.111084] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
    [    0.112068] omap_hwmod: l3_main_2 using broken dt data from ocp
    [    0.310433] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.314133] pinctrl core: initialized pinctrl subsystem
    [    0.314996] NET: Registered protocol family 16
    [    0.315935] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.340217] cpuidle: using governor ladder
    [    0.370240] cpuidle: using governor menu
    [    0.378504] OMAP GPIO hardware version 0.1
    [    0.382624] GPIO line 161 (radio_rst) hogged as output/low
    [    0.414591] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [    0.414601] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.415081] omap4_sram_init:Unable to allocate sram needed to handle errata I688
    [    0.415090] omap4_sram_init:Unable to get sram pool needed to handle errata I688
    [    0.415576] OMAP DMA hardware revision 0.0
    [    0.461550] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
    [    0.462798] edma 43300000.edma: memcpy is disabled
    [    0.467537] edma 43300000.edma: TI EDMA DMA engine driver
    [    0.471761] omap-iommu 40d01000.mmu: 40d01000.mmu registered
    [    0.471943] omap-iommu 40d02000.mmu: 40d02000.mmu registered
    [    0.472102] omap-iommu 58882000.mmu: 58882000.mmu registered
    [    0.472260] omap-iommu 55082000.mmu: 55082000.mmu registered
    [    0.472557] omap-iommu 41501000.mmu: 41501000.mmu registered
    [    0.472749] omap-iommu 41502000.mmu: 41502000.mmu registered
    [    0.474753] SCSI subsystem initialized
    [    0.476005] ======palmas_i2c_probe:526========
    [    0.476022] ======palmas_i2c_probe:559, features=0x0========
    [    0.476333] palmas 0-0058: IRQ missing: skipping irq request
    [    0.491064] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0
    [    0.562796] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
    [    0.563432] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
    [    0.563797] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
    [    0.564169] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
    [    0.564534] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
    [    0.564756] media: Linux media interface: v0.10
    [    0.564806] Linux video capture interface: v2.00
    [    0.564844] pps_core: LinuxPPS API ver. 1 registered
    [    0.564851] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.564874] PTP clock support registered
    [    0.564900] EDAC MC: Ver: 3.0.0
    [    0.565665] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
    [    0.565959] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
    [    0.566304] Advanced Linux Sound Architecture Driver Initialized.
    [    0.567188] clocksource: Switched to clocksource arch_sys_counter
    [    0.577940] NET: Registered protocol family 2
    [    0.578431] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.578494] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.578619] TCP: Hash tables configured (established 8192 bind 8192)
    [    0.578665] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [    0.578698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [    0.578907] NET: Registered protocol family 1
    [    0.579172] RPC: Registered named UNIX socket transport module.
    [    0.579181] RPC: Registered udp transport module.
    [    0.579187] RPC: Registered tcp transport module.
    [    0.579193] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.580238] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
    [    0.582696] futex hash table entries: 512 (order: 3, 32768 bytes)
    [    0.589425] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.590074] NFS: Registering the id_resolver key type
    [    0.590098] Key type id_resolver registered
    [    0.590106] Key type id_legacy registered
    [    0.590171] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.592152] bounce: pool size: 64 pages
    [    0.592306] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
    [    0.592323] io scheduler noop registered
    [    0.592337] io scheduler deadline registered
    [    0.592371] io scheduler cfq registered (default)
    [    0.597689] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
    [    0.658363] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
    [    0.661951] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 299, base_baud = 3000000) is a 8250
    [    0.662826] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 300, base_baud = 3000000) is a 8250
    [    0.663687] console [ttyS2] disabled
    [    0.663732] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250
    [    1.550527] console [ttyS2] enabled
    [    1.554926] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 302, base_baud = 3000000) is a 8250
    [    1.564654] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 303, base_baud = 3000000) is a 8250
    [    1.574335] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 304, base_baud = 3000000) is a 8250
    [    1.584013] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 305, base_baud = 3000000) is a 8250
    [    1.594154] [drm] Initialized drm 1.1.0 20060810
    [    1.600370] OMAP DSS rev 6.1
    [    1.604134] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
    [    1.625872] brd: module loaded
    [    1.634088] loop: module loaded
    [    1.643758] libphy: Fixed MDIO Bus: probed
    [    1.648467] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
    [    1.655547] e1000: Copyright (c) 1999-2006 Intel Corporation.
    [    1.661395] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    [    1.667267] e1000e: Copyright(c) 1999 - 2015     2.019967] tvp5158 1-0058: ERROR: Chip id is not TVP5158
    [    2.025505] ov1063x 1-0037: ov1063x Product ID 0 Manufacturer ID 0
    [    2.031731] ov1063x 1-0037: ov1063x 1-0037 sensor driver registered !!
    [    2.039140] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
    [    2.046236] vip 48990000.vip: loading firmware vpdma-1b8.bin
    [    2.055636] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr104 mode
    [    2.062254] omap_hsmmc 4809c000.mmc: no pinctrl state for ddr50 mode
    [    2.068685] vpe 489d0000.vpe: Device registered as /dev/video0
    [    2.074558] vip 48990000.vip: VPDMA firmware loaded
    [    2.079496] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr50 mode
    [    2.079606] vip2-s1: Port B: Using subdev ov1063x 1-0037 for capture
    [    2.092316] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr25 mode
    [    2.092334] vip2-s1: device registered as video1
    [    2.103347] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr12 mode
    [    2.110958] ldo1: voltage operation not allowed
    [    2.115512] omap_hsmmc 4809c000.mmc: vmmc_aux set voltage failed
    [    2.121567] omap_hsmmc 4809c000.mmc: failed to switch to 3v
    [    2.167614] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
    [    2.173998] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
    [    2.180403] omap_hsmmc 480b4000.mmc: no pinctrl state for hs200_1_8v mode
    [    2.187373] evm_3v3_sw: supplied by sysen1
    [    2.227553] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr25 mode
    [    2.233936] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr12 mode
    [    2.240334] omap_hsmmc 480d1000.mmc: no pinctrl state for hs mode
    [    2.278007] ledtrig-cpu: registered to indicate activity on CPUs
    [    2.286092] hwspinlock_user gatemp: requested 10 hwspinlocks
    [    2.307085] pinctrl-single 4a003400.pinmux: pin 4a0036a8.0 already requested by 4806a000.serial; cannot claim for 48460000.mcasp
    [    2.318722] pinctrl-single 4a003400.pinmux: pin-170 (48460000.mcasp) status -22
    [    2.326065] pinctrl-single 4a003400.pinmux: could not request pin 170 (4a0036a8.0) from group mcasp1_pins  on device pinctrl-single
    [    2.337990] davinci-mcasp 48460000.mcasp: Error applying setting, reverse things back
    [    2.346265] davinci-mcasp 48460000.mcasp: Update the bindings to use assigned-clocks!
    [    2.354169] davinci-mcasp 48460000.mcasp: failed to reparent fck
    [    2.360453] pinctrl-single 4a003400.pinmux: pin 4a003700.0 already requested by 4806a000.serial; cannot claim for 48464000.mcasp
    [    2.372083] pinctrl-single 4a003400.pinmux: pin-192 (48464000.mcasp) status -22
    [    2.379466] pinctrl-single 4a003400.pinmux: could not request pin 192 (4a003700.0) from group mcasp2_pins  on device pinctrl-single
    [    2.391353] davinci-mcasp 48464000.mcasp: Error applying setting, reverse things back
    [    2.399601] davinci-mcasp 48464000.mcasp: Update the bindings to use assigned-clocks!
    [    2.407503] davinci-mcasp 48464000.mcasp: failed to reparent fck
    [    2.413764] pinctrl-single 4a003400.pinmux: pin 4a00372c.0 already requested by 4806a000.serial; cannot claim for 48468000.mcasp
    [    2.425394] pinctrl-single 4a003400.pinmux: pin-203 (48468000.mcasp) status -22
    [    2.432746] pinctrl-single 4a003400.pinmux: could not request pin 203 (4a00372c.0) from group mcasp3_pins  on device pinctrl-single
    [    2.444630] davinci-mcasp 48468000.mcasp: Error applying setting, reverse things back
    [    2.452883] davinci-mcasp 48468000.mcasp: Update the bindings to use assigned-clocks!
    [    2.460781] davinci-mcasp 48468000.mcasp: failed to reparent fck
    [    2.467029] pinctrl-single 4a003400.pinmux: pin 4a003734.0 already requested by 4806a000.serial; cannot claim for 4846c000.mcasp
    [    2.478659] pinctrl-single 4a003400.pinmux: pin-205 (4846c000.mcasp) status -22
    [    2.486000] pinctrl-single 4a003400.pinmux: could not request pin 205 (4a003734.0) from group mcasp4_pins  on device pinctrl-single
    [    2.497884] davinci-mcasp 4846c000.mcasp: Error applying setting, reverse things back
    [    2.506119] davinci-mcasp 4846c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.514017] davinci-mcasp 4846c000.mcasp: failed to reparent fck
    [    2.520274] pinctrl-single 4a003400.pinmux: pin 4a003720.0 already requested by 4806a000.serial; cannot claim for 4847c000.mcasp
    [    2.531903] pinctrl-single 4a003400.pinmux: pin-200 (4847c000.mcasp) status -22
    [    2.539259] pinctrl-single 4a003400.pinmux: could not request pin 200 (4a003720.0) from group mcasp8_pins  on device pinctrl-single
    [    2.551144] davinci-mcasp 4847c000.mcasp: Error applying setting, reverse things back
    [    2.559399] davinci-mcasp 4847c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.567295] davinci-mcasp 4847c000.mcasp: failed to reparent fck
    [    2.574511] NET: Registered protocol family 10
    [    2.589790] sit: IPv6 over IPv4 tunneling driver
    [    2.594962] NET: Registered protocol family 17
    [    2.599689] Key type dns_resolver registered
    [    2.604103] omap_voltage_late_init: Voltage driver support not added
    [    2.611013] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    2.617234] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    2.623486] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    2.630118] Power Management for TI OMAP4+ devices.
    [    2.635259] Registering SWP/SWPB emulation handler
    [    2.642711] dmm 4e000000.dmm: initialized all PAT entries
    [    2.670836] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [    2.677498] [drm] No driver support for vblank timestamp query.
    [    2.694269] [drm] Enabling DMM ywrap scrolling
    [    2.700353] mmc0: MAN_BKOPS_EN bit is not set
    [    2.766111] mmc0: new high speed MMC card at address 0001
    [    2.769704] Console: switching to colour frame buffer device 240x67
    [    2.776758] mmcblk0: mmc0:0001 R1J55A 7.28 GiB
    [    2.787071] mmcblk0boot0: mmc0:0001 R1J55A partition 1 128 KiB
    [    2.787361] mmcblk0boot1: mmc0:0001 R1J55A partition 2 128 KiB
    [    2.789666]  mmcblk0: p1
    [    2.819602] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
    [    2.840325] mmc1: MAN_BKOPS_EN bit is not set
    [    2.848456] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
    [    2.876112] asoc-simple-card-mcasp1 sound@1: bt-sco-pcm-mcasp1 <-> 48460000.mcasp mapping ok
    [    2.885192] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPLOUT
    [    2.895052] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.904698] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPROUT
    [    2.912491] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.922113] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for LLOUT
    [    2.929912] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.938926] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for RLOUT
    [    2.946616] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.955625] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3L
    [    2.963148] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.972157] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3R
    [    2.979688] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.988698] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for Mic Bias
    [    2.996648] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.005920] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1L
    [    3.013570] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.022585] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1R
    [    3.030200] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.041140] asoc-simple-card-mcasp2 sound@2: bt-sco-pcm-mcasp2 <-> 48464000.mcasp mapping ok
    [    3.049640] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPLOUT
    [    3.057436] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.067046] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPROUT
    [    3.074836] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.084456] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for LLOUT
    [    3.092158] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.101190] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for RLOUT
    [    3.108899] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.117910] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3L
    [    3.125425] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.134431] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3R
    [    3.141957] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.150966] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for Mic Bias
    [    3.158928] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.168201] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1L
    [    3.175804] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.184813] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1R
    [    3.192463] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.203248] asoc-simple-card-mcasp3 sound@3: bt-sco-pcm-mcasp3 <-> 48468000.mcasp mapping ok
    [    3.211747] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPLOUT
    [    3.217732] mmc1: new DDR MMC card at address 0001
    [    3.224358] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.228252] mmcblk1: mmc1:0001 R1J55A 7.28 GiB
    [    3.238527] mmcblk1boot0: mmc1:0001 R1J55A partition 1 128 KiB
    [    3.244403] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPROUT
    [    3.248798] mmcblk1boot1: mmc1:0001 R1J55A partition 2 128 KiB
    [    3.253032]  mmcblk1: p1 p2
    [    3.260869] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.270494] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for LLOUT
    [    3.278203] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.287215] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for RLOUT
    [    3.294904] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.303945] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3L
    [    3.311478] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.320489] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3R
    [    3.328017] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.337016] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for Mic Bias
    [    3.344690] mmc2: host does not support reading read-only switch, assuming write-enable
    [    3.344758] mmc2: new SDHC card at address 0001
    [    3.355217] mmcblk2: mmc2:0001 SD4GB 3.64 GiB
    [    3.357067]  mmcblk2: p1 p2
    [    3.364844] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.374128] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1L
    [    3.381745] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.390761] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1R
    [    3.398378] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.409327] asoc-simple-card-mcasp4 sound@4: bt-sco-pcm-mcasp4 <-> 4846c000.mcasp mapping ok
    [    3.417832] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPLOUT
    [    3.425611] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.435232] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPROUT
    [    3.443023] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.452645] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for LLOUT
    [    3.460342] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.469352] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for RLOUT
    [    3.477041] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.486050] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3L
    [    3.493577] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.502613] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3R
    [    3.510142] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.519153] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for Mic Bias
    [    3.527103] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.536374] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1L
    [    3.543984] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.552994] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1R
    [    3.560604] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.571782] asoc-simple-card-mcasp8 sound@8: bt-sco-pcm-mcasp8 <-> 4847c000.mcasp mapping ok
    [    3.580284] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPLOUT
    [    3.588077] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.597697] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPROUT
    [    3.605474] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.615090] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for LLOUT
    [    3.622793] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.631802] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for RLOUT
    [    3.639503] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.648514] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3L
    [    3.656027] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.665036] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3R
    [    3.672562] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.681572] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for Mic Bias
    [    3.689533] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.698836] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1L
    [    3.706439] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.715447] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1R
    [    3.723063] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.732961] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    3.739190] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    3.745445] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    3.752502] hctosys: unable to open rtc device (rtc0)
    [    3.769351] aic_dvdd: disabling
    [    3.772756] ldousb: disabling
    [    3.776239] ALSA device list:
    [    3.779235]   #0: DRA7xx-EVM-MCASP1
    [    3.782737]   #1: DRA7xx-EVM-MCASP2
    [    3.786237]   #2: DRA7xx-EVM-MCASP3
    [    3.789751]   #3: DRA7xx-EVM-MCASP4
    [    3.793250]   #4: DRA7xx-EVM-MCASP8
    [    3.865870] EXT4-fs (mmcblk1p2): recovery complete
    [    3.871133] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
    [    3.879308] VFS: Mounted root (ext4 filesystem) on device 179:50.
    [    3.886821] devtmpfs: mounted
    [    3.890040] Freeing unused kernel memory: 372K (c0c07000 - c0c64000)
    [    3.896420] This architecture does not have kernel memory protection.
    INIT: version 2.88 booting
    Starting udev
    [    4.183148] udevd[129]: starting version 182
    [    4.641595] omap-rproc 58820000.ipu: assigned reserved memory node ipu1_cma@9d000000
    [    4.720397]  remoteproc0: 58820000.ipu is available
    [    4.872043]  remoteproc0: Note: remoteproc is still under development and considered experimental.
    [    4.987275]  remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.014205] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.014593]  remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2
    [    5.014601]  remoteproc0: failed to load dra7-ipu1-fw.xem4
    [    5.015604] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@95800000
    [    5.015663]  remoteproc1: 55020000.ipu is available
    [    5.015667]  remoteproc1: Note: remoteproc is still under development and considered experimental.
    [    5.015670]  remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.017603] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@99000000
    [    5.017660]  remoteproc2: 40800000.dsp is available
    [    5.017664]  remoteproc2: Note: remoteproc is still under development and considered experimental.
    [    5.017667]  remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.018494] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9f000000
    [    5.018545]  remoteproc3: 41000000.dsp is available
    [    5.018549]  remoteproc3: Note: remoteproc is still under development and considered experimental.
    [    5.018551]  remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.027750] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20
    [    5.029286] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
    [    5.045557]  remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2
    [    5.045566]  remoteproc3: failed to load dra7-dsp2-fw.xe66
    [    5.046387]  remoteproc2: registered virtio0 (type 7)
    [    5.060817] alg: skcipher: setkey failed on test 5 for ecb-des-omap: flags=100
    [    5.061147] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    5.061496] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    5.089779]  remoteproc1: registered virtio1 (type 7)
    [    5.159347] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0
    [    5.296794] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.304018] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.309334] ahci 4a140000.sata: forcing port_map 0x0 -> 0x1
    [    5.309379] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
    [    5.309389] ahci 4a140000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst
    [    5.353718] CAN device driver interface
    [    5.431211] scsi host0: ahci
    [    5.434490] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 347
    [    5.447787] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.491596] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
    [    5.509469] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.515799] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.697724] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.703949] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.885968] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    udevd[619]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    udevd[622]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory[    6.521364] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    
    
    [    6.522740] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
    [    6.523824] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3
    udevd[632]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    udevd[631]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    [    6.572664] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.580392] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.598777] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.604997] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    udevd[635]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    [    6.674951] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.742146] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3
    [    6.742315] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.742319] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.742379] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.767522] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.773739] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.778761] pinctrl-single 4a003400.pinmux: pin 4a0037d0.0 already requested by 4806a000.serial; cannot claim for 4ae3c000.can
    [    6.778768] pinctrl-single 4a003400.pinmux: pin-244 (4ae3c000.can) status -22
    [    6.778776] pinctrl-single 4a003400.pinmux: could not request pin 244 (4a0037d0.0) from group dcan1_pins_sleep  on device pinctrl-single
    [    6.778781] c_can_platform 4ae3c000.can: Error applying setting, reverse things back
    [    6.779620] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=367)
    [    6.799069] [drm] Initialized pvr 1.14.3699939 20110701 on minor 1
    [    6.864750] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.877872] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.889538] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.903924] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.052233]  remoteproc2: powering up 40800000.dsp
    [    7.062233]  remoteproc2: Booting fw image dra7-dsp1-fw.xe66, size 929770
    [    7.075814] omap_hwmod: mmu0_dsp1: _wait_target_disable failed
    [    7.081713] omap-iommu 40d01000.mmu: 40d01000.mmu: version 3.0
    [    7.087676] omap-iommu 40d02000.mmu: 40d02000.mmu: version 3.0
    [    7.150509]  remoteproc2: remote processor 40800000.dsp is now up
    [    7.157127] virtio_rpmsg_bus virtio0: rpmsg host is online
    [    7.162697] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x36
    [    7.170809] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.177022] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.183402] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x37
    [    7.191342] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x3b
    [    7.191481] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.204775]  remoteproc1: powering up 55020000.ipu
    [    7.215526]  remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 3484972
    [    7.222805] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1
    [    7.289460]  remoteproc1: remote processor 55020000.ipu is now up
    [    7.296421] virtio_rpmsg_bus virtio1: rpmsg host is online
    [    7.301984] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x3b
    [    7.309293] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.315502] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.330607] rpmsg_rpc rpmsg2: probing service rpmsg-dce-dsp with src 1024 dst 59
    [    7.337861] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.338203] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.338207] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.338258] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.363717] rpmsg_rpc rpmsg3: probing service rpmsg-dce with src 1024 dst 59
    [    7.363981] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.363986] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.364037] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.364133] rpmsg_rpc rpmsg2: published functions = 8
    [    7.395425] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.401975] rpmsg_rpc rpmsg3: published functions = 8
    [    7.406225] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.406304] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.557022] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.557531] dwc3 48910000.usb: failed to register ULPI interface
    [    7.557561] dwc3: probe of 48910000.usb failed with error -110
    [    7.579085] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.585405] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.588391] usbcore: registered new interface driver usbfs
    [    7.588998] usbcore: registered new interface driver hub
    [    7.589636] usbcore: registered new device driver usb
    [    7.597673] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    7.597698] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
    [    7.603740] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010
    [    7.603798] xhci-hcd xhci-hcd.0.auto: irq 445, io mem 0x48890000
    [    7.604928] hub 1-0:1.0: USB hub found
    [    7.604966] hub 1-0:1.0: 1 port detected
    [    7.605385] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    7.605399] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
    [    7.605485] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
    [    7.606482] hub 2-0:1.0: USB hub found
    [    7.606518] hub 2-0:1.0: 1 port detected
    [    7.606987] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
    [    7.607011] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
    [    7.607421] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010
    [    7.607469] xhci-hcd xhci-hcd.1.auto: irq 446, io mem 0x488d0000
    [    7.608516] hub 3-0:1.0: USB hub found
    [    7.608552] hub 3-0:1.0: 1 port detected
    [    7.608942] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
    [    7.608956] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
    [    7.609040] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
    [    7.610038] hub 4-0:1.0: USB hub found
    [    7.610073] hub 4-0:1.0: 1 port detected
    [    7.738006] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.744218] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.750564] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [   15.497208] ata1: softreset failed (1st FIS failed)
    [   25.507206] ata1: softreset failed (1st FIS failed)
    [   25.857213] ata1: SATA link down (SStatus 0 SControl 300)
    [   25.911882] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
    Starting Bootlog daemon: bootlogd.
    [   25.991990] random: dd: uninitialized urandom read (512 bytes read, 82 bits of entropy available)
    ALSA: Restoring mixer settings...
    No state is present for card DRA7xxEVMMCASP1
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP1
    No state is present for card DRA7xxEVMMCASP2
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP2
    No state is present for card DRA7xxEVMMCASP3
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP3
    No state is present for card DRA7xxEVMMCASP4
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP4
    No state is present for card DRA7xxEVMMCASP8
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP8
    Thu Sep  3 18:41:00 UTC 2015
    
    
    
    2017.11.23 15:00
    
    
    
    This version is for J6
    
    
    
    ****** This application only support ASCII code 0 to 127 ******
    
    
    
    ****** This application only support CB version #F ******
    [   41.433664] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   41.439692] usb usb4: USB disconnect, device number 1
    [   41.447339] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
    [   41.453060] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   41.458641] usb usb3: USB disconnect, device number 1
    [   41.469097] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
    [   41.476486] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   41.481618] usb usb2: USB disconnect, device number 1
    [   41.489682] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
    [   41.495391] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   41.500510] usb usb1: USB disconnect, device number 1
    [   41.508540] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
    [   41.627843] usbcore: deregistering device driver usb
    [   41.634408] usbcore: deregistering interface driver usbfs
    [   41.645342] usbcore: deregistering interface driver hub
    [AB_server.c, make_sure_usb_kernel_stack_removed, 374] temp: drwxr-xr-x   27 root     root             0 Jan  1  1970 .
    dr-xr-xr-x   12 root     root             0 Jan  1  1970 ..
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ac97
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clockevents
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clocksource
    drwxr-xr-x    4 root     root             0 Jan  1  1970 container
    drwxr-xr-x    4 root     root             0 Jan  1  1970 cpu
    drwxr-xr-x    4 root     root             0 Jan  1  1970 edac
    drwxr-xr-x    4 root     root             0 Jan  1  1970 event_source
    drwxr-xr-x    4 root     root             0 Jan  1  1970 hid
    drwxr-xr-x    4 root     root             0 Jan  1  1970 i2c
    drwxr-xr-x    4 root     root             0 Jan  1  1970 iio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mdio_bus
    drwxr-xr-x    4 root     root             0 Jan  1  1970 media
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mipi-dsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mmc
    drwxr-xr-x    5 root     root             0 Jan  1  1970 pci
    drwxr-xr-x    4 root     root             0 Jan  1  1970 platform
    drwxr-xr-x    4 root     root             0 Jan  1  1970 rpmsg
    drwxr-xr-x    4 root     root             0 Jan  1  1970 scsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 sdio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 serio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 soc
    drwxr-xr-x    4 root     root             0 Jan  1  1970 spi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ulpi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 virtio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 workqueue
    
    [AB_server.c, AB_boot_finish, 181] AB boot success, pull high GPIO
    [AB_server.c, AB_boot_finish, 187] AB boot success, pull high GPIO finished
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    /usr/local/bin/set_unused_gpio_input: line 14: echo: write error: Device or resource busy
    /usr/local/bin/set_unused_gpio_input: line 15: /sys/class/gpio/gpio161/direction: No such file or directory
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    INIT: Entering runlevel: 5
    Configuring network interfaces... [   43.330140] net eth0: initializing cpsw version 1.15 (0)
    [   43.335508] net eth0: initialized cpsw ale version 1.4
    [   43.341101] net eth0: ALE Table size 1024
    [   43.348183] libphy: PHY 48485000.mdio:02 not found
    [   43.353001] net eth0: phy "48485000.mdio:02" not found on slave 0, err -19
    [   43.366926] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    /bin/sh: udhcpc: command not found
    done.
    Starting system message bus: [   43.423376] random: dbus-daemon: uninitialized urandom read (12 bytes read, 106 bits of entropy available)
    [   43.439586] random: dbus-daemon: uninitialized urandom read (12 bytes read, 106 bits of entropy available)
    dbus.
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (4) Bytes
    
    
    _version[0]: 30
    _version[1]: 31
    _version[2]: 31
    _version[3]: 30
    _version[4]: 0
    _version[5]: 0
    _version[6]: 0
    _version[7]: 0
    _version[8]: 0
    _version[9]: 0
    _version[10]: 0
    _version[11]: 0
    _version[12]: 0
    _version[13]: 0
    _version[14]: 0
    _version[15]: 0
    [AB_server.c, main, 517] AB_server: get CB's HW version 0110
    
    
    [AB_server.c, get_CB_hardware_version_finish, 254] AB get CB hw version finish, gpio pull low
    [AB_server.c, send_AB_model_info_to_CB, 279] write AB model info total (6) Bytes, model: (DRA74X
    )
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    UIM SYSFS Node Not Found
    Starting telnet daemon.
    Starting tiipclad daemon[AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 1
     ______
    [AB_server.c, sync_CB_status, 312] ______ AB GPIO 109 1, can go ______
    
    GateMP support enabled on host
    
    Opened log file: lad.txt
    
    numProcessors = 5 id = 0 baseId = 0
    
    Spawned daemon: /usr/bin/lad_dra7xx
    
    .
    Starting rpcbind daemon...done.
    creating NFS state directory: done
    starting statd: done
    NFS daemon support not enabled in kernel
    Starting syslogd/klogd: done
    Starting thttpd.
    Enabling thermal zones...
    Stopping Bootlog daemon: bootlogd.
    
    root@wnc-j6:~# [AB_server.c, main, 550] ulpi on/off : J6, ULPI test on
    cat /sys/kernel/debug/mmc0/i[   54.779077] random: nonblocking pool is initialized
    os
    clock:          52000000 Hz
    vdd:            7 (1.65 - 1.95 V)
    bus mode:       2 (push-pull)
    chip select:    0 (don't care)
    power mode:     2 (on)
    bus width:      2 (4 bits)
    timing spec:    1 (mmc high-speed)
    signal voltage: 0 (1.80 V)
    driver type:    0 (driver type B)
    root@wnc-j6:~# lsblk
    NAME         MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
    mmcblk0boot0 179:16   0  128K  1 disk
    mmcblk0boot1 179:32   0  128K  1 disk
    mmcblk1boot0 179:64   0  128K  1 disk
    mmcblk1boot1 179:80   0  128K  1 disk
    mmcblk0      179:0    0  7.3G  0 disk
    `-mmcblk0p1  179:1    0  7.3G  0 part
    mmcblk1      179:48   0  7.3G  0 disk
    |-mmcblk1p1  179:49   0   64M  0 part
    `-mmcblk1p2  179:50   0  7.2G  0 part /
    mmcblk2      179:96   0  3.7G  0 disk
    |-mmcblk2p1  179:97   0   62M  0 part
    `-mmcblk2p2  179:98   0  3.6G  0 part
    root@wnc-j6:~#
    

    3.请访问/sys/kernel/debug/mmc0/ios 以确认 MMC0是否正在运行 HS。 是的、硬件检测电压为1.8V。

    4. DateCode2244/2245的引导日志 显示错误消息(有时是紧急消息) 在3.3V 时引导:

    U-Boot SPL 2016.05 (Nov 24 2017 - 15:38:03)
    DRA752-GP ES2.0
    *** Warning - bad CRC, using default environment
    
    Trying to boot from MMC2_2
    spl: falcon_args_file not set in environment, falling back to default
    reading args
    spl_load_image_fat_os: error reading image args, err - -1
    reading u-boot.img
    reading u-boot.img
    
    
    U-Boot 2016.05 (Nov 24 2017 - 15:38:03 +0800)
    
    CPU  : DRA752-GP ES2.0
    Board: DRA74x EVM REV
    I2C:   ready
    DRAM:  2 GiB
    MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
    *** Warning - bad CRC, using default environment
    
    Warning: fastboot.board_rev: unknown board revision
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid GPT ***
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid Backup GPT ***
    ERROR: cannot find partition: 'userdata'
    
    at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size()
    Warning: fastboot.userdata_size: unable to calc
    Net:   <ethaddr> not set. Validating first E-fuse MAC
    Could not get PHY for cpsw: addr 2
    cpsw
    Hit any key to stop autoboot:  0
    J6 ...
    switch to partitions #0, OK
    mmc1(part 0) is current device
    SD/MMC found on device 1
    4281344 bytes read in 214 ms (19.1 MiB/s)
    113603 bytes read in 12 ms (9 MiB/s)
    Booting from mmc1 ...
    Kernel image @ 0x82000000 [ 0x000000 - 0x415400 ]
    ## Flattened Device Tree blob at 88000000
       Booting using the fdt blob at 0x88000000
       Loading Device Tree to 8ffe1000, end 8ffffbc2 ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpuset
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Initializing cgroup subsys cpuacct
    [    0.000000] Linux version 4.4.45 (bowei@bowei-Veriton-M490) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #75 SMP PREEMPT Mon Jan 22 10:50:18 CST 2018
    [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [    0.000000] Machine model: TI DRA742 Bowei 20170929 17:30
    [    0.000000] Reserved memory: created CMA memory pool at 0x95800000, size 56 MiB
    [    0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x99000000, size 64 MiB
    [    0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9d000000, size 32 MiB
    [    0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9f000000, size 8 MiB
    [    0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool
    [    0.000000] cma: Reserved 24 MiB at 0xfd400000
    [    0.000000] Memory policy: Data cache writealloc
    [    0.000000] OMAP4: Map 0xfee00000 to fe600000 for dram barrier
    [    0.000000] DRA752 ES2.0
    [    0.000000] PERCPU: Embedded 12 pages/cpu @eed51000 s18944 r8192 d22016 u49152
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 516672
    [    0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=bddb4f41-02 rw rootfstype=ext4 rootwait consoleblank=0 omapdrm.num_crtc=2 drm.debug=0xff
    [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Memory: 1851432K/2073600K available (7719K kernel code, 797K rwdata, 4560K rodata, 372K init, 291K bss, 33752K reserved, 188416K cma-reserved, 1266688K highmem)
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    [    0.000000]       .text : 0xc0008000 - 0xc0c0607c   (12281 kB)
    [    0.000000]       .init : 0xc0c07000 - 0xc0c64000   ( 372 kB)
    [    0.000000]       .data : 0xc0c64000 - 0xc0d2b530   ( 798 kB)
    [    0.000000]        .bss : 0xc0d2d000 - 0xc0d75f00   ( 292 kB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] Preemptible hierarchical RCU implementation.
    [    0.000000]  Build-time adjustment of leaf fanout to 32.
    [    0.000000] NR_IRQS:16 nr_irqs:16 16
    [    0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div
    [    0.000000] OMAP clockevent source: timer1 at 31475 Hz
    [    0.000000] Architected cp15 timer(s) running at 5.90MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns
    [    0.000004] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns
    [    0.000015] Switching to timer-based delay loop, resolution 169ns
    [    0.000327] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
    [    0.000334] OMAP clocksource: 32k_counter at 32768 Hz
    [    0.000788] Console: colour dummy device 80x30
    [    0.000805] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
    [    0.000811] This ensures that you still see kernel messages. Please
    [    0.000817] update your kernel commandline.
    [    0.000829] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016)
    [    0.000843] pid_max: default: 32768 minimum: 301
    [    0.000934] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.000944] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001476] Initializing cgroup subsys io
    [    0.001493] Initializing cgroup subsys memory
    [    0.001517] Initializing cgroup subsys devices
    [    0.001529] Initializing cgroup subsys freezer
    [    0.001540] Initializing cgroup subsys perf_event
    [    0.001551] Initializing cgroup subsys pids
    [    0.001579] CPU: Testing write buffer coherency: ok
    [    0.001775] /cpus/cpu@0 missing clock-frequency property
    [    0.001790] /cpus/cpu@1 missing clock-frequency property
    [    0.001800] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [    0.001840] Setting up static identity map for 0x80008340 - 0x800083a0
    [    0.080064] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [    0.080135] Brought up 2 CPUs
    [    0.080149] SMP: Total of 2 processors activated (23.60 BogoMIPS).
    [    0.080156] CPU: All CPU(s) started in SVC mode.
    [    0.081192] devtmpfs: initialized
    [    0.111040] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
    [    0.112025] omap_hwmod: l3_main_2 using broken dt data from ocp
    [    0.310748] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.314458] pinctrl core: initialized pinctrl subsystem
    [    0.315315] NET: Registered protocol family 16
    [    0.316248] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.340278] cpuidle: using governor ladder
    [    0.370303] cpuidle: using governor menu
    [    0.378533] OMAP GPIO hardware version 0.1
    [    0.382634] GPIO line 161 (radio_rst) hogged as output/low
    [    0.414523] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [    0.414534] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.415009] omap4_sram_init:Unable to allocate sram needed to handle errata I688
    [    0.415018] omap4_sram_init:Unable to get sram pool needed to handle errata I688
    [    0.415505] OMAP DMA hardware revision 0.0
    [    0.461690] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
    [    0.462936] edma 43300000.edma: memcpy is disabled
    [    0.467692] edma 43300000.edma: TI EDMA DMA engine driver
    [    0.471903] omap-iommu 40d01000.mmu: 40d01000.mmu registered
    [    0.472083] omap-iommu 40d02000.mmu: 40d02000.mmu registered
    [    0.472245] omap-iommu 58882000.mmu: 58882000.mmu registered
    [    0.472403] omap-iommu 55082000.mmu: 55082000.mmu registered
    [    0.472703] omap-iommu 41501000.mmu: 41501000.mmu registered
    [    0.472889] omap-iommu 41502000.mmu: 41502000.mmu registered
    [    0.474884] SCSI subsystem initialized
    [    0.476142] ======palmas_i2c_probe:526========
    [    0.476159] ======palmas_i2c_probe:559, features=0x0========
    [    0.476464] palmas 0-0058: IRQ missing: skipping irq request
    [    0.491206] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0
    [    0.562945] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
    [    0.563584] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
    [    0.563950] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
    [    0.564309] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
    [    0.564683] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
    [    0.564902] media: Linux media interface: v0.10
    [    0.564958] Linux video capture interface: v2.00
    [    0.564997] pps_core: LinuxPPS API ver. 1 registered
    [    0.565003] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.565026] PTP clock support registered
    [    0.565051] EDAC MC: Ver: 3.0.0
    [    0.565807] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
    [    0.566099] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
    [    0.566445] Advanced Linux Sound Architecture Driver Initialized.
    [    0.567340] clocksource: Switched to clocksource arch_sys_counter
    [    0.578102] NET: Registered protocol family 2
    [    0.578596] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.578659] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.578784] TCP: Hash tables configured (established 8192 bind 8192)
    [    0.578830] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [    0.578863] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [    0.579072] NET: Registered protocol family 1
    [    0.579335] RPC: Registered named UNIX socket transport module.
    [    0.579345] RPC: Registered udp transport module.
    [    0.579351] RPC: Registered tcp transport module.
    [    0.579357] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.580397] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
    [    0.582846] futex hash table entries: 512 (order: 3, 32768 bytes)
    [    0.589537] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.590190] NFS: Registering the id_resolver key type
    [    0.590215] Key type id_resolver registered
    [    0.590222] Key type id_legacy registered
    [    0.590288] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.592263] bounce: pool size: 64 pages
    [    0.592414] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
    [    0.592431] io scheduler noop registered
    [    0.592446] io scheduler deadline registered
    [    0.592480] io scheduler cfq registered (default)
    [    0.597800] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
    [    0.659406] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
    [    0.663036] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 299, base_baud = 3000000) is a 8250
    [    0.663917] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 300, base_baud = 3000000) is a 8250
    [    0.664793] console [ttyS2] disabled
    [    0.664838] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250
    [    1.551629] console [ttyS2] enabled
    [    1.556023] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 302, base_baud = 3000000) is a 8250
    [    1.565752] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 303, base_baud = 3000000) is a 8250
    [    1.575435] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 304, base_baud = 3000000) is a 8250
    [    1.585126] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 305, base_baud = 3000000) is a 8250
    [    1.595260] [drm] Initialized drm 1.1.0 20060810
    [    1.601467] OMAP DSS rev 6.1
    [    1.605234] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
    [    1.627032] brd: module loaded
    [    1.635266] loop: module loaded
    [    1.644960] libphy: Fixed MDIO Bus: probed
    [    1.649677] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
    [    1.656757] e1000: Copyright (c) 1999-2006 Intel Corporation.
    [    1.662607] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    [    1.668478] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    [    1.674482] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k
    [    1.681487] igb: Copyright (c) 2007-2014 Intel Corporation.
    [    1.737371] davinci_mdio 48485000.mdio: davinci mdio revision 1.6
    [    1.743494] davinci_mdio 48485000.mdio: no live phy, scanning all
    [    1.847341] davinci_mdio 48485000.mdio: timed out waiting for user access
    [    1.947340] davinci_mdio 48485000.mdio: timed out waiting for idle
    [    1.953568] davinci_mdio: probe of 48485000.mdio failed with error -5
    [    1.960699] cpsw 48484000.ethernet: Detected MACID = 54:45:38:a7:aa:1e
    [    1.967378] cpsw 48484000.ethernet: cpts: overflow check period 800
    [    1.974347] cpsw 48484000.ethernet: cpsw: Detected MACID = 54:45:38:a7:aa:1f
    [    1.983056] mousedev: PS/2 mouse device common for all mice
    [    1.989285] i2c /dev entries driver
    [    2.007430] tvp5158 1-0058: i2c i/o error: rc == -121 (should be 1)
    [    2.013786] tvp5158 1-0058: i2c i/o error: rc == -121 (should be 1)
    [    2.020121] tvp5158 1-0058: ERROR: Chip id is not TVP5158
    [    2.025658] ov1063x 1-0037: ov1063x Product ID 0 Manufacturer ID 0
    [    2.031886] ov1063x 1-0037: ov1063x 1-0037 sensor driver registered !!
    [    2.039301] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
    [    2.046394] vip 48990000.vip: loading firmware vpdma-1b8.bin
    [    2.057521] vpe 489d0000.vpe: Device registered as /dev/video0
    [    2.067361] vip 48990000.vip: VPDMA firmware loaded
    [    2.072390] vip2-s1: Port B: Using subdev ov1063x 1-0037 for capture
    [    2.079183] vip2-s1: device registered as video1
    [    2.097763] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
    [    2.104148] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
    [    2.110574] omap_hsmmc 480b4000.mmc: no pinctrl state for hs200_1_8v mode
    [    2.117541] evm_3v3_sw: supplied by sysen1
    [    2.157699] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr25 mode
    [    2.164084] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr12 mode
    [    2.170479] omap_hsmmc 480d1000.mmc: no pinctrl state for hs mode
    [    2.208149] ledtrig-cpu: registered to indicate activity on CPUs
    [    2.216249] hwspinlock_user gatemp: requested 10 hwspinlocks
    [    2.237270] pinctrl-single 4a003400.pinmux: pin 4a0036a8.0 already requested by 4806a000.serial; cannot claim for 48460000.mcasp
    [    2.248934] pinctrl-single 4a003400.pinmux: pin-170 (48460000.mcasp) status -22
    [    2.256278] pinctrl-single 4a003400.pinmux: could not request pin 170 (4a0036a8.0) from group mcasp1_pins  on device pinctrl-single
    [    2.268211] davinci-mcasp 48460000.mcasp: Error applying setting, reverse things back
    [    2.276484] davinci-mcasp 48460000.mcasp: Update the bindings to use assigned-clocks!
    [    2.284391] davinci-mcasp 48460000.mcasp: failed to reparent fck
    [    2.290676] pinctrl-single 4a003400.pinmux: pin 4a003700.0 already requested by 4806a000.serial; cannot claim for 48464000.mcasp
    [    2.302305] pinctrl-single 4a003400.pinmux: pin-192 (48464000.mcasp) status -22
    [    2.309687] pinctrl-single 4a003400.pinmux: could not request pin 192 (4a003700.0) from group mcasp2_pins  on device pinctrl-single
    [    2.321575] davinci-mcasp 48464000.mcasp: Error applying setting, reverse things back
    [    2.329828] davinci-mcasp 48464000.mcasp: Update the bindings to use assigned-clocks!
    [    2.337725] davinci-mcasp 48464000.mcasp: failed to reparent fck
    [    2.343977] pinctrl-single 4a003400.pinmux: pin 4a00372c.0 already requested by 4806a000.serial; cannot claim for 48468000.mcasp
    [    2.355607] pinctrl-single 4a003400.pinmux: pin-203 (48468000.mcasp) status -22
    [    2.362959] pinctrl-single 4a003400.pinmux: could not request pin 203 (4a00372c.0) from group mcasp3_pins  on device pinctrl-single
    [    2.374844] davinci-mcasp 48468000.mcasp: Error applying setting, reverse things back
    [    2.383085] davinci-mcasp 48468000.mcasp: Update the bindings to use assigned-clocks!
    [    2.390983] davinci-mcasp 48468000.mcasp: failed to reparent fck
    [    2.397236] pinctrl-single 4a003400.pinmux: pin 4a003734.0 already requested by 4806a000.serial; cannot claim for 4846c000.mcasp
    [    2.408870] pinctrl-single 4a003400.pinmux: pin-205 (4846c000.mcasp) status -22
    [    2.416213] pinctrl-single 4a003400.pinmux: could not request pin 205 (4a003734.0) from group mcasp4_pins  on device pinctrl-single
    [    2.428097] davinci-mcasp 4846c000.mcasp: Error applying setting, reverse things back
    [    2.436336] davinci-mcasp 4846c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.444233] davinci-mcasp 4846c000.mcasp: failed to reparent fck
    [    2.450499] pinctrl-single 4a003400.pinmux: pin 4a003720.0 already requested by 4806a000.serial; cannot claim for 4847c000.mcasp
    [    2.462128] pinctrl-single 4a003400.pinmux: pin-200 (4847c000.mcasp) status -22
    [    2.469480] pinctrl-single 4a003400.pinmux: could not request pin 200 (4a003720.0) from group mcasp8_pins  on device pinctrl-single
    [    2.481364] davinci-mcasp 4847c000.mcasp: Error applying setting, reverse things back
    [    2.489611] davinci-mcasp 4847c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.497508] davinci-mcasp 4847c000.mcasp: failed to reparent fck
    [    2.504692] NET: Registered protocol family 10
    [    2.519972] sit: IPv6 over IPv4 tunneling driver
    [    2.525148] NET: Registered protocol family 17
    [    2.529873] Key type dns_resolver registered
    [    2.534292] omap_voltage_late_init: Voltage driver support not added
    [    2.541209] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    2.548563] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    2.554817] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    2.561455] Power Management for TI OMAP4+ devices.
    [    2.566591] Registering SWP/SWPB emulation handler
    [    2.574136] dmm 4e000000.dmm: initialized all PAT entries
    [    2.601001] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [    2.607679] [drm] No driver support for vblank timestamp query.
    [    2.624846] [drm] Enabling DMM ywrap scrolling
    [    2.680497] mmc0: MAN_BKOPS_EN bit is not set
    [    2.682910] mmc0: switch to bus width 1 failed
    [    2.699844] Console: switching to colour frame buffer device 240x67
    [    2.729767] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
    [    2.745328] mmc0: new high speed MMC card at address 0001
    [    2.761270] mmcblk0: mmc0:0001 R1J55A 7.28 GiB
    [    2.768647] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
    [    2.776079] mmcblk0boot0: mmc0:0001 R1J55A partition 1 128 KiB
    [    2.782184] mmcblk0boot1: mmc0:0001 R1J55A partition 2 128 KiB
    [    2.789519] asoc-simple-card-mcasp1 sound@1: bt-sco-pcm-mcasp1 <-> 48460000.mcasp mapping ok
    [    2.798021] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    2.807739] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPLOUT
    [    2.817587] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    2.827021] mmcblk0: retrying using single block read
    [    2.832138] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.841761] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPROUT
    [    2.849575] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.859358] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    2.868642] blk_update_request: I/O error, dev mmcblk0, sector 0
    [    2.868655] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for LLOUT
    [    2.868662] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.868667] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for RLOUT
    [    2.868672] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.868677] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3L
    [    2.868682] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.868687] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3R
    [    2.868692] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.868697] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for Mic Bias
    [    2.868701] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.868707] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1L
    [    2.868712] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.868717] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1R
    [    2.868722] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.880987] asoc-simple-card-mcasp2 sound@2: bt-sco-pcm-mcasp2 <-> 48464000.mcasp mapping ok
    [    2.880996] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPLOUT
    [    2.881001] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.881006] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPROUT
    [    2.881011] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.881016] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for LLOUT
    [    2.881022] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.881028] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for RLOUT
    [    2.881033] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.881038] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3L
    [    2.881043] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.881048] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3R
    [    2.881053] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.881058] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for Mic Bias
    [    2.881063] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.881068] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1L
    [    2.881073] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.881077] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1R
    [    2.881082] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.883098] asoc-simple-card-mcasp3 sound@3: bt-sco-pcm-mcasp3 <-> 48468000.mcasp mapping ok
    [    2.883107] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPLOUT
    [    2.883112] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.883118] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPROUT
    [    2.883122] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.883127] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for LLOUT
    [    2.883132] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.883138] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for RLOUT
    [    2.883143] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.883148] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3L
    [    2.883153] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.883158] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3R
    [    2.883162] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.883167] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for Mic Bias
    [    2.883172] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.883177] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1L
    [    2.883182] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.883187] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1R
    [    2.883191] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.885254] asoc-simple-card-mcasp4 sound@4: bt-sco-pcm-mcasp4 <-> 4846c000.mcasp mapping ok
    [    2.885262] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPLOUT
    [    2.885268] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.885273] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPROUT
    [    2.885279] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.885284] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for LLOUT
    [    2.885290] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.885295] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for RLOUT
    [    2.885300] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.885305] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3L
    [    2.885310] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.885314] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3R
    [    2.885319] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.885324] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for Mic Bias
    [    2.885328] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.885334] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1L
    [    2.885339] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.885344] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1R
    [    2.885349] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.887766] asoc-simple-card-mcasp8 sound@8: bt-sco-pcm-mcasp8 <-> 4847c000.mcasp mapping ok
    [    2.887775] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPLOUT
    [    2.887780] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.887786] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPROUT
    [    2.887791] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.887796] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for LLOUT
    [    2.887801] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.887806] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for RLOUT
    [    2.887811] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.887816] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3L
    [    2.887820] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.887825] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3R
    [    2.887829] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.887834] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for Mic Bias
    [    2.887839] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.887844] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1L
    [    2.887848] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.887853] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1R
    [    2.887858] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.888877] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    2.888880] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    2.888940] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    2.898610] hctosys: unable to open rtc device (rtc0)
    [    2.913245] aic_dvdd: disabling
    [    2.932189] ldousb: disabling
    [    2.982904] ALSA device list:
    [    2.982908]   #0: DRA7xx-EVM-MCASP1
    [    2.982911]   #1: DRA7xx-EVM-MCASP2
    [    2.982913]   #2: DRA7xx-EVM-MCASP3
    [    2.982916]   #3: DRA7xx-EVM-MCASP4
    [    2.982918]   #4: DRA7xx-EVM-MCASP8
    [    3.686889] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    3.696185] blk_update_request: I/O error, dev mmcblk0, sector 1
    [    3.702414] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    3.711698] blk_update_request: I/O error, dev mmcblk0, sector 2
    [    3.717930] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    3.727190] blk_update_request: I/O error, dev mmcblk0, sector 3
    [    3.733426] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    3.742704] blk_update_request: I/O error, dev mmcblk0, sector 4
    [    3.748936] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    3.758212] blk_update_request: I/O error, dev mmcblk0, sector 5
    [    3.764427] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    3.773700] blk_update_request: I/O error, dev mmcblk0, sector 6
    [    3.779925] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    3.789201] blk_update_request: I/O error, dev mmcblk0, sector 7
    [    3.795236] Buffer I/O error on dev mmcblk0, logical block 0, async page read
    [    3.802602] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    3.811756] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    3.821206] mmcblk0: retrying using single block read
    [    3.826458] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    3.835732] blk_update_request: I/O error, dev mmcblk0, sector 0
    [    3.841953] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    3.851230] blk_update_request: I/O error, dev mmcblk0, sector 1
    [    3.857446] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    3.866885] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    3.876337] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    3.885797] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    3.895249] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    3.904704] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    3.913983] Buffer I/O error on dev mmcblk0, logical block 0, async page read
    [    3.921172]  mmcblk0: unable to read partition table
    [    3.927519] Waiting for root device PARTUUID=bddb4f41-02...
    [    3.927595] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    3.927599] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    3.927652] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    3.990491] mmc1: MAN_BKOPS_EN bit is not set
    [    4.099283] mmc1: new DDR MMC card at address 0001
    [    4.104543] mmcblk1: mmc1:0001 R1J55A 7.28 GiB
    [    4.119371] mmcblk1boot0: mmc1:0001 R1J55A partition 1 128 KiB
    [    4.135483] mmcblk1boot1: mmc1:0001 R1J55A partition 2 128 KiB
    [    4.142371]  mmcblk1: p1 p2
    [    4.146693] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    4.153034] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    4.159341] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    4.197251] EXT4-fs (mmcblk1p2): recovery complete
    [    4.202499] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
    [    4.210690] VFS: Mounted root (ext4 filesystem) on device 179:50.
    [    4.218233] devtmpfs: mounted
    [    4.221434] Freeing unused kernel memory: 372K (c0c07000 - c0c64000)
    [    4.227856] This architecture does not have kernel memory protection.
    [    4.241563] mmc2: host does not support reading read-only switch, assuming write-enable
    [    4.249694] mmc2: new SDHC card at address 0001
    [    4.254638] mmcblk2: mmc2:0001 SD4GB 3.64 GiB
    [    4.260955]  mmcblk2: p1 p2
    [    4.264566] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    4.270865] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    4.270929] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    INIT: version 2.88 booting
    Starting udev
    [    4.552320] udevd[129]: starting version 182
    [    4.731554] omap-rproc 58820000.ipu: assigned reserved memory node ipu1_cma@9d000000
    [    4.857486]  remoteproc0: 58820000.ipu is available
    [    4.862418]  remoteproc0: Note: remoteproc is still under development and considered experimental.
    [    5.037117]  remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.201575]  remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2
    [    5.207640] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.207645] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.207709] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.229078] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@95800000
    [    5.337466]  remoteproc1: 55020000.ipu is available
    [    5.342383]  remoteproc1: Note: remoteproc is still under development and considered experimental.
    [    5.489896]  remoteproc0: failed to load dra7-ipu1-fw.xem4
    [    5.500558]  remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.583597] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@99000000
    [    5.583681] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.583686] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.583748] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.639004]  remoteproc2: 40800000.dsp is available
    [    5.643951] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    5.653192] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0x0
    [    5.653198] mmcblk0: retrying using single block read
    [    5.668254] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0x0
    [    5.678210] mmcblk0: error -84 transferring data, sector 15269761, nr 7, cmd response 0x900, card status 0x0
    [    5.719653] CAN device driver interface
    [    5.737930] mmcblk0: error -84 transferring data, sector 15269762, nr 6, cmd response 0x900, card status 0x0
    [    5.745950]  remoteproc2: Note: remoteproc is still under development and considered experimental.
    [    5.745955]  remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.747055] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9f000000
    [    5.747112]  remoteproc3: 41000000.dsp is available
    [    5.747115]  remoteproc3: Note: remoteproc is still under development and considered experimental.
    [    5.747118]  remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.751380] pinctrl-single 4a003400.pinmux: pin 4a0037d0.0 already requested by 4806a000.serial; cannot claim for 4ae3c000.can
    [    5.751388] pinctrl-single 4a003400.pinmux: pin-244 (4ae3c000.can) status -22
    [    5.751396] pinctrl-single 4a003400.pinmux: could not request pin 244 (4a0037d0.0) from group dcan1_pins_sleep  on device pinctrl-single
    [    5.751400] c_can_platform 4ae3c000.can: Error applying setting, reverse things back
    [    5.752239] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=367)
    [    5.757730] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.757734] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.757795] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.784380]  remoteproc1: registered virtio0 (type 7)
    [    5.784988]  remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2
    [    5.784994]  remoteproc3: failed to load dra7-dsp2-fw.xe66
    [    5.787759]  remoteproc2: registered virtio1 (type 7)
    [    5.814972] [drm] Initialized pvr 1.14.3699939 20110701 on minor 1
    [    5.816385] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.816390] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.816454] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.915905] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20
    [    5.916023] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
    [    5.923383] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.923388] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.923445] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.018191] mmcblk0: error -84 transferring data, sector 15269763, nr 5, cmd response 0x900, card status 0x0
    [    6.018559] mmcblk0: error -84 transferring data, sector 15269764, nr 4, cmd response 0x900, card status 0x0
    [    6.018945] mmcblk0: error -84 transferring data, sector 15269765, nr 3, cmd response 0x900, card status 0x0
    [    6.018972] alg: skcipher: setkey failed on test 5 for ecb-des-omap: flags=100
    [    6.019921] mmcblk0: error -84 transferring data, sector 15269766, nr 2, cmd response 0x900, card status 0x0
    [    6.020140] mmcblk0: error -84 transferring data, sector 15269767, nr 1, cmd response 0x900, card status 0x0
    [    6.020268] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    6.020340] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.038687] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0xb00
    [    6.038692] mmcblk0: retrying using single block read
    [    6.039368] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0x0
    [    6.041806] mmcblk0: error -84 transferring data, sector 15269761, nr 7, cmd response 0x900, card status 0x0
    [    6.041968] mmcblk0: error -84 transferring data, sector 15269762, nr 6, cmd response 0x900, card status 0x0
    [    6.042083] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    6.042145] mmcblk0: error -84 transferring data, sector 15269763, nr 5, cmd response 0x900, card status 0x0
    [    6.042296] mmcblk0: error -84 transferring data, sector 15269764, nr 4, cmd response 0x900, card status 0x0
    [    6.042459] mmcblk0: error -84 transferring data, sector 15269765, nr 3, cmd response 0x900, card status 0x0
    [    6.042614] mmcblk0: error -84 transferring data, sector 15269766, nr 2, cmd response 0x900, card status 0x0
    [    6.042780] mmcblk0: error -84 transferring data, sector 15269767, nr 1, cmd response 0x900, card status 0x0
    [    6.042790] Buffer I/O error on dev mmcblk0, logical block 1908720, async page read
    [    6.043014] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.043093] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0xb00
    [    6.043097] mmcblk0: retrying using single block read
    [    6.043256] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0x0
    [    6.043418] mmcblk0: error -84 transferring data, sector 15269873, nr 7, cmd response 0x900, card status 0x0
    [    6.043545] mmcblk0: error -84 transferring data, sector 15269874, nr 6, cmd response 0x900, card status 0x0
    [    6.043701] mmcblk0: error -84 transferring data, sector 15269875, nr 5, cmd response 0x900, card status 0x0
    [    6.043829] mmcblk0: error -84 transferring data, sector 15269876, nr 4, cmd response 0x900, card status 0x0
    [    6.043964] mmcblk0: error -84 transferring data, sector 15269877, nr 3, cmd response 0x900, card status 0x0
    [    6.044091] mmcblk0: error -84 transferring data, sector 15269878, nr 2, cmd response 0x900, card status 0x0
    [    6.044250] mmcblk0: error -84 transferring data, sector 15269879, nr 1, cmd response 0x900, card status 0x0
    [    6.044420] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.044483] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0xb00
    [    6.044487] mmcblk0: retrying using single block read
    [    6.044610] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0x0
    [    6.044738] mmcblk0: error -84 transferring data, sector 15269873, nr 7, cmd response 0x900, card status 0x0
    [    6.044861] mmcblk0: error -84 transferring data, sector 15269874, nr 6, cmd response 0x900, card status 0x0
    [    6.044985] mmcblk0: error -84 transferring data, sector 15269875, nr 5, cmd response 0x900, card status 0x0
    [    6.045111] mmcblk0: error -84 transferring data, sector 15269876, nr 4, cmd response 0x900, card status 0x0
    [    6.045236] mmcblk0: error -84 transferring data, sector 15269877, nr 3, cmd response 0x900, card status 0x0
    [    6.045368] mmcblk0: error -84 transferring data, sector 15269878, nr 2, cmd response 0x900, card status 0x0
    [    6.045493] mmcblk0: error -84 transferring data, sector 15269879, nr 1, cmd response 0x900, card status 0x0
    [    6.045500] Buffer I/O error on dev mmcblk0, logical block 1908734, async page read
    [    6.045705] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.045760] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    6.045763] mmcblk0: retrying using single block read
    [    6.045945] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    6.046129] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    6.046307] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    6.046492] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    6.046674] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    6.046850] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    6.047024] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    6.047198] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    6.047379] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.047430] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    6.047434] mmcblk0: retrying using single block read
    [    6.047615] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    6.047794] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    6.047970] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    6.048144] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    6.048319] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    6.048498] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    6.048674] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    6.048848] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    6.048856] Buffer I/O error on dev mmcblk0, logical block 0, async page read
    [    6.049125] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.049173] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    6.049176] mmcblk0: retrying using single block read
    [    6.049355] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    [    6.049537] mmcblk0: error -84 transferring data, sector 9, nr 7, cmd response 0x900, card status 0x0
    [    6.049718] mmcblk0: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    [    6.049900] mmcblk0: error -84 transferring data, sector 11, nr 5, cmd response 0x900, card status 0x0
    [    6.050082] mmcblk0: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    [    6.050264] mmcblk0: error -84 transferring data, sector 13, nr 3, cmd response 0x900, card status 0x0
    [    6.057238] mmcblk0: error -84 transferring data, sector 14, nr 2, cmd response 0x900, card status 0x0
    [    6.058705] mmcblk0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    [    6.058715] Buffer I/O error on dev mmcblk0, logical block 1, async page read
    [    6.059005] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 52 printk messages dropped ** [    6.065593] mmcblk0: error -84 transferring data, sector 15269882, nr 6, cmd response 0x900, card status 0x0
    ** 18 printk messages dropped ** [    6.069256] mmcblk0: retrying using single block read
    ** 3 printk messages dropped ** [    6.069802] mmcblk0: error -84 transferring data, sector 15269827, nr 5, cmd response 0x900, card status 0x0
    ** 14 printk messages dropped ** [    6.071657] mmcblk0: error -84 transferring data, sector 15269879, nr 1, cmd response 0x900, card status 0x0
    ** 12 printk messages dropped ** [    6.073786] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    6.073789] mmcblk0: retrying using single block read
    ** 7 printk messages dropped ** [    6.075318] mmcblk0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    ** 11 printk messages dropped ** [    6.116558] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    6.120261] mmcblk0: retrying using single block read
    ** 22 printk messages dropped ** [    6.123844] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 17 printk messages dropped ** [    6.126763] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 7 printk messages dropped ** [    6.128098] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    ** 74 printk messages dropped ** [    6.147089] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 129 printk messages dropped ** [    6.169535] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 118 printk messages dropped ** [    6.219804] mmcblk0: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 33 printk messages dropped ** [    6.225384] mmcblk0: error -84 transferring data, sector 61, nr 3, cmd response 0x900, card status 0x0
    ** 38 printk messages dropped ** [    6.249558] mmcblk0: error -84 transferring data, sector 120, nr 8, cmd response 0x900, card status 0x0
    ** 31 printk messages dropped ** [    6.308644] mmcblk0: retrying using single block read
    ** 20 printk messages dropped ** [    6.435325] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    ** 45 printk messages dropped ** [    6.615830] mmcblk0: error -84 transferring data, sector 56, nr 8, cmd response 0x900, card status 0x0
    ** 28 printk messages dropped ** [    6.679610] mmcblk0: error -84 transferring data, sector 127, nr 1, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    6.723007] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 31 printk messages dropped ** [    6.765942] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
    ** 20 printk messages dropped ** [    6.781631] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    6.786248] mmcblk0: error -84 transferring data, sector 134, nr 2, cmd response 0x900, card status 0x0
    ** 34 printk messages dropped ** [    6.871495] mmcblk0: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    ** 31 printk messages dropped ** [    6.926403] mmcblk0: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    ** 27 printk messages dropped ** [    6.948468] mmcblk0: retrying using single block read
    ** 21 printk messages dropped ** [    6.952079] mmcblk0: retrying using single block read
    ** 21 printk messages dropped ** [    6.955778] mmcblk0: retrying using single block read
    ** 26 printk messages dropped ** [    6.969841] mmcblk0: error -84 transferring data, sector 260, nr 4, cmd response 0x900, card status 0x0
    ** 42 printk messages dropped ** [    6.976413] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 34 printk messages dropped ** [    6.991654] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 31 printk messages dropped ** [    7.005727] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.010401] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 30 printk messages dropped ** [    7.015684] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.025203] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 25 printk messages dropped ** [    7.029420] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.048313] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.052102] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.068499] mmcblk0: retrying using single block read
    ** 15 printk messages dropped ** [    7.079640] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.118820] mmcblk0: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.136739] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.156549] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 21 printk messages dropped ** [    7.166335] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.192523] mmcblk0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.210238] mmcblk0: retrying using single block read
    ** 16 printk messages dropped ** [    7.213104] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.217209] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    7.220633] mmcblk0: retrying using single block read
    ** 17 printk messages dropped ** [    7.223560] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.227328] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.231222] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.235646] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.240086] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.244258] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.248282] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.252922] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.266619] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 30 printk messages dropped ** [    7.283300] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.296234] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.308987] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.317826] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x3b
    ** 19 printk messages dropped ** [    7.328665] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    7.339639] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    7.375730] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.387996] mmcblk0boot0: retrying using single block read
    ** 15 printk messages dropped ** [    7.396588] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.410223] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.422433] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.434769] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.448173] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.457492] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.470932] mmcblk0boot1: retrying using single block read
    ** 19 printk messages dropped ** [    7.485725] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.496512] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.507213] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.515723] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.528630] hub 2-0:1.0: 1 port detected
    ** 14 printk messages dropped ** [    7.530561] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.542362] hub 3-0:1.0: USB hub found
    ** 13 printk messages dropped ** [    7.545214] mmcblk0boot0: retrying using single block read
    ** 16 printk messages dropped ** [    7.554414] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.564891] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.580896] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.593840] mmcblk0boot0: retrying using single block read
    ** 15 printk messages dropped ** [    7.602451] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.614720] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.626842] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.640057] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.652295] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.665124] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.677741] mmcblk0boot0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.689811] mmcblk0boot0: error -84 transferring data, sector 25, nr 7, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.703497] mmcblk0boot0: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.715515] mmcblk0boot0: error -84 transferring data, sector 62, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.727552] mmcblk0boot0: retrying using single block read
    ** 15 printk messages dropped ** [    7.736586] mmcblk0boot1: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.749156] mmcblk0boot1: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.760599] mmcblk0boot1: retrying using single block read
    ** 15 printk messages dropped ** [    7.769047] mmcblk0boot1: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.781646] mmcblk0boot1: error -84 transferring data, sector 63, nr 1, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.794372] mmcblk0boot0: error -84 transferring data, sector 120, nr 8, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.806983] mmcblk0boot0: error -84 transferring data, sector 123, nr 5, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.819066] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.831755] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    7.842638] mmcblk0boot0: retrying using single block read
    ** 16 printk messages dropped ** [    7.851671] mmcblk0boot0: error -84 transferring data, sector 61, nr 3, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.864298] mmcblk0boot1: error -84 transferring data, sector 127, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.875772] mmcblk0boot1: retrying using single block read
    ** 18 printk messages dropped ** [    7.881972] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.892885] mmcblk0boot1: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.906077] mmcblk0boot1: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.919273] mmcblk0boot0: error -84 transferring data, sector 127, nr 1, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.930777] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 28 printk messages dropped ** [    7.944954] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.957215] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.970087] mmcblk0boot1: error -84 transferring data, sector 56, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    7.983366] mmcblk0boot1: error -84 transferring data, sector 123, nr 5, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.994863] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    8.007689] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    8.019354] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    8.033500] mmcblk0boot0: error -84 transferring data, sector 131, nr 5, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    8.046346] mmcblk0boot0: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    8.058582] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 22 printk messages dropped ** [    8.069704] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    ** 10 printk messages dropped ** [    8.075243] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    ** 21 printk messages dropped ** [    8.086308] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    8.100486] mmcblk0boot1: error -84 transferring data, sector 131, nr 5, cmd response 0x900, card status 0x0
    ** 16 printk messages dropped ** [    8.109046] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0xb00
    [    8.109050] mmcblk0boot1: retrying using single block read
    [    8.109723] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0x0
    [    8.110328] mmcblk0boot1: error -84 transferring data, sector 17, nr 7, cmd response 0x900, card status 0x0
    [    8.110932] mmcblk0boot1: error -84 transferring data, sector 18, nr 6, cmd response 0x900, card status 0x0
    [    8.111541] mmcblk0boot1: error -84 transferring data, sector 19, nr 5, cmd response 0x900, card status 0x0
    [    8.112142] mmcblk0boot1: error -84 transferring data, sector 20, nr 4, cmd response 0x900, card status 0x0
    [    8.112741] mmcblk0boot1: error -84 transferring data, sector 21, nr 3, cmd response 0x900, card status 0x0
    [    8.113340] mmcblk0boot1: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    [    8.113935] mmcblk0boot1: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    [    8.114514] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.114567] mmcblk0boot1: error -84 transferring data, sector 128, nr 8, cmd response 0x900, card status 0xb00
    [    8.114571] mmcblk0boot1: retrying using single block read
    [    8.115246] mmcblk0boot1: error -84 transferring data, sector 128, nr 8, cmd response 0x900, card status 0x0
    [    8.115851] mmcblk0boot1: error -84 transferring data, sector 129, nr 7, cmd response 0x900, card status 0x0
    [    8.116455] mmcblk0boot1: error -84 transferring data, sector 130, nr 6, cmd response 0x900, card status 0x0
    [    8.117058] mmcblk0boot1: error -84 transferring data, sector 131, nr 5, cmd response 0x900, card status 0x0
    [    8.117673] mmcblk0boot1: error -84 transferring data, sector 132, nr 4, cmd response 0x900, card status 0x0
    [    8.118270] mmcblk0boot1: error -84 transferring data, sector 133, nr 3, cmd response 0x900, card status 0x0
    [    8.118866] mmcblk0boot1: error -84 transferring data, sector 134, nr 2, cmd response 0x900, card status 0x0
    [    8.119473] mmcblk0boot1: error -84 transferring data, sector 135, nr 1, cmd response 0x900, card status 0x0
    [    8.120041] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.120100] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.120103] mmcblk0boot1: retrying using single block read
    [    8.120785] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.121392] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.122001] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.122603] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.123209] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.123815] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.124412] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.125013] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.125582] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.125644] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.125648] mmcblk0boot1: retrying using single block read
    [    8.126325] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.126937] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.127554] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.128150] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.128754] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.129355] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.129952] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.130550] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.131123] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.131184] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.131188] mmcblk0boot1: retrying using single block read
    [    8.131867] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.132473] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.133079] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.133680] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.134282] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.134882] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.135480] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.136079] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.136647] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.136707] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.136711] mmcblk0boot1: retrying using single block read
    [    8.137396] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.138002] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.138604] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.139210] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.139808] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.140407] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.141006] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.141609] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.142178] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.142236] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.142240] mmcblk0boot1: retrying using single block read
    [    8.142920] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.143525] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.144132] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.144739] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.145344] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.145946] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.146548] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.147149] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.147723] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.147782] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.147786] mmcblk0boot1: retrying using single block read
    [    8.148459] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.149071] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.149675] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.150283] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.150888] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.151488] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.152086] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.152682] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.153859] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.153911] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.153914] mmcblk0boot0: retrying using single block read
    [    8.154589] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.155196] mmcblk0boot0: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.155800] mmcblk0boot0: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.156405] mmcblk0boot0: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.157004] mmcblk0boot0: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.157611] mmcblk0boot0: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.158210] mmcblk0boot0: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.158807] mmcblk0boot0: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.159380] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.159434] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.159438] mmcblk0boot0: retrying using single block read
    [    8.160115] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.160722] mmcblk0boot0: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.161324] mmcblk0boot0: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.161930] mmcblk0boot0: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.162532] mmcblk0boot0: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.163132] mmcblk0boot0: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.163736] mmcblk0boot0: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.164331] mmcblk0boot0: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.164908] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.164962] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.164965] mmcblk0boot0: retrying using single block read
    [    8.165639] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.166243] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.166849] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.167457] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.168057] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.168660] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.169254] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.169857] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.170428] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.170481] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.170485] mmcblk0boot0: retrying using single block read
    [    8.171159] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.171768] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.172372] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.172975] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.173577] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.174179] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.174774] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.175373] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.175943] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.175999] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.176001] mmcblk0boot0: retrying using single block read
    [    8.176674] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.177279] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.177882] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.178485] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.179089] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.179689] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.180284] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.180882] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.181456] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.181510] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.181513] mmcblk0boot0: retrying using single block read
    [    8.182188] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.182793] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.183395] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.183997] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.184602] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.185204] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.185801] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.186401] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.186972] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.187023] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.187026] mmcblk0boot0: retrying using single block read
    [    8.187713] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.188310] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.188913] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.189516] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.190118] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.190717] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.191313] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.191911] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.192484] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.192537] mmcblk0boot0: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0xb00
    [    8.192541] mmcblk0boot0: retrying using single block read
    [    8.193221] mmcblk0boot0: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0x0
    [    8.193827] mmcblk0boot0: error -84 transferring data, sector 17, nr 7, cmd response 0x900, card status 0x0
    [    8.194431] mmcblk0boot0: error -84 transferring data, sector 18, nr 6, cmd response 0x900, card status 0x0
    [    8.195035] mmcblk0boot0: error -84 transferring data, sector 19, nr 5, cmd response 0x900, card status 0x0
    [    8.195634] mmcblk0boot0: error -84 transferring data, sector 20, nr 4, cmd response 0x900, card status 0x0
    [    8.196236] mmcblk0boot0: error -84 transferring data, sector 21, nr 3, cmd response 0x900, card status 0x0
    [    8.196838] mmcblk0boot0: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    [    8.197436] mmcblk0boot0: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    [    8.198006] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.198060] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.198063] mmcblk0boot0: retrying using single block read
    [    8.198736] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.199342] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.199946] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.200550] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.201151] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.201749] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.202347] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.202946] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.203519] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.203573] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.203576] mmcblk0boot0: retrying using single block read
    [    8.204248] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.204854] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.205455] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.206062] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.206660] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.207264] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.208832] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.209251] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.209807] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.209867] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.209870] mmcblk0boot0: retrying using single block read
    [    8.210550] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.211157] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.211758] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.212361] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.212958] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.213563] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.214165] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.214759] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.215941] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.215998] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.216001] mmcblk0boot1: retrying using single block read
    [    8.216681] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.217290] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.217904] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.218498] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.219100] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.219703] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.220304] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.220902] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.221477] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.221533] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.221537] mmcblk0boot1: retrying using single block read
    [    8.222212] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.222823] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.223427] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.224035] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.224635] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.225234] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.225835] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.226431] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.227005] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.227062] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.227065] mmcblk0boot1: retrying using single block read
    [    8.227741] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.228346] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.228951] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.229553] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.230160] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.230760] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.231357] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.231955] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.232527] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.232580] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.232583] mmcblk0boot1: retrying using single block read
    [    8.233258] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.233862] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.234468] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.235071] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.235669] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.236269] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.236867] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.237481] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.238039] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.238093] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.238097] mmcblk0boot1: retrying using single block read
    [    8.238770] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.239380] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.239981] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.240589] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.241187] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.241790] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.242391] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.242986] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.243558] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.243612] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.243615] mmcblk0boot1: retrying using single block read
    [    8.244292] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.244899] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.245505] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.246106] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.246705] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.247302] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.247907] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.248501] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.249074] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.249129] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.249131] mmcblk0boot1: retrying using single block read
    [    8.249804] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.250410] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.251016] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.251618] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.252220] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.252816] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.253412] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.254010] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.254585] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.254639] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.254642] mmcblk0boot1: retrying using single block read
    [    8.255315] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.255919] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.256528] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.257133] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.257741] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.258338] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.258934] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.259533] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.260106] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.260159] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0xb00
    [    8.260163] mmcblk0boot1: retrying using single block read
    [    8.260836] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0x0
    [    8.261446] mmcblk0boot1: error -84 transferring data, sector 17, nr 7, cmd response 0x900, card status 0x0
    [    8.262055] mmcblk0boot1: error -84 transferring data, sector 18, nr 6, cmd response 0x900, card status 0x0
    [    8.262659] mmcblk0boot1: error -84 transferring data, sector 19, nr 5, cmd response 0x900, card status 0x0
    [    8.263261] mmcblk0boot1: error -84 transferring data, sector 20, nr 4, cmd response 0x900, card status 0x0
    [    8.263862] mmcblk0boot1: error -84 transferring data, sector 21, nr 3, cmd response 0x900, card status 0x0
    [    8.264461] mmcblk0boot1: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    [    8.265058] mmcblk0boot1: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    [    8.265631] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.265684] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.265687] mmcblk0boot1: retrying using single block read
    [    8.266360] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.266965] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.267569] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.268172] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.268768] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.269370] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.269966] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.270561] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.271134] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.271189] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.271192] mmcblk0boot1: retrying using single block read
    [    8.271864] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.272468] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.273073] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.273675] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.274273] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.274876] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.275473] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.276075] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.277254] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.277310] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.277313] mmcblk0boot0: retrying using single block read
    [    8.277990] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.278597] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.279203] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.279808] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.280404] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.281009] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.281608] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.282203] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.282775] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.282829] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.282832] mmcblk0boot0: retrying using single block read
    [    8.283509] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.284115] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.284717] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.285317] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.285918] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.286518] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.287112] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.287714] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.288281] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.288336] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.288340] mmcblk0boot0: retrying using single block read
    [    8.289015] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.289620] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.290223] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.290826] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.291425] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.292026] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.292625] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.293220] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.293797] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.293851] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.293854] mmcblk0boot0: retrying using single block read
    [    8.294526] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.295131] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.295735] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.296343] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.296943] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.297561] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.298150] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.298750] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.299316] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.299375] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.299378] mmcblk0boot0: retrying using single block read
    [    8.300056] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.300666] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.301272] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.301874] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.302477] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.303075] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.303673] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.304267] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.304835] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.304896] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.304900] mmcblk0boot0: retrying using single block read
    [    8.305579] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.306185] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.306786] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.307397] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.307993] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.308590] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.309188] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.309783] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.310355] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.310416] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.310419] mmcblk0boot0: retrying using single block read
    [    8.311095] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.311703] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.312305] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.312909] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.313507] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.314111] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.314707] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.315308] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.315874] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.315932] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.315935] mmcblk0boot0: retrying using single block read
    [    8.316614] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.317222] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.317836] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.318431] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.319032] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.319633] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.320235] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.320834] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.321400] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.321457] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.321460] mmcblk0boot0: retrying using single block read
    [    8.322142] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.322751] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.323352] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.323953] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.324556] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.325152] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.325750] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.326346] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.326915] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.326975] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.326978] mmcblk0boot0: retrying using single block read
    [    8.327662] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.328262] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.328866] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.329465] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.330063] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.330662] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.331264] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.331860] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.332430] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.332490] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.332494] mmcblk0boot0: retrying using single block read
    [    8.333172] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.333776] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.334381] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.334986] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.335591] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.336189] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.336789] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.337391] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.338563] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.338615] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.338618] mmcblk0boot1: retrying using single block read
    [    8.339292] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.339902] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.340508] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.341108] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.341713] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.342314] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.342909] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.343505] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.344083] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.344137] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.344140] mmcblk0boot1: retrying using single block read
    [    8.344811] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.345416] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.346020] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.346621] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.347225] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.347829] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.348422] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.349018] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.349592] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.349645] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.349648] mmcblk0boot1: retrying using single block read
    [    8.350320] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.350927] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.351528] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.352129] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.352734] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.353336] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.353932] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.354530] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.355105] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.355159] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.355162] mmcblk0boot1: retrying using single block read
    [    8.355834] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.356443] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.357046] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.357665] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.358260] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.358861] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.359462] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.360058] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.360626] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.360685] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.360688] mmcblk0boot1: retrying using single block read
    [    8.361370] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.361979] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.362581] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.363184] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.363785] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.364381] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.364979] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.365576] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.366143] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.366201] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.366204] mmcblk0boot1: retrying using single block read
    [    8.366883] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.367492] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.368084] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.368687] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.369285] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.369885] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.370481] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.371081] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.371653] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.371707] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.371710] mmcblk0boot1: retrying using single block read
    [    8.372382] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.372988] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.373590] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.374195] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.374793] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.375397] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.375999] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.376592] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.377167] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.377220] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.377224] mmcblk0boot1: retrying using single block read
    [    8.377900] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.378508] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.379111] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.379717] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.380317] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.380916] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.381512] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.382107] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.382684] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.382738] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.382741] mmcblk0boot1: retrying using single block read
    [    8.383413] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.384019] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.384623] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.385223] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.385823] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.386420] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.387020] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.387629] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.388189] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.388248] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.388252] mmcblk0boot1: retrying using single block read
    [    8.388930] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.389534] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.390140] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.390740] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.391339] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.391942] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.392538] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.393140] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.393710] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.393769] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.393772] mmcblk0boot1: retrying using single block read
    [    8.394455] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.395060] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.395664] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.396268] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.396873] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.397483] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.398066] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.398662] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.399837] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.399890] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.399894] mmcblk0boot0: retrying using single block read
    [    8.400570] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.401174] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.401778] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.402378] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.402978] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.403579] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.404175] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.404771] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.405343] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.405397] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.405401] mmcblk0boot0: retrying using single block read
    [    8.406072] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.406679] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.407277] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.407885] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.408483] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.409084] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.409682] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.410279] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.410854] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.410908] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.410911] mmcblk0boot0: retrying using single block read
    [    8.411580] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.412193] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.412794] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.413400] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.414003] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.414603] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.415206] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.415799] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.416373] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.416429] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.416431] mmcblk0boot0: retrying using single block read
    [    8.417106] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.417727] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.418323] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.418926] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.419525] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.420125] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.420721] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.421320] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.421883] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.421941] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.421945] mmcblk0boot0: retrying using single block read
    [    8.422622] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.423228] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.423832] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.424431] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.425031] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.425633] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.426227] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.426825] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.427402] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.427462] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.427465] mmcblk0boot0: retrying using single block read
    [    8.428145] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.428748] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.429351] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.429958] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.430554] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.431159] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.431753] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.432356] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.432927] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.432984] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.432987] mmcblk0boot0: retrying using single block read
    [    8.433670] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.434275] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.434879] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.435485] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.436090] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.436692] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.437288] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.437890] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.438453] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.438508] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.438511] mmcblk0boot0: retrying using single block read
    [    8.439185] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.439794] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.440398] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.440997] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.441599] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.442197] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.442793] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.443390] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.443962] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.444016] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.444019] mmcblk0boot0: retrying using single block read
    [    8.444692] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.445300] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.445904] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.446505] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.447106] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.447708] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.448302] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.448903] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.449475] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.449528] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.449531] mmcblk0boot0: retrying using single block read
    [    8.450204] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.450815] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.451418] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.452024] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.452626] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.453227] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.453825] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.454427] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.454987] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.455040] mmcblk0boot0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    8.455044] mmcblk0boot0: retrying using single block read
    [    8.455709] mmcblk0boot0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    [    8.456305] mmcblk0boot0: error -84 transferring data, sector 9, nr 7, cmd response 0x900, card status 0x0
    [    8.456893] mmcblk0boot0: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    [    8.457500] mmcblk0boot0: error -84 transferring data, sector 11, nr 5, cmd response 0x900, card status 0x0
    [    8.458073] mmcblk0boot0: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    [    8.458661] mmcblk0boot0: error -84 transferring data, sector 13, nr 3, cmd response 0x900, card status 0x0
    [    8.459244] mmcblk0boot0: error -84 transferring data, sector 14, nr 2, cmd response 0x900, card status 0x0
    [    8.459827] mmcblk0boot0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    [    8.461008] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.461060] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.461064] mmcblk0boot1: retrying using single block read
    [    8.461736] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.462343] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.462947] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.463558] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.464154] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.464758] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.465356] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.465954] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.466528] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.466584] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.466588] mmcblk0boot1: retrying using single block read
    [    8.467262] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.467873] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.468479] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.469081] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.469684] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.470284] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.470879] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.471473] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.472052] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.472104] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.472107] mmcblk0boot1: retrying using single block read
    [    8.472781] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.473385] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.473990] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.474590] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.475196] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.475796] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.476392] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.476985] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.477567] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.477630] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.477633] mmcblk0boot1: retrying using single block read
    [    8.478308] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.478912] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.479515] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.480117] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.480717] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.481321] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.481916] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.482517] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.483089] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.483142] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.483145] mmcblk0boot1: retrying using single block read
    [    8.483819] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.484425] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.485034] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.485636] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.486239] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.486840] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.487442] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.488036] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.488610] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.488663] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.488666] mmcblk0boot1: retrying using single block read
    [    8.489342] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.489952] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.490554] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.491156] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.491755] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.492353] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.492951] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.493547] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.494120] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.494174] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.494177] mmcblk0boot1: retrying using single block read
    [    8.494850] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.495454] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.496056] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.496658] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.497256] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.497873] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.498461] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.499061] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.499628] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.499686] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.499690] mmcblk0boot1: retrying using single block read
    [    8.500367] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.500972] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.501575] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.502180] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.502787] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.503383] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.503983] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.504580] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.505153] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.505214] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.505217] mmcblk0boot1: retrying using single block read
    [    8.505899] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.506507] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.507110] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.507726] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.508318] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.508920] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.509516] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.510115] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.510682] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.510740] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.510744] mmcblk0boot1: retrying using single block read
    [    8.511428] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.512031] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.512633] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.513234] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.513834] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.514433] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.515029] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.515628] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.516196] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.516253] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.516256] mmcblk0boot1: retrying using single block read
    [    8.516937] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.517552] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.518140] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.518743] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.519340] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.519939] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.520544] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.521139] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.522316] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.522368] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.522371] mmcblk0boot0: retrying using single block read
    [    8.523043] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.523651] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.524259] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.524863] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.525465] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.526064] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.526664] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.527260] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.527831] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.527885] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.527888] mmcblk0boot0: retrying using single block read
    [    8.528564] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.529174] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.529779] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.530380] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.530979] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.531577] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.532175] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.532771] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.533342] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.533396] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.533399] mmcblk0boot0: retrying using single block read
    [    8.534074] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.534682] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.535283] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.535884] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.536485] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.537086] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.537681] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.538284] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.538854] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.538903] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.538906] mmcblk0boot0: retrying using single block read
    [    8.539574] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.540181] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.540786] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.541394] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.541993] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.542597] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.543197] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.543794] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.544365] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.544418] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.544421] mmcblk0boot0: retrying using single block read
    [    8.545098] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.545704] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.546309] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.546916] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.547529] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.548119] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.548715] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.549309] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.549883] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.549943] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.549947] mmcblk0boot0: retrying using single block read
    [    8.550622] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.551229] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.551833] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.552433] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.553057] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.553628] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.554225] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.554819] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.555396] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.555450] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.555453] mmcblk0boot0: retrying using single block read
    [    8.556127] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.556731] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.557349] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.557936] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.558534] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.559138] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.559735] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.560335] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.560910] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.560963] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.560966] mmcblk0boot0: retrying using single block read
    [    8.561643] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.562247] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.562853] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.563454] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.564060] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.564664] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.565258] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.565857] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.566427] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.566482] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.566484] mmcblk0boot0: retrying using single block read
    [    8.567157] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.567768] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.568368] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.568971] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.569571] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.570174] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.570768] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.571365] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.571937] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.571990] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.571993] mmcblk0boot0: retrying using single block read
    [    8.572664] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.573275] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.573877] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.574477] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.575081] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.575679] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.576274] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.576875] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.577437] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.577489] mmcblk0boot0: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0xb00
    [    8.577493] mmcblk0boot0: retrying using single block read
    [    8.578157] mmcblk0boot0: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0x0
    [    8.578753] mmcblk0boot0: error -84 transferring data, sector 25, nr 7, cmd response 0x900, card status 0x0
    [    8.579345] mmcblk0boot0: error -84 transferring data, sector 26, nr 6, cmd response 0x900, card status 0x0
    [    8.579940] mmcblk0boot0: error -84 transferring data, sector 27, nr 5, cmd response 0x900, card status 0x0
    [    8.580531] mmcblk0boot0: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    [    8.581120] mmcblk0boot0: error -84 transferring data, sector 29, nr 3, cmd response 0x900, card status 0x0
    [    8.581708] mmcblk0boot0: error -84 transferring data, sector 30, nr 2, cmd response 0x900, card status 0x0
    [    8.582296] mmcblk0boot0: error -84 transferring data, sector 31, nr 1, cmd response 0x900, card status 0x0
    [    8.583458] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.583510] mmcblk0boot1: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    8.583513] mmcblk0boot1: retrying using single block read
    [    8.584179] mmcblk0boot1: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    [    8.584772] mmcblk0boot1: error -84 transferring data, sector 9, nr 7, cmd response 0x900, card status 0x0
    [    8.585361] mmcblk0boot1: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    [    8.585951] mmcblk0boot1: error -84 transferring data, sector 11, nr 5, cmd response 0x900, card status 0x0
    [    8.586538] mmcblk0boot1: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    [    8.587128] mmcblk0boot1: error -84 transferring data, sector 13, nr 3, cmd response 0x900, card status 0x0
    [    8.587717] mmcblk0boot1: error -84 transferring data, sector 14, nr 2, cmd response 0x900, card status 0x0
    [    8.588301] mmcblk0boot1: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    [    8.588873] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.588927] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.588931] mmcblk0boot1: retrying using single block read
    [    8.589605] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.590214] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.590821] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.591422] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.592021] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.592622] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.593218] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.593819] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.594390] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.594443] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.594446] mmcblk0boot1: retrying using single block read
    [    8.595119] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.595724] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.596330] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.596932] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.597533] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.598134] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.598729] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.599331] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.599905] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.599958] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.599961] mmcblk0boot1: retrying using single block read
    [    8.600635] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.601241] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.601842] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.602445] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.603049] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.603648] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.604248] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.604847] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.605420] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.605473] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.605477] mmcblk0boot1: retrying using single block read
    [    8.606149] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.606761] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.607390] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.607980] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.608576] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.609174] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.609772] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.610369] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.610936] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.610997] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.611000] mmcblk0boot1: retrying using single block read
    [    8.611682] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.612286] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.612889] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.613490] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.614089] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.614689] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.615286] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.615882] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.616451] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.616511] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.616515] mmcblk0boot1: retrying using single block read
    [    8.617196] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.617805] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.618402] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.619003] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.619604] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.620202] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.620802] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.621399] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.621969] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.622028] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.622031] mmcblk0boot1: retrying using single block read
    [    8.622709] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.623318] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.623920] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.624527] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.625126] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.625731] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.626332] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.626927] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.627499] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.627560] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.627563] mmcblk0boot1: retrying using single block read
    [    8.628245] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.628852] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.629457] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.630063] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.630663] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.631260] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.631858] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.632454] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.633026] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.633086] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.633089] mmcblk0boot1: retrying using single block read
    [    8.633768] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.634375] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.634978] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.635578] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.636179] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.636777] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.637378] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.637964] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.638539] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.638593] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.638596] mmcblk0boot1: retrying using single block read
    [    8.639267] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.639873] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.640480] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.641081] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.641680] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.642284] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.642878] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.643478] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.644657] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.644710] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.644714] mmcblk0boot0: retrying using single block read
    [    8.645389] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.645995] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.646599] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.647205] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.647810] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.648407] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.649004] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.649598] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.650172] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.650226] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.650229] mmcblk0boot0: retrying using single block read
    [    8.650903] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.651511] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.652113] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.652715] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.653316] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.653913] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.654508] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.655109] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.655678] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.655730] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.655733] mmcblk0boot0: retrying using single block read
    [    8.656404] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.657012] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.657615] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.658217] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.658815] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.659414] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.660018] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.660613] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.661190] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.661244] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.661247] mmcblk0boot0: retrying using single block read
    [    8.661920] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.662530] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.663132] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.663737] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.664337] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.664941] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.665540] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.666137] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.666708] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.666760] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.666763] mmcblk0boot0: retrying using single block read
    [    8.667455] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.668050] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.668657] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.669259] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.669861] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.670458] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.671059] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.671655] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.681707] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.681759] mmcblk0boot1: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0xb00
    [    8.681763] mmcblk0boot1: retrying using single block read
    [    8.682429] mmcblk0boot1: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0x0
    [    8.683022] mmcblk0boot1: error -84 transferring data, sector 25, nr 7, cmd response 0x900, card status 0x0
    [    8.683619] mmcblk0boot1: error -84 transferring data, sector 26, nr 6, cmd response 0x900, card status 0x0
    [    8.684213] mmcblk0boot1: error -84 transferring data, sector 27, nr 5, cmd response 0x900, card status 0x0
    [    8.684802] mmcblk0boot1: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    [    8.685391] mmcblk0boot1: error -84 transferring data, sector 29, nr 3, cmd response 0x900, card status 0x0
    [    8.685980] mmcblk0boot1: error -84 transferring data, sector 30, nr 2, cmd response 0x900, card status 0x0
    [    8.686566] mmcblk0boot1: error -84 transferring data, sector 31, nr 1, cmd response 0x900, card status 0x0
    [    8.687140] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.687194] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.687197] mmcblk0boot1: retrying using single block read
    [    8.687876] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.688477] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.689079] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.689682] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.690282] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.690882] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.691480] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.692079] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.692653] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.692707] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.692710] mmcblk0boot1: retrying using single block read
    [    8.693381] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.693987] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.694592] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.695199] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.695798] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.696403] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.696998] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.697600] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.698171] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.698225] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.698228] mmcblk0boot1: retrying using single block read
    [    8.698899] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.699512] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.700117] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.700719] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.701318] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.701917] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.702514] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.703112] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.703683] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.703736] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.703739] mmcblk0boot1: retrying using single block read
    [    8.704411] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.705016] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.705620] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.706222] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.706820] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.708853] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.709261] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.709857] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.710432] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.710485] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.710488] mmcblk0boot1: retrying using single block read
    [    8.711160] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.711765] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.712367] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.712974] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.713572] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.714178] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.714772] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.715373] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [   17.497366] ata1: softreset failed (1st FIS failed)
    udevd[404]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    udevd[413]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    
    udevd[417]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    udevd[444]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    [   27.507359] ata1: softreset failed (1st FIS failed)
    [   27.857363] ata1: SATA link down (SStatus 0 SControl 300)
    [   27.896671] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
    Starting Bootlog daemon: bootlogd.
    ALSA: Restoring mixer settings...
    No state is present for card DRA7xxEVMMCASP1
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP1
    No state is present for card DRA7xxEVMMCASP2
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP2
    No state is present for card DRA7xxEVMMCASP3
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP3
    No state is present for card DRA7xxEVMMCASP4
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP4
    No state is present for card DRA7xxEVMMCASP8
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP8
    Thu Sep  3 18:41:00 UTC 2015
    
    
    
    2017.11.23 15:00
    
    
    
    This version is for J6
    
    
    
    ****** This application only support ASCII code 0 to 127 ******
    
    
    
    ****** This application only support CB version #F ******
    [   43.416085] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   43.422627] usb usb4: USB disconnect, device number 1
    [   43.430892] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
    [   43.436608] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   43.441755] usb usb3: USB disconnect, device number 1
    [   43.449122] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
    [   43.455756] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   43.460880] usb usb2: USB disconnect, device number 1
    [   43.468127] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
    [   43.473839] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   43.479011] usb usb1: USB disconnect, device number 1
    [   43.486322] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
    [   43.597557] usbcore: deregistering device driver usb
    [   43.604204] usbcore: deregistering interface driver usbfs
    [   43.611324] usbcore: deregistering interface driver hub
    [AB_server.c, make_sure_usb_kernel_stack_removed, 374] temp: drwxr-xr-x   27 root     root             0 Jan  1  1970 .
    dr-xr-xr-x   12 root     root             0 Jan  1  1970 ..
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ac97
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clockevents
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clocksource
    drwxr-xr-x    4 root     root             0 Jan  1  1970 container
    drwxr-xr-x    4 root     root             0 Jan  1  1970 cpu
    drwxr-xr-x    4 root     root             0 Jan  1  1970 edac
    drwxr-xr-x    4 root     root             0 Jan  1  1970 event_source
    drwxr-xr-x    4 root     root             0 Jan  1  1970 hid
    drwxr-xr-x    4 root     root             0 Jan  1  1970 i2c
    drwxr-xr-x    4 root     root             0 Jan  1  1970 iio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mdio_bus
    drwxr-xr-x    4 root     root             0 Jan  1  1970 media
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mipi-dsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mmc
    drwxr-xr-x    5 root     root             0 Jan  1  1970 pci
    drwxr-xr-x    4 root     root             0 Jan  1  1970 platform
    drwxr-xr-x    4 root     root             0 Jan  1  1970 rpmsg
    drwxr-xr-x    4 root     root             0 Jan  1  1970 scsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 sdio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 serio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 soc
    drwxr-xr-x    4 root     root             0 Jan  1  1970 spi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ulpi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 virtio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 workqueue
    
    [AB_server.c, AB_boot_finish, 181] AB boot success, pull high GPIO
    [AB_server.c, AB_boot_finish, 187] AB boot success, pull high GPIO finished
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    /usr/local/bin/set_unused_gpio_input: line 14: echo: write error: Device or resource busy
    /usr/local/bin/set_unused_gpio_input: line 15: /sys/class/gpio/gpio161/direction: No such file or directory
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    INIT: Entering runlevel: 5
    Configuring network interfaces... [   45.373449] net eth0: initializing cpsw version 1.15 (0)
    [   45.379130] net eth0: initialized cpsw ale version 1.4
    [   45.384293] net eth0: ALE Table size 1024
    [   45.391355] libphy: PHY 48485000.mdio:02 not found
    [   45.396173] net eth0: phy "48485000.mdio:02" not found on slave 0, err -19
    [   45.410785] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    /bin/sh: udhcpc: command not found
    done.
    Starting system message bus: dbus.
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (4) Bytes
    
    
    _version[0]: 30
    _version[1]: 31
    _version[2]: 31
    _version[3]: 30
    _version[4]: 0
    _version[5]: 0
    _version[6]: 0
    _version[7]: 0
    _version[8]: 0
    _version[9]: 0
    _version[10]: 0
    _version[11]: 0
    _version[12]: 0
    _version[13]: 0
    _version[14]: 0
    _version[15]: 0
    [AB_server.c, main, 517] AB_server: get CB's HW version 0110
    
    
    [AB_server.c, get_CB_hardware_version_finish, 254] AB get CB hw version finish, gpio pull low
    [AB_server.c, send_AB_model_info_to_CB, 279] write AB model info total (6) Bytes, model: (DRA74X
    )
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    UIM SYSFS Node Not Found
    Starting telnet daemon.
    Starting tiipclad daemon
    GateMP support enabled on host
    
    Opened log file: lad.txt
    
    numProcessors = 5 id = 0 baseId = 0
    
    Spawned daemon: /usr/bin/lad_dra7xx
    
    .
    Starting rpcbind daemon...[AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 1
     ______
    [AB_server.c, sync_CB_status, 312] ______ AB GPIO 109 1, can go ______
    done.
    creating NFS state directory: done
    starting statd: done
    NFS daemon support not enabled in kernel
    Starting syslogd/klogd: done
    Starting thttpd.
    Enabling thermal zones...
    Stopping Bootlog daemon: bootlogd.
    
    root@wnc-j6:~# [AB_server.c, main, 550] ulpi on/off : J6, ULPI test on
    cat /sys/kernel/debug/mmc0/ios
    clock:          52000000 Hz
    vdd:            21 (3.3 ~ 3.4 V)
    bus mode:       2 (push-pull)
    chip select:    0 (don't care)
    power mode:     2 (on)
    bus width:      2 (4 bits)
    timing spec:    1 (mmc high-speed)
    signal voltage: 0 (3.30 V)
    driver type:    0 (driver type B)
    root@wnc-j6:~# lsblk
    NAME         MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
    mmcblk0boot0 179:16   0  128K  1 disk
    mmcblk0boot1 179:32   0  128K  1 disk
    mmcblk1boot0 179:64   0  128K  1 disk
    mmcblk1boot1 179:80   0  128K  1 disk
    mmcblk0      179:0    0  7.3G  0 disk
    mmcblk1      179:48   0  7.3G  0 disk
    |-mmcblk1p1  179:49   0   64M  0 part
    `-mmcblk1p2  179:50   0  7.2G  0 part /
    mmcblk2      179:96   0  3.7G  0 disk
    |-mmcblk2p1  179:97   0   62M  0 part
    `-mmcblk2p2  179:98   0  3.6G  0 part
    root@wnc-j6:~#

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    尊敬的 Kevin:

    基于你上一篇文章,我觉得有点困惑。

    如果可能、请描述有关这些日志的更多详细信息。

    例如、  

    * DRA746 eMMC1接口引导带 eMMC 闪存,包括 TS3A27518、VDD 3.3V、IO 3.3V ? 请确认?  请以下方登录?

    U-Boot SPL 2016.05 (Nov 24 2017 - 15:38:03)
    DRA752-GP ES2.0
    *** Warning - bad CRC, using default environment
    
    Trying to boot from MMC2_2
    spl: falcon_args_file not set in environment, falling back to default
    reading args
    spl_load_image_fat_os: error reading image args, err - -1
    reading u-boot.img
    reading u-boot.img
    
    
    U-Boot 2016.05 (Nov 24 2017 - 15:38:03 +0800)
    
    CPU  : DRA752-GP ES2.0
    Board: DRA74x EVM REV
    I2C:   ready
    DRAM:  2 GiB
    MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
    *** Warning - bad CRC, using default environment
    
    Warning: fastboot.board_rev: unknown board revision
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid GPT ***
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid Backup GPT ***
    ERROR: cannot find partition: 'userdata'
    
    at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size()
    Warning: fastboot.userdata_size: unable to calc
    Net:   <ethaddr> not set. Validating first E-fuse MAC
    Could not get PHY for cpsw: addr 2
    cpsw
    Hit any key to stop autoboot:  0
    J6 ...
    switch to partitions #0, OK
    mmc1(part 0) is current device
    SD/MMC found on device 1
    4403712 bytes read in 220 ms (19.1 MiB/s)
    113603 bytes read in 13 ms (8.3 MiB/s)
    Booting from mmc1 ...
    Kernel image @ 0x82000000 [ 0x000000 - 0x433200 ]
    ## Flattened Device Tree blob at 88000000
       Booting using the fdt blob at 0x88000000
       Loading Device Tree to 8ffe1000, end 8ffffbc2 ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Linux version 4.19.73-g31275c05a1 (oe-user@oe-host) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #1 SMP PREEMPT Wed Dec 11 12:53:11 UTC 2019
    [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
    [    0.000000] CPU: div instructions available: patching division code
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [    0.000000] OF: fdt: Machine model: TI DRA742 Bowei 20170929 17:30
    [    0.000000] Memory policy: Data cache writealloc
    [    0.000000] efi: Getting EFI parameters from FDT:
    [    0.000000] efi: UEFI not found.
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
    [    0.000000] OF: reserved mem: initialized node ipu2_cma@95800000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
    [    0.000000] OF: reserved mem: initialized node dsp1_cma@99000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
    [    0.000000] OF: reserved mem: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x000000009f000000, size 8 MiB
    [    0.000000] OF: reserved mem: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool
    [    0.000000] cma: Reserved 24 MiB at 0x00000000fd400000
    [    0.000000] OMAP4: Map 0x00000000fed00000 to (ptrval) for dram barrier
    [    0.000000] DRA752 ES2.0
    [    0.000000] random: get_random_bytes called from start_kernel+0xb4/0x470 with crng_init=0
    [    0.000000] percpu: Embedded 16 pages/cpu s36492 r8192 d20852 u65536
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516416
    [    0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=bddb4f41-02 rw rootfstype=ext4 rootwait consoleblank=0 omapdrm.num_crtc=2 drm.debug=0xff
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Memory: 1847196K/2072576K available (10240K kernel code, 341K rwdata, 2800K rodata, 2048K init, 269K bss, 36964K reserved, 188416K cma-reserved, 1265664K highmem)
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    [    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (12256 kB)
    [    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   (2048 kB)
    [    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 342 kB)
    [    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   ( 270 kB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] rcu: Preemptible hierarchical RCU implementation.
    [    0.000000]  Tasks RCU enabled.
    [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
    [    0.000000] ti_dt_clocks_register: missing clkctrl nodes, please update your dts.
    [    0.000000] OMAP clockevent source: timer1 at 31475 Hz
    [    0.000000] arch_timer: cp15 timer(s) running at 5.90MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns
    [    0.000005] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns
    [    0.000018] Switching to timer-based delay loop, resolution 169ns
    [    0.000352] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
    [    0.000362] OMAP clocksource: 32k_counter at 32768 Hz
    [    0.000825] Console: colour dummy device 80x30
    [    0.000844] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
    [    0.000852] This ensures that you still see kernel messages. Please
    [    0.000860] update your kernel commandline.
    [    0.000893] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016)
    [    0.000910] pid_max: default: 32768 minimum: 301
    [    0.001037] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001053] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001614] CPU: Testing write buffer coherency: ok
    [    0.001652] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
    [    0.001863] /cpus/cpu@0 missing clock-frequency property
    [    0.001883] /cpus/cpu@1 missing clock-frequency property
    [    0.001895] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [    0.059892] Setting up static identity map for 0x80200000 - 0x80200060
    [    0.079902] rcu: Hierarchical SRCU implementation.
    [    0.100098] EFI services will not be available.
    [    0.119963] smp: Bringing up secondary CPUs ...
    [    0.200303] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [    0.200309] CPU1: Spectre v2: using ICIALLU workaround
    [    0.200429] smp: Brought up 1 node, 2 CPUs
    [    0.200442] SMP: Total of 2 processors activated (23.60 BogoMIPS).
    [    0.200451] CPU: All CPU(s) started in SVC mode.
    [    0.200917] devtmpfs: initialized
    [    0.221580] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
    [    0.221840] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.221858] futex hash table entries: 512 (order: 3, 32768 bytes)
    [    0.224710] pinctrl core: initialized pinctrl subsystem
    [    0.225222] DMI not present or invalid.
    [    0.225501] NET: Registered protocol family 16
    [    0.226666] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.227660] omap_hwmod: l3_main_2 using broken dt data from ocp
    [    0.249323] omap_hwmod: dma_system: no dt node
    [    0.249333] ------------[ cut here ]------------
    [    0.249356] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.249365] omap_hwmod: dma_system: doesn't have mpu register target base
    [    0.249373] Modules linked in:
    [    0.249391] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.73-g31275c05a1 #1
    [    0.249401] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.249409] Backtrace:
    [    0.249431] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.249443]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.249459] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.249474] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.249485]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.249497] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.249509]  r9:c104b824 r8:00000000 r7:c121252c r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.249524] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.249534]  r3:c0dd0a04 r2:c0dd0560
    [    0.249543]  r5:00000000 r4:c12124f4
    [    0.249558] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.249570]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.249579]  r4:c12124f4
    [    0.249594] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.249604]  r5:c1204c48 r4:c1255740
    [    0.249619] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.249630]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.249647] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.249658]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.249666]  r4:00000000
    [    0.249679] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.249688] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.249698] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.249709] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.249719] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.249728]  r5:c0a0ccd8 r4:00000000
    [    0.249740] ---[ end trace 53f2d3aef28cd7ec ]---
    [    0.266863] omap_hwmod: hdq1w: no dt node
    [    0.266873] ------------[ cut here ]------------
    [    0.266889] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.266898] omap_hwmod: hdq1w: doesn't have mpu register target base
    [    0.266905] Modules linked in:
    [    0.266922] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         4.19.73-g31275c05a1 #1
    [    0.266931] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.266939] Backtrace:
    [    0.266957] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.266969]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.266983] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.266996] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.267007]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.267019] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.267031]  r9:c104b824 r8:00000000 r7:c12117c0 r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.267045] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.267054]  r3:c0dd26fc r2:c0dd0560
    [    0.267064]  r5:00000000 r4:c1211788
    [    0.267078] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.267090]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.267098]  r4:c1211788
    [    0.267113] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.267123]  r5:c1204c48 r4:c1255740
    [    0.267138] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.267150]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.267166] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.267178]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.267186]  r4:00000000
    [    0.267199] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.267208] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.267217] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.267227] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.267237] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.267246]  r5:c0a0ccd8 r4:00000000
    [    0.267255] ---[ end trace 53f2d3aef28cd7ed ]---
    [    0.298674] omap_hwmod: smartreflex_core: no dt node
    [    0.298684] ------------[ cut here ]------------
    [    0.298699] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.298708] omap_hwmod: smartreflex_core: doesn't have mpu register target base
    [    0.298716] Modules linked in:
    [    0.298731] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         4.19.73-g31275c05a1 #1
    [    0.298740] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.298747] Backtrace:
    [    0.298765] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.298777]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.298791] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.298804] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.298815]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.298828] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.298839]  r9:c104b824 r8:00000000 r7:c120fcc8 r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.298854] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.298863]  r3:c0dd2248 r2:c0dd0560
    [    0.298872]  r5:00000000 r4:c120fc90
    [    0.298886] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.298898]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.298907]  r4:c120fc90
    [    0.298920] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.298929]  r5:c1204c48 r4:c1255740
    [    0.298944] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.298955]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.298971] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.298981]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.298989]  r4:00000000
    [    0.299002] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.299011] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.299021] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.299032] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.299042] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.299051]  r5:c0a0ccd8 r4:00000000
    [    0.299060] ---[ end trace 53f2d3aef28cd7ee ]---
    [    0.300114] omap_hwmod: smartreflex_mpu: no dt node
    [    0.300123] ------------[ cut here ]------------
    [    0.300137] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2409 _init.constprop.22+0x1b0/0x4dc
    [    0.300145] omap_hwmod: smartreflex_mpu: doesn't have mpu register target base
    [    0.300152] Modules linked in:
    [    0.300168] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         4.19.73-g31275c05a1 #1
    [    0.300176] Hardware name: Generic DRA74X (Flattened Device Tree)
    [    0.300184] Backtrace:
    [    0.300200] [<c020cad4>] (dump_backtrace) from [<c020ce0c>] (show_stack+0x18/0x1c)
    [    0.300212]  r7:c0dcff84 r6:60000013 r5:00000000 r4:c1251ff0
    [    0.300225] [<c020cdf4>] (show_stack) from [<c09f8a60>] (dump_stack+0x90/0xa4)
    [    0.300238] [<c09f89d0>] (dump_stack) from [<c022e1b8>] (__warn+0xdc/0xf8)
    [    0.300248]  r7:c0dcff84 r6:00000009 r5:00000000 r4:ee87bddc
    [    0.300260] [<c022e0dc>] (__warn) from [<c022ddfc>] (warn_slowpath_fmt+0x50/0x6c)
    [    0.300272]  r9:c104b824 r8:00000000 r7:c120fc54 r6:00000000 r5:c0dd0560 r4:c1204c48
    [    0.300285] [<c022ddb0>] (warn_slowpath_fmt) from [<c100cf2c>] (_init.constprop.22+0x1b0/0x4dc)
    [    0.300295]  r3:c0dd2238 r2:c0dd0560
    [    0.300303]  r5:00000000 r4:c120fc1c
    [    0.300318] [<c100cd7c>] (_init.constprop.22) from [<c100d388>] (__omap_hwmod_setup_all+0x48/0x134)
    [    0.300330]  r10:c10606f4 r9:c104b824 r8:00000000 r7:c100d340 r6:ffffe000 r5:c120a228
    [    0.300338]  r4:c120fc1c
    [    0.300352] [<c100d340>] (__omap_hwmod_setup_all) from [<c020265c>] (do_one_initcall+0x84/0x1b0)
    [    0.300361]  r5:c1204c48 r4:c1255740
    [    0.300376] [<c02025d8>] (do_one_initcall) from [<c1000fe8>] (kernel_init_freeable+0x1c4/0x258)
    [    0.300386]  r8:c104b844 r7:c10004f0 r6:c1255740 r5:c1255740 r4:00000003
    [    0.300401] [<c1000e24>] (kernel_init_freeable) from [<c0a0cce8>] (kernel_init+0x10/0x11c)
    [    0.300412]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a0ccd8
    [    0.300420]  r4:00000000
    [    0.300432] [<c0a0ccd8>] (kernel_init) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
    [    0.300441] Exception stack(0xee87bfb0 to 0xee87bff8)
    [    0.300451] bfa0:                                     00000000 00000000 00000000 00000000
    [    0.300461] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [    0.300471] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    [    0.300480]  r5:c0a0ccd8 r4:00000000
    [    0.300503] ---[ end trace 53f2d3aef28cd7ef ]---
    [    0.413727] cpuidle: using governor ladder
    [    0.413762] cpuidle: using governor menu
    [    0.420395] OMAP GPIO hardware version 0.1
    [    0.423350] GPIO line 161 (radio_rst) hogged as output/low
    [    0.449103] No ATAGs?
    [    0.449182] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [    0.449198] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.449234] omap_device: omap_dma_system: build failed (-22)
    [    0.449245] omap2_system_dma_init_dev: Can't build omap_device for omap_dma_system:dma_system.
    [    0.449617] omap4_sram_init:Unable to allocate sram needed to handle errata I688
    [    0.449628] omap4_sram_init:Unable to get sram pool needed to handle errata I688
    [    0.461236] edma 43300000.edma: memcpy is disabled
    [    0.464490] edma 43300000.edma: TI EDMA DMA engine driver
    [    0.468860] omap-iommu 40d01000.mmu: 40d01000.mmu registered
    [    0.469038] omap-iommu 40d02000.mmu: 40d02000.mmu registered
    [    0.469268] omap-iommu 58882000.mmu: 58882000.mmu registered
    [    0.469500] omap-iommu 55082000.mmu: 55082000.mmu registered
    [    0.469891] omap-iommu 41501000.mmu: 41501000.mmu registered
    [    0.470063] omap-iommu 41502000.mmu: 41502000.mmu registered
    [    0.470321] iommu: Adding device 58820000.ipu to group 1
    [    0.470395] iommu: Adding device 55020000.ipu to group 2
    [    0.470518] iommu: Adding device 40800000.dsp to group 0
    [    0.470755] iommu: Adding device 41000000.dsp to group 3
    [    0.472051] SCSI subsystem initialized
    [    0.473214] palmas 0-0058: IRQ missing: skipping irq request
    [    0.502012] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0
    [    0.503460] SMPS12: supplied by regulator-dummy
    [    0.504494] SMPS3: supplied by regulator-dummy
    [    0.505977] SMPS45: supplied by regulator-dummy
    [    0.507899] SMPS6: supplied by regulator-dummy
    [    0.509678] SMPS7: supplied by regulator-dummy
    [    0.511619] SMPS8: supplied by regulator-dummy
    [    0.513416] SMPS9: supplied by regulator-dummy
    [    0.514430] LDO1: supplied by regulator-dummy
    [    0.522497] LDO2: supplied by regulator-dummy
    [    0.532355] LDO3: supplied by regulator-dummy
    [    0.542366] LDO4: supplied by regulator-dummy
    [    0.542480] random: fast init done
    [    0.543106] LDO5: supplied by regulator-dummy
    [    0.543822] LDO6: supplied by regulator-dummy
    [    0.544536] LDO7: supplied by regulator-dummy
    [    0.545258] LDO8: supplied by regulator-dummy
    [    0.545983] LDO9: supplied by regulator-dummy
    [    0.552407] LDOLN: supplied by regulator-dummy
    [    0.562428] LDOUSB: supplied by regulator-dummy
    [    0.574354] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
    [    0.575034] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
    [    0.575434] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
    [    0.575819] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
    [    0.576208] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
    [    0.576442] media: Linux media interface: v0.10
    [    0.576481] videodev: Linux video capture interface: v2.00
    [    0.576554] pps_core: LinuxPPS API ver. 1 registered
    [    0.576564] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.576585] PTP clock support registered
    [    0.576615] EDAC MC: Ver: 3.0.0
    [    0.577357] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
    [    0.577608] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
    [    0.578128] Advanced Linux Sound Architecture Driver Initialized.
    [    0.578905] clocksource: Switched to clocksource arch_sys_counter
    [    0.586764] NET: Registered protocol family 2
    [    0.587353] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
    [    0.587382] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.587446] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.587573] TCP: Hash tables configured (established 8192 bind 8192)
    [    0.587646] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [    0.587680] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [    0.587809] NET: Registered protocol family 1
    [    0.608247] RPC: Registered named UNIX socket transport module.
    [    0.608257] RPC: Registered udp transport module.
    [    0.608266] RPC: Registered tcp transport module.
    [    0.608275] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.609320] hw perfevents: no interrupt-affinity property for /pmu, guessing.
    [    0.609542] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
    [    0.610512] Initialise system trusted keyrings
    [    0.610637] workingset: timestamp_bits=14 max_order=19 bucket_order=5
    [    0.615512] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.626001] NFS: Registering the id_resolver key type
    [    0.626021] Key type id_resolver registered
    [    0.626030] Key type id_legacy registered
    [    0.626072] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.627627] Key type asymmetric registered
    [    0.627639] Asymmetric key parser 'x509' registered
    [    0.627686] bounce: pool size: 64 pages
    [    0.627721] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
    [    0.627732] io scheduler noop registered
    [    0.627741] io scheduler deadline registered
    [    0.627838] io scheduler cfq registered (default)
    [    0.627849] io scheduler mq-deadline registered
    [    0.627859] io scheduler kyber registered
    [    0.632793] pinctrl-single 4a003400.pinmux: please update dts to use #pinctrl-cells = <1>
    [    0.633318] pinctrl-single 4a003400.pinmux: 282 pins, size 1128
    [    0.640553] pbias_mmc_omap5: Bringing 3300000uV into 3000000-3000000uV
    [    0.640569] pbias_mmc_omap5: failed to apply 3000000-3000000uV constraint(-22)
    [    0.640584] pbias-regulator 4a002e00.pbias_regulator: Failed to register regulator: -22
    [    0.640607] pbias-regulator: probe of 4a002e00.pbias_regulator failed with error -22
    [    0.641433] evm_3v3_sw: supplied by sysen1
    [    0.641672] aic_dvdd: supplied by evm_3v3_sw
    [    0.641746] vtt_fixed: supplied by sysen2
    [    0.684673] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled
    [    0.688596] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
    [    0.689534] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 44, base_baud = 3000000) is a 8250
    [    0.690440] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 45, base_baud = 3000000) is a 8250
    [    2.662588] console [ttyS2] enabled
    [    2.667015] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 46, base_baud = 3000000) is a 8250
    [    2.676670] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 47, base_baud = 3000000) is a 8250
    [    2.686320] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 48, base_baud = 3000000) is a 8250
    [    2.695978] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 49, base_baud = 3000000) is a 8250
    [    2.707068] omap_rng 48090000.rng: Random Number Generator ver. 20
    [    2.707405] random: crng init done
    [    2.717505] omapdss_dss 58000000.dss: Linked as a consumer to regulator.22
    [    2.724599] DSS: OMAP DSS rev 6.1
    [    2.729644] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
    [    2.750327] brd: module loaded
    [    2.759517] loop: module loaded
    [    2.768957] libphy: Fixed MDIO Bus: probed
    [    2.828934] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000
    [    2.836627] davinci_mdio 48485000.mdio: no live phy, scanning all
    [    2.939022] davinci_mdio 48485000.mdio: timed out waiting for user access
    [    3.045927] davinci_mdio 48485000.mdio: timed out waiting for idle
    [    3.052180] davinci_mdio: probe of 48485000.mdio failed with error -5
    [    3.059289] cpsw 48484000.ethernet: Detected MACID = 54:45:38:a7:aa:1e
    [    3.065891] cpsw 48484000.ethernet: initialized cpsw ale version 1.4
    [    3.072295] cpsw 48484000.ethernet: ALE Table size 1024
    [    3.077569] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies)
    [    3.085580] cpsw 48484000.ethernet: cpsw: Detected MACID = 54:45:38:a7:aa:1f
    [    3.094209] i2c /dev entries driver
    [    3.102604] cpu cpu0: "syscon" is missing, cannot use OPPv2 table.
    [    3.109347] sdhci: Secure Digital Host Controller Interface driver
    [    3.115555] sdhci: Copyright(c) Pierre Ossman
    [    3.120930] omap_hsmmc: probe of 4809c000.mmc failed with error -22
    [    3.127666] omap_hsmmc 480b4000.mmc: RX DMA channel request failed
    [    3.134325] omap_hsmmc 480d1000.mmc: RX DMA channel request failed
    [    3.140842] sdhci-pltfm: SDHCI platform and OF driver helper
    [    3.147883] ledtrig-cpu: registered to indicate activity on CPUs
    [    3.158457] pinctrl-single 4a003400.pinmux: pin PIN170 already requested by 4806a000.serial; cannot claim for 48460000.mcasp
    [    3.169766] pinctrl-single 4a003400.pinmux: pin-170 (48460000.mcasp) status -22
    [    3.177113] pinctrl-single 4a003400.pinmux: could not request pin 170 (PIN170) from group mcasp1_pins  on device pinctrl-single
    [    3.188662] davinci-mcasp 48460000.mcasp: Error applying setting, reverse things back
    [    3.196555] davinci-mcasp: probe of 48460000.mcasp failed with error -22
    [    3.203365] pinctrl-single 4a003400.pinmux: pin PIN192 already requested by 4806a000.serial; cannot claim for 48464000.mcasp
    [    3.214653] pinctrl-single 4a003400.pinmux: pin-192 (48464000.mcasp) status -22
    [    3.222021] pinctrl-single 4a003400.pinmux: could not request pin 192 (PIN192) from group mcasp2_pins  on device pinctrl-single
    [    3.233565] davinci-mcasp 48464000.mcasp: Error applying setting, reverse things back
    [    3.241452] davinci-mcasp: probe of 48464000.mcasp failed with error -22
    [    3.248237] pinctrl-single 4a003400.pinmux: pin PIN203 already requested by 4806a000.serial; cannot claim for 48468000.mcasp
    [    3.259523] pinctrl-single 4a003400.pinmux: pin-203 (48468000.mcasp) status -22
    [    3.266867] pinctrl-single 4a003400.pinmux: could not request pin 203 (PIN203) from group mcasp3_pins  on device pinctrl-single
    [    3.278408] davinci-mcasp 48468000.mcasp: Error applying setting, reverse things back
    [    3.286294] davinci-mcasp: probe of 48468000.mcasp failed with error -22
    [    3.293092] pinctrl-single 4a003400.pinmux: pin PIN205 already requested by 4806a000.serial; cannot claim for 4846c000.mcasp
    [    3.304377] pinctrl-single 4a003400.pinmux: pin-205 (4846c000.mcasp) status -22
    [    3.311736] pinctrl-single 4a003400.pinmux: could not request pin 205 (PIN205) from group mcasp4_pins  on device pinctrl-single
    [    3.323278] davinci-mcasp 4846c000.mcasp: Error applying setting, reverse things back
    [    3.331166] davinci-mcasp: probe of 4846c000.mcasp failed with error -22
    [    3.337955] pinctrl-single 4a003400.pinmux: pin PIN200 already requested by 4806a000.serial; cannot claim for 4847c000.mcasp
    [    3.349246] pinctrl-single 4a003400.pinmux: pin-200 (4847c000.mcasp) status -22
    [    3.356590] pinctrl-single 4a003400.pinmux: could not request pin 200 (PIN200) from group mcasp8_pins  on device pinctrl-single
    [    3.368134] davinci-mcasp 4847c000.mcasp: Error applying setting, reverse things back
    [    3.376023] davinci-mcasp: probe of 4847c000.mcasp failed with error -22
    [    3.383480] NET: Registered protocol family 10
    [    3.388888] Segment Routing with IPv6
    [    3.392659] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
    [    3.399094] NET: Registered protocol family 17
    [    3.403756] Key type dns_resolver registered
    [    3.408154] Registering SWP/SWPB emulation handler
    [    3.412990] omap_voltage_late_init: Voltage driver support not added
    [    3.419391] Power Management for TI OMAP4+ devices.
    [    3.424978] Loading compiled-in X.509 certificates
    [    3.446882] dmm 4e000000.dmm: failed to initialize work-around for i878
    [    3.455039] dmm 4e000000.dmm: initialized all PAT entries
    [    3.461135] omapdrm omapdrm.0: omap_modeset_init failed: ret=-517
    [    3.468175] omapdrm omapdrm.0: omap_modeset_init failed: ret=-517
    [    3.475138] omapdrm omapdrm.0: omap_modeset_init failed: ret=-517
    [    3.481870] hctosys: unable to open rtc device (rtc0)
    [    3.487585] aic_dvdd: disabling
    [    3.490956] ldousb: disabling
    [    3.494251] ALSA device list:
    [    3.497232]   No soundcards found.
    [    3.501323] Waiting for root device PARTUUID=bddb4f41-02...

    * DRA746 eMMC1接口引导带 eMMC 闪存,包括 TS3A27518, VDD 1.8V, IO 1.8V? 请确认?  请以下方登录?

    我想您可以根据此日志案例在此处发布器件树。

    U-Boot SPL 2016.05 (Nov 24 2017 - 15:38:03)
    DRA752-GP ES2.0
    *** Warning - bad CRC, using default environment
    
    Trying to boot from MMC2_2
    spl: falcon_args_file not set in environment, falling back to default
    reading args
    spl_load_image_fat_os: error reading image args, err - -1
    reading u-boot.img
    reading u-boot.img
    
    
    U-Boot 2016.05 (Nov 24 2017 - 15:38:03 +0800)
    
    CPU  : DRA752-GP ES2.0
    Board: DRA74x EVM REV
    I2C:   ready
    DRAM:  2 GiB
    MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
    *** Warning - bad CRC, using default environment
    
    Warning: fastboot.board_rev: unknown board revision
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid GPT ***
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid Backup GPT ***
    ERROR: cannot find partition: 'userdata'
    
    at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size()
    Warning: fastboot.userdata_size: unable to calc
    Net:   <ethaddr> not set. Validating first E-fuse MAC
    Could not get PHY for cpsw: addr 2
    cpsw
    Hit any key to stop autoboot:  0
    J6 ...
    switch to partitions #0, OK
    mmc1(part 0) is current device
    SD/MMC found on device 1
    4281344 bytes read in 213 ms (19.2 MiB/s)
    113071 bytes read in 12 ms (9 MiB/s)
    Booting from mmc1 ...
    Kernel image @ 0x82000000 [ 0x000000 - 0x415400 ]
    ## Flattened Device Tree blob at 88000000
       Booting using the fdt blob at 0x88000000
       Loading Device Tree to 8ffe1000, end 8ffff9ae ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpuset
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Initializing cgroup subsys cpuacct
    [    0.000000] Linux version 4.4.45 (bowei@bowei-Veriton-M490) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #75 SMP PREEMPT Mon Jan 22 10:50:18 CST 2018
    [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [    0.000000] Machine model: TI DRA742 Louis 20170929 17:30
    [    0.000000] Reserved memory: created CMA memory pool at 0x95800000, size 56 MiB
    [    0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x99000000, size 64 MiB
    [    0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9d000000, size 32 MiB
    [    0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9f000000, size 8 MiB
    [    0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool
    [    0.000000] cma: Reserved 24 MiB at 0xfd400000
    [    0.000000] Memory policy: Data cache writealloc
    [    0.000000] OMAP4: Map 0xfee00000 to fe600000 for dram barrier
    [    0.000000] DRA752 ES2.0
    [    0.000000] PERCPU: Embedded 12 pages/cpu @eed51000 s18944 r8192 d22016 u49152
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 516672
    [    0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=bddb4f41-02 rw rootfstype=ext4 rootwait consoleblank=0 omapdrm.num_crtc=2 drm.debug=0xff
    [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Memory: 1851432K/2073600K available (7719K kernel code, 797K rwdata, 4560K rodata, 372K init, 291K bss, 33752K reserved, 188416K cma-reserved, 1266688K highmem)
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    [    0.000000]       .text : 0xc0008000 - 0xc0c0607c   (12281 kB)
    [    0.000000]       .init : 0xc0c07000 - 0xc0c64000   ( 372 kB)
    [    0.000000]       .data : 0xc0c64000 - 0xc0d2b530   ( 798 kB)
    [    0.000000]        .bss : 0xc0d2d000 - 0xc0d75f00   ( 292 kB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] Preemptible hierarchical RCU implementation.
    [    0.000000]  Build-time adjustment of leaf fanout to 32.
    [    0.000000] NR_IRQS:16 nr_irqs:16 16
    [    0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div
    [    0.000000] OMAP clockevent source: timer1 at 31475 Hz
    [    0.000000] Architected cp15 timer(s) running at 5.90MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns
    [    0.000004] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns
    [    0.000015] Switching to timer-based delay loop, resolution 169ns
    [    0.000325] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
    [    0.000333] OMAP clocksource: 32k_counter at 32768 Hz
    [    0.000786] Console: colour dummy device 80x30
    [    0.000803] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
    [    0.000810] This ensures that you still see kernel messages. Please
    [    0.000816] update your kernel commandline.
    [    0.000828] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016)
    [    0.000841] pid_max: default: 32768 minimum: 301
    [    0.000934] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.000944] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001474] Initializing cgroup subsys io
    [    0.001492] Initializing cgroup subsys memory
    [    0.001515] Initializing cgroup subsys devices
    [    0.001528] Initializing cgroup subsys freezer
    [    0.001539] Initializing cgroup subsys perf_event
    [    0.001550] Initializing cgroup subsys pids
    [    0.001576] CPU: Testing write buffer coherency: ok
    [    0.001771] /cpus/cpu@0 missing clock-frequency property
    [    0.001787] /cpus/cpu@1 missing clock-frequency property
    [    0.001797] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [    0.001837] Setting up static identity map for 0x80008340 - 0x800083a0
    [    0.080051] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [    0.080113] Brought up 2 CPUs
    [    0.080126] SMP: Total of 2 processors activated (23.60 BogoMIPS).
    [    0.080133] CPU: All CPU(s) started in SVC mode.
    [    0.081170] devtmpfs: initialized
    [    0.111084] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
    [    0.112068] omap_hwmod: l3_main_2 using broken dt data from ocp
    [    0.310433] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.314133] pinctrl core: initialized pinctrl subsystem
    [    0.314996] NET: Registered protocol family 16
    [    0.315935] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.340217] cpuidle: using governor ladder
    [    0.370240] cpuidle: using governor menu
    [    0.378504] OMAP GPIO hardware version 0.1
    [    0.382624] GPIO line 161 (radio_rst) hogged as output/low
    [    0.414591] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [    0.414601] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.415081] omap4_sram_init:Unable to allocate sram needed to handle errata I688
    [    0.415090] omap4_sram_init:Unable to get sram pool needed to handle errata I688
    [    0.415576] OMAP DMA hardware revision 0.0
    [    0.461550] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
    [    0.462798] edma 43300000.edma: memcpy is disabled
    [    0.467537] edma 43300000.edma: TI EDMA DMA engine driver
    [    0.471761] omap-iommu 40d01000.mmu: 40d01000.mmu registered
    [    0.471943] omap-iommu 40d02000.mmu: 40d02000.mmu registered
    [    0.472102] omap-iommu 58882000.mmu: 58882000.mmu registered
    [    0.472260] omap-iommu 55082000.mmu: 55082000.mmu registered
    [    0.472557] omap-iommu 41501000.mmu: 41501000.mmu registered
    [    0.472749] omap-iommu 41502000.mmu: 41502000.mmu registered
    [    0.474753] SCSI subsystem initialized
    [    0.476005] ======palmas_i2c_probe:526========
    [    0.476022] ======palmas_i2c_probe:559, features=0x0========
    [    0.476333] palmas 0-0058: IRQ missing: skipping irq request
    [    0.491064] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0
    [    0.562796] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
    [    0.563432] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
    [    0.563797] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
    [    0.564169] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
    [    0.564534] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
    [    0.564756] media: Linux media interface: v0.10
    [    0.564806] Linux video capture interface: v2.00
    [    0.564844] pps_core: LinuxPPS API ver. 1 registered
    [    0.564851] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.564874] PTP clock support registered
    [    0.564900] EDAC MC: Ver: 3.0.0
    [    0.565665] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
    [    0.565959] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
    [    0.566304] Advanced Linux Sound Architecture Driver Initialized.
    [    0.567188] clocksource: Switched to clocksource arch_sys_counter
    [    0.577940] NET: Registered protocol family 2
    [    0.578431] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.578494] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.578619] TCP: Hash tables configured (established 8192 bind 8192)
    [    0.578665] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [    0.578698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [    0.578907] NET: Registered protocol family 1
    [    0.579172] RPC: Registered named UNIX socket transport module.
    [    0.579181] RPC: Registered udp transport module.
    [    0.579187] RPC: Registered tcp transport module.
    [    0.579193] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.580238] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
    [    0.582696] futex hash table entries: 512 (order: 3, 32768 bytes)
    [    0.589425] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.590074] NFS: Registering the id_resolver key type
    [    0.590098] Key type id_resolver registered
    [    0.590106] Key type id_legacy registered
    [    0.590171] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.592152] bounce: pool size: 64 pages
    [    0.592306] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
    [    0.592323] io scheduler noop registered
    [    0.592337] io scheduler deadline registered
    [    0.592371] io scheduler cfq registered (default)
    [    0.597689] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
    [    0.658363] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
    [    0.661951] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 299, base_baud = 3000000) is a 8250
    [    0.662826] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 300, base_baud = 3000000) is a 8250
    [    0.663687] console [ttyS2] disabled
    [    0.663732] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250
    [    1.550527] console [ttyS2] enabled
    [    1.554926] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 302, base_baud = 3000000) is a 8250
    [    1.564654] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 303, base_baud = 3000000) is a 8250
    [    1.574335] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 304, base_baud = 3000000) is a 8250
    [    1.584013] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 305, base_baud = 3000000) is a 8250
    [    1.594154] [drm] Initialized drm 1.1.0 20060810
    [    1.600370] OMAP DSS rev 6.1
    [    1.604134] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
    [    1.625872] brd: module loaded
    [    1.634088] loop: module loaded
    [    1.643758] libphy: Fixed MDIO Bus: probed
    [    1.648467] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
    [    1.655547] e1000: Copyright (c) 1999-2006 Intel Corporation.
    [    1.661395] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    [    1.667267] e1000e: Copyright(c) 1999 - 2015     2.019967] tvp5158 1-0058: ERROR: Chip id is not TVP5158
    [    2.025505] ov1063x 1-0037: ov1063x Product ID 0 Manufacturer ID 0
    [    2.031731] ov1063x 1-0037: ov1063x 1-0037 sensor driver registered !!
    [    2.039140] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
    [    2.046236] vip 48990000.vip: loading firmware vpdma-1b8.bin
    [    2.055636] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr104 mode
    [    2.062254] omap_hsmmc 4809c000.mmc: no pinctrl state for ddr50 mode
    [    2.068685] vpe 489d0000.vpe: Device registered as /dev/video0
    [    2.074558] vip 48990000.vip: VPDMA firmware loaded
    [    2.079496] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr50 mode
    [    2.079606] vip2-s1: Port B: Using subdev ov1063x 1-0037 for capture
    [    2.092316] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr25 mode
    [    2.092334] vip2-s1: device registered as video1
    [    2.103347] omap_hsmmc 4809c000.mmc: no pinctrl state for sdr12 mode
    [    2.110958] ldo1: voltage operation not allowed
    [    2.115512] omap_hsmmc 4809c000.mmc: vmmc_aux set voltage failed
    [    2.121567] omap_hsmmc 4809c000.mmc: failed to switch to 3v
    [    2.167614] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
    [    2.173998] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
    [    2.180403] omap_hsmmc 480b4000.mmc: no pinctrl state for hs200_1_8v mode
    [    2.187373] evm_3v3_sw: supplied by sysen1
    [    2.227553] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr25 mode
    [    2.233936] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr12 mode
    [    2.240334] omap_hsmmc 480d1000.mmc: no pinctrl state for hs mode
    [    2.278007] ledtrig-cpu: registered to indicate activity on CPUs
    [    2.286092] hwspinlock_user gatemp: requested 10 hwspinlocks
    [    2.307085] pinctrl-single 4a003400.pinmux: pin 4a0036a8.0 already requested by 4806a000.serial; cannot claim for 48460000.mcasp
    [    2.318722] pinctrl-single 4a003400.pinmux: pin-170 (48460000.mcasp) status -22
    [    2.326065] pinctrl-single 4a003400.pinmux: could not request pin 170 (4a0036a8.0) from group mcasp1_pins  on device pinctrl-single
    [    2.337990] davinci-mcasp 48460000.mcasp: Error applying setting, reverse things back
    [    2.346265] davinci-mcasp 48460000.mcasp: Update the bindings to use assigned-clocks!
    [    2.354169] davinci-mcasp 48460000.mcasp: failed to reparent fck
    [    2.360453] pinctrl-single 4a003400.pinmux: pin 4a003700.0 already requested by 4806a000.serial; cannot claim for 48464000.mcasp
    [    2.372083] pinctrl-single 4a003400.pinmux: pin-192 (48464000.mcasp) status -22
    [    2.379466] pinctrl-single 4a003400.pinmux: could not request pin 192 (4a003700.0) from group mcasp2_pins  on device pinctrl-single
    [    2.391353] davinci-mcasp 48464000.mcasp: Error applying setting, reverse things back
    [    2.399601] davinci-mcasp 48464000.mcasp: Update the bindings to use assigned-clocks!
    [    2.407503] davinci-mcasp 48464000.mcasp: failed to reparent fck
    [    2.413764] pinctrl-single 4a003400.pinmux: pin 4a00372c.0 already requested by 4806a000.serial; cannot claim for 48468000.mcasp
    [    2.425394] pinctrl-single 4a003400.pinmux: pin-203 (48468000.mcasp) status -22
    [    2.432746] pinctrl-single 4a003400.pinmux: could not request pin 203 (4a00372c.0) from group mcasp3_pins  on device pinctrl-single
    [    2.444630] davinci-mcasp 48468000.mcasp: Error applying setting, reverse things back
    [    2.452883] davinci-mcasp 48468000.mcasp: Update the bindings to use assigned-clocks!
    [    2.460781] davinci-mcasp 48468000.mcasp: failed to reparent fck
    [    2.467029] pinctrl-single 4a003400.pinmux: pin 4a003734.0 already requested by 4806a000.serial; cannot claim for 4846c000.mcasp
    [    2.478659] pinctrl-single 4a003400.pinmux: pin-205 (4846c000.mcasp) status -22
    [    2.486000] pinctrl-single 4a003400.pinmux: could not request pin 205 (4a003734.0) from group mcasp4_pins  on device pinctrl-single
    [    2.497884] davinci-mcasp 4846c000.mcasp: Error applying setting, reverse things back
    [    2.506119] davinci-mcasp 4846c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.514017] davinci-mcasp 4846c000.mcasp: failed to reparent fck
    [    2.520274] pinctrl-single 4a003400.pinmux: pin 4a003720.0 already requested by 4806a000.serial; cannot claim for 4847c000.mcasp
    [    2.531903] pinctrl-single 4a003400.pinmux: pin-200 (4847c000.mcasp) status -22
    [    2.539259] pinctrl-single 4a003400.pinmux: could not request pin 200 (4a003720.0) from group mcasp8_pins  on device pinctrl-single
    [    2.551144] davinci-mcasp 4847c000.mcasp: Error applying setting, reverse things back
    [    2.559399] davinci-mcasp 4847c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.567295] davinci-mcasp 4847c000.mcasp: failed to reparent fck
    [    2.574511] NET: Registered protocol family 10
    [    2.589790] sit: IPv6 over IPv4 tunneling driver
    [    2.594962] NET: Registered protocol family 17
    [    2.599689] Key type dns_resolver registered
    [    2.604103] omap_voltage_late_init: Voltage driver support not added
    [    2.611013] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    2.617234] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    2.623486] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    2.630118] Power Management for TI OMAP4+ devices.
    [    2.635259] Registering SWP/SWPB emulation handler
    [    2.642711] dmm 4e000000.dmm: initialized all PAT entries
    [    2.670836] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [    2.677498] [drm] No driver support for vblank timestamp query.
    [    2.694269] [drm] Enabling DMM ywrap scrolling
    [    2.700353] mmc0: MAN_BKOPS_EN bit is not set
    [    2.766111] mmc0: new high speed MMC card at address 0001
    [    2.769704] Console: switching to colour frame buffer device 240x67
    [    2.776758] mmcblk0: mmc0:0001 R1J55A 7.28 GiB
    [    2.787071] mmcblk0boot0: mmc0:0001 R1J55A partition 1 128 KiB
    [    2.787361] mmcblk0boot1: mmc0:0001 R1J55A partition 2 128 KiB
    [    2.789666]  mmcblk0: p1
    [    2.819602] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
    [    2.840325] mmc1: MAN_BKOPS_EN bit is not set
    [    2.848456] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
    [    2.876112] asoc-simple-card-mcasp1 sound@1: bt-sco-pcm-mcasp1 <-> 48460000.mcasp mapping ok
    [    2.885192] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPLOUT
    [    2.895052] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.904698] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPROUT
    [    2.912491] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.922113] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for LLOUT
    [    2.929912] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.938926] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for RLOUT
    [    2.946616] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.955625] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3L
    [    2.963148] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.972157] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3R
    [    2.979688] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.988698] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for Mic Bias
    [    2.996648] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.005920] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1L
    [    3.013570] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.022585] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1R
    [    3.030200] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.041140] asoc-simple-card-mcasp2 sound@2: bt-sco-pcm-mcasp2 <-> 48464000.mcasp mapping ok
    [    3.049640] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPLOUT
    [    3.057436] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.067046] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPROUT
    [    3.074836] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.084456] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for LLOUT
    [    3.092158] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.101190] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for RLOUT
    [    3.108899] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.117910] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3L
    [    3.125425] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.134431] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3R
    [    3.141957] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.150966] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for Mic Bias
    [    3.158928] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.168201] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1L
    [    3.175804] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.184813] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1R
    [    3.192463] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.203248] asoc-simple-card-mcasp3 sound@3: bt-sco-pcm-mcasp3 <-> 48468000.mcasp mapping ok
    [    3.211747] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPLOUT
    [    3.217732] mmc1: new DDR MMC card at address 0001
    [    3.224358] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.228252] mmcblk1: mmc1:0001 R1J55A 7.28 GiB
    [    3.238527] mmcblk1boot0: mmc1:0001 R1J55A partition 1 128 KiB
    [    3.244403] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPROUT
    [    3.248798] mmcblk1boot1: mmc1:0001 R1J55A partition 2 128 KiB
    [    3.253032]  mmcblk1: p1 p2
    [    3.260869] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.270494] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for LLOUT
    [    3.278203] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.287215] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for RLOUT
    [    3.294904] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.303945] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3L
    [    3.311478] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.320489] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3R
    [    3.328017] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.337016] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for Mic Bias
    [    3.344690] mmc2: host does not support reading read-only switch, assuming write-enable
    [    3.344758] mmc2: new SDHC card at address 0001
    [    3.355217] mmcblk2: mmc2:0001 SD4GB 3.64 GiB
    [    3.357067]  mmcblk2: p1 p2
    [    3.364844] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.374128] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1L
    [    3.381745] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.390761] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1R
    [    3.398378] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.409327] asoc-simple-card-mcasp4 sound@4: bt-sco-pcm-mcasp4 <-> 4846c000.mcasp mapping ok
    [    3.417832] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPLOUT
    [    3.425611] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.435232] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPROUT
    [    3.443023] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.452645] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for LLOUT
    [    3.460342] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.469352] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for RLOUT
    [    3.477041] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.486050] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3L
    [    3.493577] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.502613] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3R
    [    3.510142] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.519153] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for Mic Bias
    [    3.527103] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.536374] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1L
    [    3.543984] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.552994] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1R
    [    3.560604] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.571782] asoc-simple-card-mcasp8 sound@8: bt-sco-pcm-mcasp8 <-> 4847c000.mcasp mapping ok
    [    3.580284] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPLOUT
    [    3.588077] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    3.597697] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPROUT
    [    3.605474] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    3.615090] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for LLOUT
    [    3.622793] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    3.631802] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for RLOUT
    [    3.639503] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    3.648514] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3L
    [    3.656027] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    3.665036] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3R
    [    3.672562] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    3.681572] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for Mic Bias
    [    3.689533] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    3.698836] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1L
    [    3.706439] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    3.715447] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1R
    [    3.723063] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    3.732961] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    3.739190] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    3.745445] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    3.752502] hctosys: unable to open rtc device (rtc0)
    [    3.769351] aic_dvdd: disabling
    [    3.772756] ldousb: disabling
    [    3.776239] ALSA device list:
    [    3.779235]   #0: DRA7xx-EVM-MCASP1
    [    3.782737]   #1: DRA7xx-EVM-MCASP2
    [    3.786237]   #2: DRA7xx-EVM-MCASP3
    [    3.789751]   #3: DRA7xx-EVM-MCASP4
    [    3.793250]   #4: DRA7xx-EVM-MCASP8
    [    3.865870] EXT4-fs (mmcblk1p2): recovery complete
    [    3.871133] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
    [    3.879308] VFS: Mounted root (ext4 filesystem) on device 179:50.
    [    3.886821] devtmpfs: mounted
    [    3.890040] Freeing unused kernel memory: 372K (c0c07000 - c0c64000)
    [    3.896420] This architecture does not have kernel memory protection.
    INIT: version 2.88 booting
    Starting udev
    [    4.183148] udevd[129]: starting version 182
    [    4.641595] omap-rproc 58820000.ipu: assigned reserved memory node ipu1_cma@9d000000
    [    4.720397]  remoteproc0: 58820000.ipu is available
    [    4.872043]  remoteproc0: Note: remoteproc is still under development and considered experimental.
    [    4.987275]  remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.014205] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.014593]  remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2
    [    5.014601]  remoteproc0: failed to load dra7-ipu1-fw.xem4
    [    5.015604] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@95800000
    [    5.015663]  remoteproc1: 55020000.ipu is available
    [    5.015667]  remoteproc1: Note: remoteproc is still under development and considered experimental.
    [    5.015670]  remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.017603] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@99000000
    [    5.017660]  remoteproc2: 40800000.dsp is available
    [    5.017664]  remoteproc2: Note: remoteproc is still under development and considered experimental.
    [    5.017667]  remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.018494] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9f000000
    [    5.018545]  remoteproc3: 41000000.dsp is available
    [    5.018549]  remoteproc3: Note: remoteproc is still under development and considered experimental.
    [    5.018551]  remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.027750] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20
    [    5.029286] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
    [    5.045557]  remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2
    [    5.045566]  remoteproc3: failed to load dra7-dsp2-fw.xe66
    [    5.046387]  remoteproc2: registered virtio0 (type 7)
    [    5.060817] alg: skcipher: setkey failed on test 5 for ecb-des-omap: flags=100
    [    5.061147] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    5.061496] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    5.089779]  remoteproc1: registered virtio1 (type 7)
    [    5.159347] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0
    [    5.296794] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.304018] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.309334] ahci 4a140000.sata: forcing port_map 0x0 -> 0x1
    [    5.309379] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
    [    5.309389] ahci 4a140000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst
    [    5.353718] CAN device driver interface
    [    5.431211] scsi host0: ahci
    [    5.434490] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 347
    [    5.447787] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.491596] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
    [    5.509469] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.515799] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.697724] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.703949] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.885968] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    udevd[619]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    udevd[622]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory[    6.521364] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    
    
    [    6.522740] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
    [    6.523824] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3
    udevd[632]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    udevd[631]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    [    6.572664] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.580392] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.598777] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.604997] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    udevd[635]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    [    6.674951] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.742146] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3
    [    6.742315] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.742319] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.742379] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.767522] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.773739] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.778761] pinctrl-single 4a003400.pinmux: pin 4a0037d0.0 already requested by 4806a000.serial; cannot claim for 4ae3c000.can
    [    6.778768] pinctrl-single 4a003400.pinmux: pin-244 (4ae3c000.can) status -22
    [    6.778776] pinctrl-single 4a003400.pinmux: could not request pin 244 (4a0037d0.0) from group dcan1_pins_sleep  on device pinctrl-single
    [    6.778781] c_can_platform 4ae3c000.can: Error applying setting, reverse things back
    [    6.779620] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=367)
    [    6.799069] [drm] Initialized pvr 1.14.3699939 20110701 on minor 1
    [    6.864750] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.877872] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    6.889538] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    6.903924] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.052233]  remoteproc2: powering up 40800000.dsp
    [    7.062233]  remoteproc2: Booting fw image dra7-dsp1-fw.xe66, size 929770
    [    7.075814] omap_hwmod: mmu0_dsp1: _wait_target_disable failed
    [    7.081713] omap-iommu 40d01000.mmu: 40d01000.mmu: version 3.0
    [    7.087676] omap-iommu 40d02000.mmu: 40d02000.mmu: version 3.0
    [    7.150509]  remoteproc2: remote processor 40800000.dsp is now up
    [    7.157127] virtio_rpmsg_bus virtio0: rpmsg host is online
    [    7.162697] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x36
    [    7.170809] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.177022] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.183402] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x37
    [    7.191342] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x3b
    [    7.191481] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.204775]  remoteproc1: powering up 55020000.ipu
    [    7.215526]  remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 3484972
    [    7.222805] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1
    [    7.289460]  remoteproc1: remote processor 55020000.ipu is now up
    [    7.296421] virtio_rpmsg_bus virtio1: rpmsg host is online
    [    7.301984] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x3b
    [    7.309293] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.315502] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.330607] rpmsg_rpc rpmsg2: probing service rpmsg-dce-dsp with src 1024 dst 59
    [    7.337861] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.338203] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.338207] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.338258] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.363717] rpmsg_rpc rpmsg3: probing service rpmsg-dce with src 1024 dst 59
    [    7.363981] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.363986] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.364037] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.364133] rpmsg_rpc rpmsg2: published functions = 8
    [    7.395425] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.401975] rpmsg_rpc rpmsg3: published functions = 8
    [    7.406225] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.406304] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.557022] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.557531] dwc3 48910000.usb: failed to register ULPI interface
    [    7.557561] dwc3: probe of 48910000.usb failed with error -110
    [    7.579085] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.585405] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    7.588391] usbcore: registered new interface driver usbfs
    [    7.588998] usbcore: registered new interface driver hub
    [    7.589636] usbcore: registered new device driver usb
    [    7.597673] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    7.597698] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
    [    7.603740] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010
    [    7.603798] xhci-hcd xhci-hcd.0.auto: irq 445, io mem 0x48890000
    [    7.604928] hub 1-0:1.0: USB hub found
    [    7.604966] hub 1-0:1.0: 1 port detected
    [    7.605385] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    7.605399] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
    [    7.605485] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
    [    7.606482] hub 2-0:1.0: USB hub found
    [    7.606518] hub 2-0:1.0: 1 port detected
    [    7.606987] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
    [    7.607011] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
    [    7.607421] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010
    [    7.607469] xhci-hcd xhci-hcd.1.auto: irq 446, io mem 0x488d0000
    [    7.608516] hub 3-0:1.0: USB hub found
    [    7.608552] hub 3-0:1.0: 1 port detected
    [    7.608942] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
    [    7.608956] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
    [    7.609040] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
    [    7.610038] hub 4-0:1.0: USB hub found
    [    7.610073] hub 4-0:1.0: 1 port detected
    [    7.738006] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    7.744218] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    7.750564] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [   15.497208] ata1: softreset failed (1st FIS failed)
    [   25.507206] ata1: softreset failed (1st FIS failed)
    [   25.857213] ata1: SATA link down (SStatus 0 SControl 300)
    [   25.911882] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
    Starting Bootlog daemon: bootlogd.
    [   25.991990] random: dd: uninitialized urandom read (512 bytes read, 82 bits of entropy available)
    ALSA: Restoring mixer settings...
    No state is present for card DRA7xxEVMMCASP1
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP1
    No state is present for card DRA7xxEVMMCASP2
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP2
    No state is present for card DRA7xxEVMMCASP3
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP3
    No state is present for card DRA7xxEVMMCASP4
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP4
    No state is present for card DRA7xxEVMMCASP8
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP8
    Thu Sep  3 18:41:00 UTC 2015
    
    
    
    2017.11.23 15:00
    
    
    
    This version is for J6
    
    
    
    ****** This application only support ASCII code 0 to 127 ******
    
    
    
    ****** This application only support CB version #F ******
    [   41.433664] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   41.439692] usb usb4: USB disconnect, device number 1
    [   41.447339] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
    [   41.453060] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   41.458641] usb usb3: USB disconnect, device number 1
    [   41.469097] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
    [   41.476486] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   41.481618] usb usb2: USB disconnect, device number 1
    [   41.489682] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
    [   41.495391] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   41.500510] usb usb1: USB disconnect, device number 1
    [   41.508540] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
    [   41.627843] usbcore: deregistering device driver usb
    [   41.634408] usbcore: deregistering interface driver usbfs
    [   41.645342] usbcore: deregistering interface driver hub
    [AB_server.c, make_sure_usb_kernel_stack_removed, 374] temp: drwxr-xr-x   27 root     root             0 Jan  1  1970 .
    dr-xr-xr-x   12 root     root             0 Jan  1  1970 ..
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ac97
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clockevents
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clocksource
    drwxr-xr-x    4 root     root             0 Jan  1  1970 container
    drwxr-xr-x    4 root     root             0 Jan  1  1970 cpu
    drwxr-xr-x    4 root     root             0 Jan  1  1970 edac
    drwxr-xr-x    4 root     root             0 Jan  1  1970 event_source
    drwxr-xr-x    4 root     root             0 Jan  1  1970 hid
    drwxr-xr-x    4 root     root             0 Jan  1  1970 i2c
    drwxr-xr-x    4 root     root             0 Jan  1  1970 iio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mdio_bus
    drwxr-xr-x    4 root     root             0 Jan  1  1970 media
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mipi-dsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mmc
    drwxr-xr-x    5 root     root             0 Jan  1  1970 pci
    drwxr-xr-x    4 root     root             0 Jan  1  1970 platform
    drwxr-xr-x    4 root     root             0 Jan  1  1970 rpmsg
    drwxr-xr-x    4 root     root             0 Jan  1  1970 scsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 sdio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 serio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 soc
    drwxr-xr-x    4 root     root             0 Jan  1  1970 spi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ulpi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 virtio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 workqueue
    
    [AB_server.c, AB_boot_finish, 181] AB boot success, pull high GPIO
    [AB_server.c, AB_boot_finish, 187] AB boot success, pull high GPIO finished
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    /usr/local/bin/set_unused_gpio_input: line 14: echo: write error: Device or resource busy
    /usr/local/bin/set_unused_gpio_input: line 15: /sys/class/gpio/gpio161/direction: No such file or directory
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    INIT: Entering runlevel: 5
    Configuring network interfaces... [   43.330140] net eth0: initializing cpsw version 1.15 (0)
    [   43.335508] net eth0: initialized cpsw ale version 1.4
    [   43.341101] net eth0: ALE Table size 1024
    [   43.348183] libphy: PHY 48485000.mdio:02 not found
    [   43.353001] net eth0: phy "48485000.mdio:02" not found on slave 0, err -19
    [   43.366926] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    /bin/sh: udhcpc: command not found
    done.
    Starting system message bus: [   43.423376] random: dbus-daemon: uninitialized urandom read (12 bytes read, 106 bits of entropy available)
    [   43.439586] random: dbus-daemon: uninitialized urandom read (12 bytes read, 106 bits of entropy available)
    dbus.
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (4) Bytes
    
    
    _version[0]: 30
    _version[1]: 31
    _version[2]: 31
    _version[3]: 30
    _version[4]: 0
    _version[5]: 0
    _version[6]: 0
    _version[7]: 0
    _version[8]: 0
    _version[9]: 0
    _version[10]: 0
    _version[11]: 0
    _version[12]: 0
    _version[13]: 0
    _version[14]: 0
    _version[15]: 0
    [AB_server.c, main, 517] AB_server: get CB's HW version 0110
    
    
    [AB_server.c, get_CB_hardware_version_finish, 254] AB get CB hw version finish, gpio pull low
    [AB_server.c, send_AB_model_info_to_CB, 279] write AB model info total (6) Bytes, model: (DRA74X
    )
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    UIM SYSFS Node Not Found
    Starting telnet daemon.
    Starting tiipclad daemon[AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 1
     ______
    [AB_server.c, sync_CB_status, 312] ______ AB GPIO 109 1, can go ______
    
    GateMP support enabled on host
    
    Opened log file: lad.txt
    
    numProcessors = 5 id = 0 baseId = 0
    
    Spawned daemon: /usr/bin/lad_dra7xx
    
    .
    Starting rpcbind daemon...done.
    creating NFS state directory: done
    starting statd: done
    NFS daemon support not enabled in kernel
    Starting syslogd/klogd: done
    Starting thttpd.
    Enabling thermal zones...
    Stopping Bootlog daemon: bootlogd.
    
    root@wnc-j6:~# [AB_server.c, main, 550] ulpi on/off : J6, ULPI test on
    cat /sys/kernel/debug/mmc0/i[   54.779077] random: nonblocking pool is initialized
    os
    clock:          52000000 Hz
    vdd:            7 (1.65 - 1.95 V)
    bus mode:       2 (push-pull)
    chip select:    0 (don't care)
    power mode:     2 (on)
    bus width:      2 (4 bits)
    timing spec:    1 (mmc high-speed)
    signal voltage: 0 (1.80 V)
    driver type:    0 (driver type B)
    root@wnc-j6:~# lsblk
    NAME         MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
    mmcblk0boot0 179:16   0  128K  1 disk
    mmcblk0boot1 179:32   0  128K  1 disk
    mmcblk1boot0 179:64   0  128K  1 disk
    mmcblk1boot1 179:80   0  128K  1 disk
    mmcblk0      179:0    0  7.3G  0 disk
    `-mmcblk0p1  179:1    0  7.3G  0 part
    mmcblk1      179:48   0  7.3G  0 disk
    |-mmcblk1p1  179:49   0   64M  0 part
    `-mmcblk1p2  179:50   0  7.2G  0 part /
    mmcblk2      179:96   0  3.7G  0 disk
    |-mmcblk2p1  179:97   0   62M  0 part
    `-mmcblk2p2  179:98   0  3.6G  0 part
    root@wnc-j6:~#

    * DRA746 eMMC? Boots ,但安装 eMMC1接口(包括 TS3A27518?)

    U-Boot SPL 2016.05 (Nov 24 2017 - 15:38:03)
    DRA752-GP ES2.0
    *** Warning - bad CRC, using default environment
    
    Trying to boot from MMC2_2
    spl: falcon_args_file not set in environment, falling back to default
    reading args
    spl_load_image_fat_os: error reading image args, err - -1
    reading u-boot.img
    reading u-boot.img
    
    
    U-Boot 2016.05 (Nov 24 2017 - 15:38:03 +0800)
    
    CPU  : DRA752-GP ES2.0
    Board: DRA74x EVM REV
    I2C:   ready
    DRAM:  2 GiB
    MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
    *** Warning - bad CRC, using default environment
    
    Warning: fastboot.board_rev: unknown board revision
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid GPT ***
    GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
    part_get_info_efi: *** ERROR: Invalid Backup GPT ***
    ERROR: cannot find partition: 'userdata'
    
    at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size()
    Warning: fastboot.userdata_size: unable to calc
    Net:   <ethaddr> not set. Validating first E-fuse MAC
    Could not get PHY for cpsw: addr 2
    cpsw
    Hit any key to stop autoboot:  0
    J6 ...
    switch to partitions #0, OK
    mmc1(part 0) is current device
    SD/MMC found on device 1
    4281344 bytes read in 214 ms (19.1 MiB/s)
    113603 bytes read in 12 ms (9 MiB/s)
    Booting from mmc1 ...
    Kernel image @ 0x82000000 [ 0x000000 - 0x415400 ]
    ## Flattened Device Tree blob at 88000000
       Booting using the fdt blob at 0x88000000
       Loading Device Tree to 8ffe1000, end 8ffffbc2 ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpuset
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Initializing cgroup subsys cpuacct
    [    0.000000] Linux version 4.4.45 (bowei@bowei-Veriton-M490) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #75 SMP PREEMPT Mon Jan 22 10:50:18 CST 2018
    [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [    0.000000] Machine model: TI DRA742 Bowei 20170929 17:30
    [    0.000000] Reserved memory: created CMA memory pool at 0x95800000, size 56 MiB
    [    0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x99000000, size 64 MiB
    [    0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9d000000, size 32 MiB
    [    0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x9f000000, size 8 MiB
    [    0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool
    [    0.000000] cma: Reserved 24 MiB at 0xfd400000
    [    0.000000] Memory policy: Data cache writealloc
    [    0.000000] OMAP4: Map 0xfee00000 to fe600000 for dram barrier
    [    0.000000] DRA752 ES2.0
    [    0.000000] PERCPU: Embedded 12 pages/cpu @eed51000 s18944 r8192 d22016 u49152
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 516672
    [    0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=bddb4f41-02 rw rootfstype=ext4 rootwait consoleblank=0 omapdrm.num_crtc=2 drm.debug=0xff
    [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Memory: 1851432K/2073600K available (7719K kernel code, 797K rwdata, 4560K rodata, 372K init, 291K bss, 33752K reserved, 188416K cma-reserved, 1266688K highmem)
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    [    0.000000]       .text : 0xc0008000 - 0xc0c0607c   (12281 kB)
    [    0.000000]       .init : 0xc0c07000 - 0xc0c64000   ( 372 kB)
    [    0.000000]       .data : 0xc0c64000 - 0xc0d2b530   ( 798 kB)
    [    0.000000]        .bss : 0xc0d2d000 - 0xc0d75f00   ( 292 kB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] Preemptible hierarchical RCU implementation.
    [    0.000000]  Build-time adjustment of leaf fanout to 32.
    [    0.000000] NR_IRQS:16 nr_irqs:16 16
    [    0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div
    [    0.000000] OMAP clockevent source: timer1 at 31475 Hz
    [    0.000000] Architected cp15 timer(s) running at 5.90MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns
    [    0.000004] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns
    [    0.000015] Switching to timer-based delay loop, resolution 169ns
    [    0.000327] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
    [    0.000334] OMAP clocksource: 32k_counter at 32768 Hz
    [    0.000788] Console: colour dummy device 80x30
    [    0.000805] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
    [    0.000811] This ensures that you still see kernel messages. Please
    [    0.000817] update your kernel commandline.
    [    0.000829] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016)
    [    0.000843] pid_max: default: 32768 minimum: 301
    [    0.000934] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.000944] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [    0.001476] Initializing cgroup subsys io
    [    0.001493] Initializing cgroup subsys memory
    [    0.001517] Initializing cgroup subsys devices
    [    0.001529] Initializing cgroup subsys freezer
    [    0.001540] Initializing cgroup subsys perf_event
    [    0.001551] Initializing cgroup subsys pids
    [    0.001579] CPU: Testing write buffer coherency: ok
    [    0.001775] /cpus/cpu@0 missing clock-frequency property
    [    0.001790] /cpus/cpu@1 missing clock-frequency property
    [    0.001800] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [    0.001840] Setting up static identity map for 0x80008340 - 0x800083a0
    [    0.080064] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [    0.080135] Brought up 2 CPUs
    [    0.080149] SMP: Total of 2 processors activated (23.60 BogoMIPS).
    [    0.080156] CPU: All CPU(s) started in SVC mode.
    [    0.081192] devtmpfs: initialized
    [    0.111040] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
    [    0.112025] omap_hwmod: l3_main_2 using broken dt data from ocp
    [    0.310748] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.314458] pinctrl core: initialized pinctrl subsystem
    [    0.315315] NET: Registered protocol family 16
    [    0.316248] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.340278] cpuidle: using governor ladder
    [    0.370303] cpuidle: using governor menu
    [    0.378533] OMAP GPIO hardware version 0.1
    [    0.382634] GPIO line 161 (radio_rst) hogged as output/low
    [    0.414523] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
    [    0.414534] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.415009] omap4_sram_init:Unable to allocate sram needed to handle errata I688
    [    0.415018] omap4_sram_init:Unable to get sram pool needed to handle errata I688
    [    0.415505] OMAP DMA hardware revision 0.0
    [    0.461690] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
    [    0.462936] edma 43300000.edma: memcpy is disabled
    [    0.467692] edma 43300000.edma: TI EDMA DMA engine driver
    [    0.471903] omap-iommu 40d01000.mmu: 40d01000.mmu registered
    [    0.472083] omap-iommu 40d02000.mmu: 40d02000.mmu registered
    [    0.472245] omap-iommu 58882000.mmu: 58882000.mmu registered
    [    0.472403] omap-iommu 55082000.mmu: 55082000.mmu registered
    [    0.472703] omap-iommu 41501000.mmu: 41501000.mmu registered
    [    0.472889] omap-iommu 41502000.mmu: 41502000.mmu registered
    [    0.474884] SCSI subsystem initialized
    [    0.476142] ======palmas_i2c_probe:526========
    [    0.476159] ======palmas_i2c_probe:559, features=0x0========
    [    0.476464] palmas 0-0058: IRQ missing: skipping irq request
    [    0.491206] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0
    [    0.562945] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
    [    0.563584] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
    [    0.563950] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
    [    0.564309] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
    [    0.564683] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
    [    0.564902] media: Linux media interface: v0.10
    [    0.564958] Linux video capture interface: v2.00
    [    0.564997] pps_core: LinuxPPS API ver. 1 registered
    [    0.565003] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.565026] PTP clock support registered
    [    0.565051] EDAC MC: Ver: 3.0.0
    [    0.565807] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
    [    0.566099] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
    [    0.566445] Advanced Linux Sound Architecture Driver Initialized.
    [    0.567340] clocksource: Switched to clocksource arch_sys_counter
    [    0.578102] NET: Registered protocol family 2
    [    0.578596] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.578659] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.578784] TCP: Hash tables configured (established 8192 bind 8192)
    [    0.578830] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [    0.578863] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [    0.579072] NET: Registered protocol family 1
    [    0.579335] RPC: Registered named UNIX socket transport module.
    [    0.579345] RPC: Registered udp transport module.
    [    0.579351] RPC: Registered tcp transport module.
    [    0.579357] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.580397] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
    [    0.582846] futex hash table entries: 512 (order: 3, 32768 bytes)
    [    0.589537] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.590190] NFS: Registering the id_resolver key type
    [    0.590215] Key type id_resolver registered
    [    0.590222] Key type id_legacy registered
    [    0.590288] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.592263] bounce: pool size: 64 pages
    [    0.592414] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
    [    0.592431] io scheduler noop registered
    [    0.592446] io scheduler deadline registered
    [    0.592480] io scheduler cfq registered (default)
    [    0.597800] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
    [    0.659406] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
    [    0.663036] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 299, base_baud = 3000000) is a 8250
    [    0.663917] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 300, base_baud = 3000000) is a 8250
    [    0.664793] console [ttyS2] disabled
    [    0.664838] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250
    [    1.551629] console [ttyS2] enabled
    [    1.556023] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 302, base_baud = 3000000) is a 8250
    [    1.565752] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 303, base_baud = 3000000) is a 8250
    [    1.575435] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 304, base_baud = 3000000) is a 8250
    [    1.585126] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 305, base_baud = 3000000) is a 8250
    [    1.595260] [drm] Initialized drm 1.1.0 20060810
    [    1.601467] OMAP DSS rev 6.1
    [    1.605234] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
    [    1.627032] brd: module loaded
    [    1.635266] loop: module loaded
    [    1.644960] libphy: Fixed MDIO Bus: probed
    [    1.649677] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
    [    1.656757] e1000: Copyright (c) 1999-2006 Intel Corporation.
    [    1.662607] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    [    1.668478] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    [    1.674482] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k
    [    1.681487] igb: Copyright (c) 2007-2014 Intel Corporation.
    [    1.737371] davinci_mdio 48485000.mdio: davinci mdio revision 1.6
    [    1.743494] davinci_mdio 48485000.mdio: no live phy, scanning all
    [    1.847341] davinci_mdio 48485000.mdio: timed out waiting for user access
    [    1.947340] davinci_mdio 48485000.mdio: timed out waiting for idle
    [    1.953568] davinci_mdio: probe of 48485000.mdio failed with error -5
    [    1.960699] cpsw 48484000.ethernet: Detected MACID = 54:45:38:a7:aa:1e
    [    1.967378] cpsw 48484000.ethernet: cpts: overflow check period 800
    [    1.974347] cpsw 48484000.ethernet: cpsw: Detected MACID = 54:45:38:a7:aa:1f
    [    1.983056] mousedev: PS/2 mouse device common for all mice
    [    1.989285] i2c /dev entries driver
    [    2.007430] tvp5158 1-0058: i2c i/o error: rc == -121 (should be 1)
    [    2.013786] tvp5158 1-0058: i2c i/o error: rc == -121 (should be 1)
    [    2.020121] tvp5158 1-0058: ERROR: Chip id is not TVP5158
    [    2.025658] ov1063x 1-0037: ov1063x Product ID 0 Manufacturer ID 0
    [    2.031886] ov1063x 1-0037: ov1063x 1-0037 sensor driver registered !!
    [    2.039301] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
    [    2.046394] vip 48990000.vip: loading firmware vpdma-1b8.bin
    [    2.057521] vpe 489d0000.vpe: Device registered as /dev/video0
    [    2.067361] vip 48990000.vip: VPDMA firmware loaded
    [    2.072390] vip2-s1: Port B: Using subdev ov1063x 1-0037 for capture
    [    2.079183] vip2-s1: device registered as video1
    [    2.097763] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
    [    2.104148] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
    [    2.110574] omap_hsmmc 480b4000.mmc: no pinctrl state for hs200_1_8v mode
    [    2.117541] evm_3v3_sw: supplied by sysen1
    [    2.157699] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr25 mode
    [    2.164084] omap_hsmmc 480d1000.mmc: no pinctrl state for sdr12 mode
    [    2.170479] omap_hsmmc 480d1000.mmc: no pinctrl state for hs mode
    [    2.208149] ledtrig-cpu: registered to indicate activity on CPUs
    [    2.216249] hwspinlock_user gatemp: requested 10 hwspinlocks
    [    2.237270] pinctrl-single 4a003400.pinmux: pin 4a0036a8.0 already requested by 4806a000.serial; cannot claim for 48460000.mcasp
    [    2.248934] pinctrl-single 4a003400.pinmux: pin-170 (48460000.mcasp) status -22
    [    2.256278] pinctrl-single 4a003400.pinmux: could not request pin 170 (4a0036a8.0) from group mcasp1_pins  on device pinctrl-single
    [    2.268211] davinci-mcasp 48460000.mcasp: Error applying setting, reverse things back
    [    2.276484] davinci-mcasp 48460000.mcasp: Update the bindings to use assigned-clocks!
    [    2.284391] davinci-mcasp 48460000.mcasp: failed to reparent fck
    [    2.290676] pinctrl-single 4a003400.pinmux: pin 4a003700.0 already requested by 4806a000.serial; cannot claim for 48464000.mcasp
    [    2.302305] pinctrl-single 4a003400.pinmux: pin-192 (48464000.mcasp) status -22
    [    2.309687] pinctrl-single 4a003400.pinmux: could not request pin 192 (4a003700.0) from group mcasp2_pins  on device pinctrl-single
    [    2.321575] davinci-mcasp 48464000.mcasp: Error applying setting, reverse things back
    [    2.329828] davinci-mcasp 48464000.mcasp: Update the bindings to use assigned-clocks!
    [    2.337725] davinci-mcasp 48464000.mcasp: failed to reparent fck
    [    2.343977] pinctrl-single 4a003400.pinmux: pin 4a00372c.0 already requested by 4806a000.serial; cannot claim for 48468000.mcasp
    [    2.355607] pinctrl-single 4a003400.pinmux: pin-203 (48468000.mcasp) status -22
    [    2.362959] pinctrl-single 4a003400.pinmux: could not request pin 203 (4a00372c.0) from group mcasp3_pins  on device pinctrl-single
    [    2.374844] davinci-mcasp 48468000.mcasp: Error applying setting, reverse things back
    [    2.383085] davinci-mcasp 48468000.mcasp: Update the bindings to use assigned-clocks!
    [    2.390983] davinci-mcasp 48468000.mcasp: failed to reparent fck
    [    2.397236] pinctrl-single 4a003400.pinmux: pin 4a003734.0 already requested by 4806a000.serial; cannot claim for 4846c000.mcasp
    [    2.408870] pinctrl-single 4a003400.pinmux: pin-205 (4846c000.mcasp) status -22
    [    2.416213] pinctrl-single 4a003400.pinmux: could not request pin 205 (4a003734.0) from group mcasp4_pins  on device pinctrl-single
    [    2.428097] davinci-mcasp 4846c000.mcasp: Error applying setting, reverse things back
    [    2.436336] davinci-mcasp 4846c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.444233] davinci-mcasp 4846c000.mcasp: failed to reparent fck
    [    2.450499] pinctrl-single 4a003400.pinmux: pin 4a003720.0 already requested by 4806a000.serial; cannot claim for 4847c000.mcasp
    [    2.462128] pinctrl-single 4a003400.pinmux: pin-200 (4847c000.mcasp) status -22
    [    2.469480] pinctrl-single 4a003400.pinmux: could not request pin 200 (4a003720.0) from group mcasp8_pins  on device pinctrl-single
    [    2.481364] davinci-mcasp 4847c000.mcasp: Error applying setting, reverse things back
    [    2.489611] davinci-mcasp 4847c000.mcasp: Update the bindings to use assigned-clocks!
    [    2.497508] davinci-mcasp 4847c000.mcasp: failed to reparent fck
    [    2.504692] NET: Registered protocol family 10
    [    2.519972] sit: IPv6 over IPv4 tunneling driver
    [    2.525148] NET: Registered protocol family 17
    [    2.529873] Key type dns_resolver registered
    [    2.534292] omap_voltage_late_init: Voltage driver support not added
    [    2.541209] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    2.548563] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    2.554817] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    2.561455] Power Management for TI OMAP4+ devices.
    [    2.566591] Registering SWP/SWPB emulation handler
    [    2.574136] dmm 4e000000.dmm: initialized all PAT entries
    [    2.601001] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [    2.607679] [drm] No driver support for vblank timestamp query.
    [    2.624846] [drm] Enabling DMM ywrap scrolling
    [    2.680497] mmc0: MAN_BKOPS_EN bit is not set
    [    2.682910] mmc0: switch to bus width 1 failed
    [    2.699844] Console: switching to colour frame buffer device 240x67
    [    2.729767] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
    [    2.745328] mmc0: new high speed MMC card at address 0001
    [    2.761270] mmcblk0: mmc0:0001 R1J55A 7.28 GiB
    [    2.768647] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
    [    2.776079] mmcblk0boot0: mmc0:0001 R1J55A partition 1 128 KiB
    [    2.782184] mmcblk0boot1: mmc0:0001 R1J55A partition 2 128 KiB
    [    2.789519] asoc-simple-card-mcasp1 sound@1: bt-sco-pcm-mcasp1 <-> 48460000.mcasp mapping ok
    [    2.798021] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    2.807739] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPLOUT
    [    2.817587] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    2.827021] mmcblk0: retrying using single block read
    [    2.832138] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.841761] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for HPROUT
    [    2.849575] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.859358] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    2.868642] blk_update_request: I/O error, dev mmcblk0, sector 0
    [    2.868655] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for LLOUT
    [    2.868662] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.868667] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for RLOUT
    [    2.868672] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.868677] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3L
    [    2.868682] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.868687] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for MIC3R
    [    2.868692] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.868697] asoc-simple-card-mcasp1 sound@1: ASoC: no source widget found for Mic Bias
    [    2.868701] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.868707] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1L
    [    2.868712] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.868717] asoc-simple-card-mcasp1 sound@1: ASoC: no sink widget found for LINE1R
    [    2.868722] asoc-simple-card-mcasp1 sound@1: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.880987] asoc-simple-card-mcasp2 sound@2: bt-sco-pcm-mcasp2 <-> 48464000.mcasp mapping ok
    [    2.880996] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPLOUT
    [    2.881001] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.881006] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for HPROUT
    [    2.881011] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.881016] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for LLOUT
    [    2.881022] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.881028] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for RLOUT
    [    2.881033] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.881038] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3L
    [    2.881043] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.881048] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for MIC3R
    [    2.881053] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.881058] asoc-simple-card-mcasp2 sound@2: ASoC: no source widget found for Mic Bias
    [    2.881063] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.881068] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1L
    [    2.881073] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.881077] asoc-simple-card-mcasp2 sound@2: ASoC: no sink widget found for LINE1R
    [    2.881082] asoc-simple-card-mcasp2 sound@2: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.883098] asoc-simple-card-mcasp3 sound@3: bt-sco-pcm-mcasp3 <-> 48468000.mcasp mapping ok
    [    2.883107] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPLOUT
    [    2.883112] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.883118] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for HPROUT
    [    2.883122] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.883127] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for LLOUT
    [    2.883132] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.883138] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for RLOUT
    [    2.883143] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.883148] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3L
    [    2.883153] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.883158] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for MIC3R
    [    2.883162] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.883167] asoc-simple-card-mcasp3 sound@3: ASoC: no source widget found for Mic Bias
    [    2.883172] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.883177] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1L
    [    2.883182] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.883187] asoc-simple-card-mcasp3 sound@3: ASoC: no sink widget found for LINE1R
    [    2.883191] asoc-simple-card-mcasp3 sound@3: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.885254] asoc-simple-card-mcasp4 sound@4: bt-sco-pcm-mcasp4 <-> 4846c000.mcasp mapping ok
    [    2.885262] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPLOUT
    [    2.885268] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.885273] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for HPROUT
    [    2.885279] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.885284] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for LLOUT
    [    2.885290] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.885295] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for RLOUT
    [    2.885300] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.885305] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3L
    [    2.885310] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.885314] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for MIC3R
    [    2.885319] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.885324] asoc-simple-card-mcasp4 sound@4: ASoC: no source widget found for Mic Bias
    [    2.885328] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.885334] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1L
    [    2.885339] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.885344] asoc-simple-card-mcasp4 sound@4: ASoC: no sink widget found for LINE1R
    [    2.885349] asoc-simple-card-mcasp4 sound@4: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.887766] asoc-simple-card-mcasp8 sound@8: bt-sco-pcm-mcasp8 <-> 4847c000.mcasp mapping ok
    [    2.887775] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPLOUT
    [    2.887780] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPLOUT -> direct -> Headphone Jack
    [    2.887786] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for HPROUT
    [    2.887791] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route HPROUT -> direct -> Headphone Jack
    [    2.887796] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for LLOUT
    [    2.887801] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route LLOUT -> direct -> Line Out
    [    2.887806] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for RLOUT
    [    2.887811] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route RLOUT -> direct -> Line Out
    [    2.887816] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3L
    [    2.887820] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3L
    [    2.887825] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for MIC3R
    [    2.887829] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Jack -> direct -> MIC3R
    [    2.887834] asoc-simple-card-mcasp8 sound@8: ASoC: no source widget found for Mic Bias
    [    2.887839] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Mic Bias -> direct -> Mic Jack
    [    2.887844] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1L
    [    2.887848] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1L
    [    2.887853] asoc-simple-card-mcasp8 sound@8: ASoC: no sink widget found for LINE1R
    [    2.887858] asoc-simple-card-mcasp8 sound@8: ASoC: Failed to add route Line In -> direct -> LINE1R
    [    2.888877] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    2.888880] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    2.888940] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    2.898610] hctosys: unable to open rtc device (rtc0)
    [    2.913245] aic_dvdd: disabling
    [    2.932189] ldousb: disabling
    [    2.982904] ALSA device list:
    [    2.982908]   #0: DRA7xx-EVM-MCASP1
    [    2.982911]   #1: DRA7xx-EVM-MCASP2
    [    2.982913]   #2: DRA7xx-EVM-MCASP3
    [    2.982916]   #3: DRA7xx-EVM-MCASP4
    [    2.982918]   #4: DRA7xx-EVM-MCASP8
    [    3.686889] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    3.696185] blk_update_request: I/O error, dev mmcblk0, sector 1
    [    3.702414] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    3.711698] blk_update_request: I/O error, dev mmcblk0, sector 2
    [    3.717930] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    3.727190] blk_update_request: I/O error, dev mmcblk0, sector 3
    [    3.733426] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    3.742704] blk_update_request: I/O error, dev mmcblk0, sector 4
    [    3.748936] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    3.758212] blk_update_request: I/O error, dev mmcblk0, sector 5
    [    3.764427] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    3.773700] blk_update_request: I/O error, dev mmcblk0, sector 6
    [    3.779925] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    3.789201] blk_update_request: I/O error, dev mmcblk0, sector 7
    [    3.795236] Buffer I/O error on dev mmcblk0, logical block 0, async page read
    [    3.802602] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    3.811756] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    3.821206] mmcblk0: retrying using single block read
    [    3.826458] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    3.835732] blk_update_request: I/O error, dev mmcblk0, sector 0
    [    3.841953] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    3.851230] blk_update_request: I/O error, dev mmcblk0, sector 1
    [    3.857446] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    3.866885] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    3.876337] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    3.885797] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    3.895249] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    3.904704] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    3.913983] Buffer I/O error on dev mmcblk0, logical block 0, async page read
    [    3.921172]  mmcblk0: unable to read partition table
    [    3.927519] Waiting for root device PARTUUID=bddb4f41-02...
    [    3.927595] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    3.927599] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    3.927652] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    3.990491] mmc1: MAN_BKOPS_EN bit is not set
    [    4.099283] mmc1: new DDR MMC card at address 0001
    [    4.104543] mmcblk1: mmc1:0001 R1J55A 7.28 GiB
    [    4.119371] mmcblk1boot0: mmc1:0001 R1J55A partition 1 128 KiB
    [    4.135483] mmcblk1boot1: mmc1:0001 R1J55A partition 2 128 KiB
    [    4.142371]  mmcblk1: p1 p2
    [    4.146693] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    4.153034] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    4.159341] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    4.197251] EXT4-fs (mmcblk1p2): recovery complete
    [    4.202499] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
    [    4.210690] VFS: Mounted root (ext4 filesystem) on device 179:50.
    [    4.218233] devtmpfs: mounted
    [    4.221434] Freeing unused kernel memory: 372K (c0c07000 - c0c64000)
    [    4.227856] This architecture does not have kernel memory protection.
    [    4.241563] mmc2: host does not support reading read-only switch, assuming write-enable
    [    4.249694] mmc2: new SDHC card at address 0001
    [    4.254638] mmcblk2: mmc2:0001 SD4GB 3.64 GiB
    [    4.260955]  mmcblk2: p1 p2
    [    4.264566] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    4.270865] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    4.270929] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    INIT: version 2.88 booting
    Starting udev
    [    4.552320] udevd[129]: starting version 182
    [    4.731554] omap-rproc 58820000.ipu: assigned reserved memory node ipu1_cma@9d000000
    [    4.857486]  remoteproc0: 58820000.ipu is available
    [    4.862418]  remoteproc0: Note: remoteproc is still under development and considered experimental.
    [    5.037117]  remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.201575]  remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2
    [    5.207640] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.207645] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.207709] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.229078] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@95800000
    [    5.337466]  remoteproc1: 55020000.ipu is available
    [    5.342383]  remoteproc1: Note: remoteproc is still under development and considered experimental.
    [    5.489896]  remoteproc0: failed to load dra7-ipu1-fw.xem4
    [    5.500558]  remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.583597] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@99000000
    [    5.583681] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.583686] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.583748] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.639004]  remoteproc2: 40800000.dsp is available
    [    5.643951] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    5.653192] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0x0
    [    5.653198] mmcblk0: retrying using single block read
    [    5.668254] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0x0
    [    5.678210] mmcblk0: error -84 transferring data, sector 15269761, nr 7, cmd response 0x900, card status 0x0
    [    5.719653] CAN device driver interface
    [    5.737930] mmcblk0: error -84 transferring data, sector 15269762, nr 6, cmd response 0x900, card status 0x0
    [    5.745950]  remoteproc2: Note: remoteproc is still under development and considered experimental.
    [    5.745955]  remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.747055] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9f000000
    [    5.747112]  remoteproc3: 41000000.dsp is available
    [    5.747115]  remoteproc3: Note: remoteproc is still under development and considered experimental.
    [    5.747118]  remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
    [    5.751380] pinctrl-single 4a003400.pinmux: pin 4a0037d0.0 already requested by 4806a000.serial; cannot claim for 4ae3c000.can
    [    5.751388] pinctrl-single 4a003400.pinmux: pin-244 (4ae3c000.can) status -22
    [    5.751396] pinctrl-single 4a003400.pinmux: could not request pin 244 (4a0037d0.0) from group dcan1_pins_sleep  on device pinctrl-single
    [    5.751400] c_can_platform 4ae3c000.can: Error applying setting, reverse things back
    [    5.752239] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=367)
    [    5.757730] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.757734] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.757795] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.784380]  remoteproc1: registered virtio0 (type 7)
    [    5.784988]  remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2
    [    5.784994]  remoteproc3: failed to load dra7-dsp2-fw.xe66
    [    5.787759]  remoteproc2: registered virtio1 (type 7)
    [    5.814972] [drm] Initialized pvr 1.14.3699939 20110701 on minor 1
    [    5.816385] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.816390] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.816454] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    5.915905] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20
    [    5.916023] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
    [    5.923383] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    [    5.923388] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
    [    5.923445] ti_oppdm 4a003b20.oppdm: Unable to get vdd regulator:-517
    [    6.018191] mmcblk0: error -84 transferring data, sector 15269763, nr 5, cmd response 0x900, card status 0x0
    [    6.018559] mmcblk0: error -84 transferring data, sector 15269764, nr 4, cmd response 0x900, card status 0x0
    [    6.018945] mmcblk0: error -84 transferring data, sector 15269765, nr 3, cmd response 0x900, card status 0x0
    [    6.018972] alg: skcipher: setkey failed on test 5 for ecb-des-omap: flags=100
    [    6.019921] mmcblk0: error -84 transferring data, sector 15269766, nr 2, cmd response 0x900, card status 0x0
    [    6.020140] mmcblk0: error -84 transferring data, sector 15269767, nr 1, cmd response 0x900, card status 0x0
    [    6.020268] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    6.020340] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.038687] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0xb00
    [    6.038692] mmcblk0: retrying using single block read
    [    6.039368] mmcblk0: error -84 transferring data, sector 15269760, nr 8, cmd response 0x900, card status 0x0
    [    6.041806] mmcblk0: error -84 transferring data, sector 15269761, nr 7, cmd response 0x900, card status 0x0
    [    6.041968] mmcblk0: error -84 transferring data, sector 15269762, nr 6, cmd response 0x900, card status 0x0
    [    6.042083] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
    [    6.042145] mmcblk0: error -84 transferring data, sector 15269763, nr 5, cmd response 0x900, card status 0x0
    [    6.042296] mmcblk0: error -84 transferring data, sector 15269764, nr 4, cmd response 0x900, card status 0x0
    [    6.042459] mmcblk0: error -84 transferring data, sector 15269765, nr 3, cmd response 0x900, card status 0x0
    [    6.042614] mmcblk0: error -84 transferring data, sector 15269766, nr 2, cmd response 0x900, card status 0x0
    [    6.042780] mmcblk0: error -84 transferring data, sector 15269767, nr 1, cmd response 0x900, card status 0x0
    [    6.042790] Buffer I/O error on dev mmcblk0, logical block 1908720, async page read
    [    6.043014] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.043093] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0xb00
    [    6.043097] mmcblk0: retrying using single block read
    [    6.043256] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0x0
    [    6.043418] mmcblk0: error -84 transferring data, sector 15269873, nr 7, cmd response 0x900, card status 0x0
    [    6.043545] mmcblk0: error -84 transferring data, sector 15269874, nr 6, cmd response 0x900, card status 0x0
    [    6.043701] mmcblk0: error -84 transferring data, sector 15269875, nr 5, cmd response 0x900, card status 0x0
    [    6.043829] mmcblk0: error -84 transferring data, sector 15269876, nr 4, cmd response 0x900, card status 0x0
    [    6.043964] mmcblk0: error -84 transferring data, sector 15269877, nr 3, cmd response 0x900, card status 0x0
    [    6.044091] mmcblk0: error -84 transferring data, sector 15269878, nr 2, cmd response 0x900, card status 0x0
    [    6.044250] mmcblk0: error -84 transferring data, sector 15269879, nr 1, cmd response 0x900, card status 0x0
    [    6.044420] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.044483] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0xb00
    [    6.044487] mmcblk0: retrying using single block read
    [    6.044610] mmcblk0: error -84 transferring data, sector 15269872, nr 8, cmd response 0x900, card status 0x0
    [    6.044738] mmcblk0: error -84 transferring data, sector 15269873, nr 7, cmd response 0x900, card status 0x0
    [    6.044861] mmcblk0: error -84 transferring data, sector 15269874, nr 6, cmd response 0x900, card status 0x0
    [    6.044985] mmcblk0: error -84 transferring data, sector 15269875, nr 5, cmd response 0x900, card status 0x0
    [    6.045111] mmcblk0: error -84 transferring data, sector 15269876, nr 4, cmd response 0x900, card status 0x0
    [    6.045236] mmcblk0: error -84 transferring data, sector 15269877, nr 3, cmd response 0x900, card status 0x0
    [    6.045368] mmcblk0: error -84 transferring data, sector 15269878, nr 2, cmd response 0x900, card status 0x0
    [    6.045493] mmcblk0: error -84 transferring data, sector 15269879, nr 1, cmd response 0x900, card status 0x0
    [    6.045500] Buffer I/O error on dev mmcblk0, logical block 1908734, async page read
    [    6.045705] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.045760] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    6.045763] mmcblk0: retrying using single block read
    [    6.045945] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    6.046129] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    6.046307] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    6.046492] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    6.046674] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    6.046850] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    6.047024] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    6.047198] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    6.047379] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.047430] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    6.047434] mmcblk0: retrying using single block read
    [    6.047615] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    6.047794] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    6.047970] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    6.048144] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    6.048319] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    6.048498] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    6.048674] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    6.048848] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    6.048856] Buffer I/O error on dev mmcblk0, logical block 0, async page read
    [    6.049125] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    6.049173] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    6.049176] mmcblk0: retrying using single block read
    [    6.049355] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    [    6.049537] mmcblk0: error -84 transferring data, sector 9, nr 7, cmd response 0x900, card status 0x0
    [    6.049718] mmcblk0: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    [    6.049900] mmcblk0: error -84 transferring data, sector 11, nr 5, cmd response 0x900, card status 0x0
    [    6.050082] mmcblk0: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    [    6.050264] mmcblk0: error -84 transferring data, sector 13, nr 3, cmd response 0x900, card status 0x0
    [    6.057238] mmcblk0: error -84 transferring data, sector 14, nr 2, cmd response 0x900, card status 0x0
    [    6.058705] mmcblk0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    [    6.058715] Buffer I/O error on dev mmcblk0, logical block 1, async page read
    [    6.059005] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 52 printk messages dropped ** [    6.065593] mmcblk0: error -84 transferring data, sector 15269882, nr 6, cmd response 0x900, card status 0x0
    ** 18 printk messages dropped ** [    6.069256] mmcblk0: retrying using single block read
    ** 3 printk messages dropped ** [    6.069802] mmcblk0: error -84 transferring data, sector 15269827, nr 5, cmd response 0x900, card status 0x0
    ** 14 printk messages dropped ** [    6.071657] mmcblk0: error -84 transferring data, sector 15269879, nr 1, cmd response 0x900, card status 0x0
    ** 12 printk messages dropped ** [    6.073786] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    6.073789] mmcblk0: retrying using single block read
    ** 7 printk messages dropped ** [    6.075318] mmcblk0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    ** 11 printk messages dropped ** [    6.116558] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    6.120261] mmcblk0: retrying using single block read
    ** 22 printk messages dropped ** [    6.123844] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 17 printk messages dropped ** [    6.126763] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 7 printk messages dropped ** [    6.128098] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
    ** 74 printk messages dropped ** [    6.147089] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 129 printk messages dropped ** [    6.169535] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 118 printk messages dropped ** [    6.219804] mmcblk0: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 33 printk messages dropped ** [    6.225384] mmcblk0: error -84 transferring data, sector 61, nr 3, cmd response 0x900, card status 0x0
    ** 38 printk messages dropped ** [    6.249558] mmcblk0: error -84 transferring data, sector 120, nr 8, cmd response 0x900, card status 0x0
    ** 31 printk messages dropped ** [    6.308644] mmcblk0: retrying using single block read
    ** 20 printk messages dropped ** [    6.435325] mmcblk0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    ** 45 printk messages dropped ** [    6.615830] mmcblk0: error -84 transferring data, sector 56, nr 8, cmd response 0x900, card status 0x0
    ** 28 printk messages dropped ** [    6.679610] mmcblk0: error -84 transferring data, sector 127, nr 1, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    6.723007] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 31 printk messages dropped ** [    6.765942] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
    ** 20 printk messages dropped ** [    6.781631] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    6.786248] mmcblk0: error -84 transferring data, sector 134, nr 2, cmd response 0x900, card status 0x0
    ** 34 printk messages dropped ** [    6.871495] mmcblk0: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    ** 31 printk messages dropped ** [    6.926403] mmcblk0: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    ** 27 printk messages dropped ** [    6.948468] mmcblk0: retrying using single block read
    ** 21 printk messages dropped ** [    6.952079] mmcblk0: retrying using single block read
    ** 21 printk messages dropped ** [    6.955778] mmcblk0: retrying using single block read
    ** 26 printk messages dropped ** [    6.969841] mmcblk0: error -84 transferring data, sector 260, nr 4, cmd response 0x900, card status 0x0
    ** 42 printk messages dropped ** [    6.976413] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 34 printk messages dropped ** [    6.991654] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 31 printk messages dropped ** [    7.005727] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.010401] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 30 printk messages dropped ** [    7.015684] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.025203] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 25 printk messages dropped ** [    7.029420] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.048313] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.052102] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.068499] mmcblk0: retrying using single block read
    ** 15 printk messages dropped ** [    7.079640] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.118820] mmcblk0: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.136739] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.156549] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 21 printk messages dropped ** [    7.166335] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.192523] mmcblk0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.210238] mmcblk0: retrying using single block read
    ** 16 printk messages dropped ** [    7.213104] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.217209] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    7.220633] mmcblk0: retrying using single block read
    ** 17 printk messages dropped ** [    7.223560] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.227328] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.231222] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.235646] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.240086] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.244258] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.248282] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.252922] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.266619] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 30 printk messages dropped ** [    7.283300] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.296234] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.308987] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.317826] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x3b
    ** 19 printk messages dropped ** [    7.328665] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    7.339639] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    7.375730] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.387996] mmcblk0boot0: retrying using single block read
    ** 15 printk messages dropped ** [    7.396588] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.410223] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.422433] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.434769] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.448173] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.457492] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.470932] mmcblk0boot1: retrying using single block read
    ** 19 printk messages dropped ** [    7.485725] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.496512] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.507213] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.515723] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.528630] hub 2-0:1.0: 1 port detected
    ** 14 printk messages dropped ** [    7.530561] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.542362] hub 3-0:1.0: USB hub found
    ** 13 printk messages dropped ** [    7.545214] mmcblk0boot0: retrying using single block read
    ** 16 printk messages dropped ** [    7.554414] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.564891] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.580896] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.593840] mmcblk0boot0: retrying using single block read
    ** 15 printk messages dropped ** [    7.602451] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.614720] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.626842] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 26 printk messages dropped ** [    7.640057] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.652295] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.665124] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.677741] mmcblk0boot0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    ** 24 printk messages dropped ** [    7.689811] mmcblk0boot0: error -84 transferring data, sector 25, nr 7, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.703497] mmcblk0boot0: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.715515] mmcblk0boot0: error -84 transferring data, sector 62, nr 2, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.727552] mmcblk0boot0: retrying using single block read
    ** 15 printk messages dropped ** [    7.736586] mmcblk0boot1: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.749156] mmcblk0boot1: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.760599] mmcblk0boot1: retrying using single block read
    ** 15 printk messages dropped ** [    7.769047] mmcblk0boot1: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.781646] mmcblk0boot1: error -84 transferring data, sector 63, nr 1, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.794372] mmcblk0boot0: error -84 transferring data, sector 120, nr 8, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.806983] mmcblk0boot0: error -84 transferring data, sector 123, nr 5, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.819066] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.831755] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 23 printk messages dropped ** [    7.842638] mmcblk0boot0: retrying using single block read
    ** 16 printk messages dropped ** [    7.851671] mmcblk0boot0: error -84 transferring data, sector 61, nr 3, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.864298] mmcblk0boot1: error -84 transferring data, sector 127, nr 1, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.875772] mmcblk0boot1: retrying using single block read
    ** 18 printk messages dropped ** [    7.881972] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.892885] mmcblk0boot1: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    ** 25 printk messages dropped ** [    7.906077] mmcblk0boot1: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.919273] mmcblk0boot0: error -84 transferring data, sector 127, nr 1, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.930777] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 28 printk messages dropped ** [    7.944954] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    7.957215] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    7.970087] mmcblk0boot1: error -84 transferring data, sector 56, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    7.983366] mmcblk0boot1: error -84 transferring data, sector 123, nr 5, cmd response 0x900, card status 0x0
    ** 22 printk messages dropped ** [    7.994863] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    8.007689] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    8.019354] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    8.033500] mmcblk0boot0: error -84 transferring data, sector 131, nr 5, cmd response 0x900, card status 0x0
    ** 24 printk messages dropped ** [    8.046346] mmcblk0boot0: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    ** 23 printk messages dropped ** [    8.058582] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    ** 22 printk messages dropped ** [    8.069704] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    ** 10 printk messages dropped ** [    8.075243] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    ** 21 printk messages dropped ** [    8.086308] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    ** 26 printk messages dropped ** [    8.100486] mmcblk0boot1: error -84 transferring data, sector 131, nr 5, cmd response 0x900, card status 0x0
    ** 16 printk messages dropped ** [    8.109046] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0xb00
    [    8.109050] mmcblk0boot1: retrying using single block read
    [    8.109723] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0x0
    [    8.110328] mmcblk0boot1: error -84 transferring data, sector 17, nr 7, cmd response 0x900, card status 0x0
    [    8.110932] mmcblk0boot1: error -84 transferring data, sector 18, nr 6, cmd response 0x900, card status 0x0
    [    8.111541] mmcblk0boot1: error -84 transferring data, sector 19, nr 5, cmd response 0x900, card status 0x0
    [    8.112142] mmcblk0boot1: error -84 transferring data, sector 20, nr 4, cmd response 0x900, card status 0x0
    [    8.112741] mmcblk0boot1: error -84 transferring data, sector 21, nr 3, cmd response 0x900, card status 0x0
    [    8.113340] mmcblk0boot1: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    [    8.113935] mmcblk0boot1: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    [    8.114514] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.114567] mmcblk0boot1: error -84 transferring data, sector 128, nr 8, cmd response 0x900, card status 0xb00
    [    8.114571] mmcblk0boot1: retrying using single block read
    [    8.115246] mmcblk0boot1: error -84 transferring data, sector 128, nr 8, cmd response 0x900, card status 0x0
    [    8.115851] mmcblk0boot1: error -84 transferring data, sector 129, nr 7, cmd response 0x900, card status 0x0
    [    8.116455] mmcblk0boot1: error -84 transferring data, sector 130, nr 6, cmd response 0x900, card status 0x0
    [    8.117058] mmcblk0boot1: error -84 transferring data, sector 131, nr 5, cmd response 0x900, card status 0x0
    [    8.117673] mmcblk0boot1: error -84 transferring data, sector 132, nr 4, cmd response 0x900, card status 0x0
    [    8.118270] mmcblk0boot1: error -84 transferring data, sector 133, nr 3, cmd response 0x900, card status 0x0
    [    8.118866] mmcblk0boot1: error -84 transferring data, sector 134, nr 2, cmd response 0x900, card status 0x0
    [    8.119473] mmcblk0boot1: error -84 transferring data, sector 135, nr 1, cmd response 0x900, card status 0x0
    [    8.120041] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.120100] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.120103] mmcblk0boot1: retrying using single block read
    [    8.120785] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.121392] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.122001] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.122603] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.123209] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.123815] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.124412] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.125013] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.125582] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.125644] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.125648] mmcblk0boot1: retrying using single block read
    [    8.126325] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.126937] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.127554] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.128150] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.128754] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.129355] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.129952] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.130550] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.131123] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.131184] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.131188] mmcblk0boot1: retrying using single block read
    [    8.131867] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.132473] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.133079] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.133680] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.134282] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.134882] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.135480] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.136079] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.136647] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.136707] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.136711] mmcblk0boot1: retrying using single block read
    [    8.137396] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.138002] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.138604] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.139210] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.139808] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.140407] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.141006] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.141609] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.142178] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.142236] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.142240] mmcblk0boot1: retrying using single block read
    [    8.142920] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.143525] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.144132] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.144739] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.145344] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.145946] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.146548] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.147149] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.147723] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.147782] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.147786] mmcblk0boot1: retrying using single block read
    [    8.148459] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.149071] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.149675] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.150283] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.150888] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.151488] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.152086] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.152682] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.153859] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.153911] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.153914] mmcblk0boot0: retrying using single block read
    [    8.154589] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.155196] mmcblk0boot0: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.155800] mmcblk0boot0: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.156405] mmcblk0boot0: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.157004] mmcblk0boot0: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.157611] mmcblk0boot0: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.158210] mmcblk0boot0: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.158807] mmcblk0boot0: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.159380] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.159434] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.159438] mmcblk0boot0: retrying using single block read
    [    8.160115] mmcblk0boot0: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.160722] mmcblk0boot0: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.161324] mmcblk0boot0: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.161930] mmcblk0boot0: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.162532] mmcblk0boot0: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.163132] mmcblk0boot0: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.163736] mmcblk0boot0: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.164331] mmcblk0boot0: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.164908] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.164962] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.164965] mmcblk0boot0: retrying using single block read
    [    8.165639] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.166243] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.166849] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.167457] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.168057] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.168660] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.169254] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.169857] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.170428] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.170481] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.170485] mmcblk0boot0: retrying using single block read
    [    8.171159] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.171768] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.172372] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.172975] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.173577] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.174179] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.174774] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.175373] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.175943] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.175999] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.176001] mmcblk0boot0: retrying using single block read
    [    8.176674] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.177279] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.177882] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.178485] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.179089] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.179689] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.180284] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.180882] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.181456] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.181510] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.181513] mmcblk0boot0: retrying using single block read
    [    8.182188] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.182793] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.183395] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.183997] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.184602] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.185204] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.185801] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.186401] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.186972] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.187023] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.187026] mmcblk0boot0: retrying using single block read
    [    8.187713] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.188310] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.188913] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.189516] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.190118] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.190717] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.191313] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.191911] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.192484] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.192537] mmcblk0boot0: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0xb00
    [    8.192541] mmcblk0boot0: retrying using single block read
    [    8.193221] mmcblk0boot0: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0x0
    [    8.193827] mmcblk0boot0: error -84 transferring data, sector 17, nr 7, cmd response 0x900, card status 0x0
    [    8.194431] mmcblk0boot0: error -84 transferring data, sector 18, nr 6, cmd response 0x900, card status 0x0
    [    8.195035] mmcblk0boot0: error -84 transferring data, sector 19, nr 5, cmd response 0x900, card status 0x0
    [    8.195634] mmcblk0boot0: error -84 transferring data, sector 20, nr 4, cmd response 0x900, card status 0x0
    [    8.196236] mmcblk0boot0: error -84 transferring data, sector 21, nr 3, cmd response 0x900, card status 0x0
    [    8.196838] mmcblk0boot0: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    [    8.197436] mmcblk0boot0: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    [    8.198006] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.198060] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.198063] mmcblk0boot0: retrying using single block read
    [    8.198736] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.199342] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.199946] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.200550] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.201151] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.201749] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.202347] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.202946] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.203519] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.203573] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.203576] mmcblk0boot0: retrying using single block read
    [    8.204248] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.204854] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.205455] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.206062] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.206660] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.207264] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.208832] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.209251] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.209807] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.209867] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.209870] mmcblk0boot0: retrying using single block read
    [    8.210550] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.211157] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.211758] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.212361] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.212958] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.213563] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.214165] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.214759] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.215941] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.215998] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.216001] mmcblk0boot1: retrying using single block read
    [    8.216681] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.217290] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.217904] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.218498] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.219100] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.219703] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.220304] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.220902] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.221477] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.221533] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.221537] mmcblk0boot1: retrying using single block read
    [    8.222212] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.222823] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.223427] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.224035] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.224635] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.225234] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.225835] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.226431] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.227005] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.227062] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0xb00
    [    8.227065] mmcblk0boot1: retrying using single block read
    [    8.227741] mmcblk0boot1: error -84 transferring data, sector 64, nr 8, cmd response 0x900, card status 0x0
    [    8.228346] mmcblk0boot1: error -84 transferring data, sector 65, nr 7, cmd response 0x900, card status 0x0
    [    8.228951] mmcblk0boot1: error -84 transferring data, sector 66, nr 6, cmd response 0x900, card status 0x0
    [    8.229553] mmcblk0boot1: error -84 transferring data, sector 67, nr 5, cmd response 0x900, card status 0x0
    [    8.230160] mmcblk0boot1: error -84 transferring data, sector 68, nr 4, cmd response 0x900, card status 0x0
    [    8.230760] mmcblk0boot1: error -84 transferring data, sector 69, nr 3, cmd response 0x900, card status 0x0
    [    8.231357] mmcblk0boot1: error -84 transferring data, sector 70, nr 2, cmd response 0x900, card status 0x0
    [    8.231955] mmcblk0boot1: error -84 transferring data, sector 71, nr 1, cmd response 0x900, card status 0x0
    [    8.232527] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.232580] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.232583] mmcblk0boot1: retrying using single block read
    [    8.233258] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.233862] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.234468] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.235071] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.235669] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.236269] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.236867] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.237481] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.238039] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.238093] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.238097] mmcblk0boot1: retrying using single block read
    [    8.238770] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.239380] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.239981] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.240589] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.241187] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.241790] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.242391] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.242986] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.243558] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.243612] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.243615] mmcblk0boot1: retrying using single block read
    [    8.244292] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.244899] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.245505] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.246106] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.246705] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.247302] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.247907] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.248501] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.249074] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.249129] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.249131] mmcblk0boot1: retrying using single block read
    [    8.249804] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.250410] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.251016] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.251618] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.252220] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.252816] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.253412] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.254010] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.254585] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.254639] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.254642] mmcblk0boot1: retrying using single block read
    [    8.255315] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.255919] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.256528] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.257133] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.257741] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.258338] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.258934] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.259533] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.260106] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.260159] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0xb00
    [    8.260163] mmcblk0boot1: retrying using single block read
    [    8.260836] mmcblk0boot1: error -84 transferring data, sector 16, nr 8, cmd response 0x900, card status 0x0
    [    8.261446] mmcblk0boot1: error -84 transferring data, sector 17, nr 7, cmd response 0x900, card status 0x0
    [    8.262055] mmcblk0boot1: error -84 transferring data, sector 18, nr 6, cmd response 0x900, card status 0x0
    [    8.262659] mmcblk0boot1: error -84 transferring data, sector 19, nr 5, cmd response 0x900, card status 0x0
    [    8.263261] mmcblk0boot1: error -84 transferring data, sector 20, nr 4, cmd response 0x900, card status 0x0
    [    8.263862] mmcblk0boot1: error -84 transferring data, sector 21, nr 3, cmd response 0x900, card status 0x0
    [    8.264461] mmcblk0boot1: error -84 transferring data, sector 22, nr 2, cmd response 0x900, card status 0x0
    [    8.265058] mmcblk0boot1: error -84 transferring data, sector 23, nr 1, cmd response 0x900, card status 0x0
    [    8.265631] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.265684] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.265687] mmcblk0boot1: retrying using single block read
    [    8.266360] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.266965] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.267569] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.268172] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.268768] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.269370] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.269966] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.270561] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.271134] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.271189] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.271192] mmcblk0boot1: retrying using single block read
    [    8.271864] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.272468] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.273073] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.273675] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.274273] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.274876] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.275473] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.276075] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.277254] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.277310] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.277313] mmcblk0boot0: retrying using single block read
    [    8.277990] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.278597] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.279203] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.279808] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.280404] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.281009] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.281608] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.282203] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.282775] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.282829] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.282832] mmcblk0boot0: retrying using single block read
    [    8.283509] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.284115] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.284717] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.285317] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.285918] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.286518] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.287112] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.287714] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.288281] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.288336] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.288340] mmcblk0boot0: retrying using single block read
    [    8.289015] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.289620] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.290223] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.290826] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.291425] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.292026] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.292625] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.293220] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.293797] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.293851] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.293854] mmcblk0boot0: retrying using single block read
    [    8.294526] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.295131] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.295735] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.296343] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.296943] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.297561] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.298150] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.298750] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.299316] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.299375] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.299378] mmcblk0boot0: retrying using single block read
    [    8.300056] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.300666] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.301272] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.301874] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.302477] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.303075] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.303673] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.304267] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.304835] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.304896] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.304900] mmcblk0boot0: retrying using single block read
    [    8.305579] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.306185] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.306786] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.307397] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.307993] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.308590] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.309188] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.309783] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.310355] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.310416] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.310419] mmcblk0boot0: retrying using single block read
    [    8.311095] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.311703] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.312305] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.312909] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.313507] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.314111] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.314707] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.315308] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.315874] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.315932] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.315935] mmcblk0boot0: retrying using single block read
    [    8.316614] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.317222] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.317836] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.318431] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.319032] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.319633] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.320235] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.320834] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.321400] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.321457] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.321460] mmcblk0boot0: retrying using single block read
    [    8.322142] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.322751] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.323352] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.323953] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.324556] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.325152] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.325750] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.326346] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.326915] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.326975] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.326978] mmcblk0boot0: retrying using single block read
    [    8.327662] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.328262] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.328866] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.329465] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.330063] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.330662] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.331264] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.331860] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.332430] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.332490] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.332494] mmcblk0boot0: retrying using single block read
    [    8.333172] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.333776] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.334381] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.334986] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.335591] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.336189] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.336789] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.337391] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.338563] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.338615] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.338618] mmcblk0boot1: retrying using single block read
    [    8.339292] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.339902] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.340508] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.341108] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.341713] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.342314] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.342909] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.343505] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.344083] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.344137] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.344140] mmcblk0boot1: retrying using single block read
    [    8.344811] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.345416] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.346020] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.346621] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.347225] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.347829] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.348422] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.349018] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.349592] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.349645] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.349648] mmcblk0boot1: retrying using single block read
    [    8.350320] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.350927] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.351528] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.352129] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.352734] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.353336] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.353932] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.354530] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.355105] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.355159] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.355162] mmcblk0boot1: retrying using single block read
    [    8.355834] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.356443] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.357046] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.357665] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.358260] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.358861] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.359462] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.360058] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.360626] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.360685] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.360688] mmcblk0boot1: retrying using single block read
    [    8.361370] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.361979] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.362581] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.363184] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.363785] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.364381] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.364979] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.365576] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.366143] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.366201] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.366204] mmcblk0boot1: retrying using single block read
    [    8.366883] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.367492] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.368084] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.368687] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.369285] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.369885] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.370481] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.371081] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.371653] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.371707] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.371710] mmcblk0boot1: retrying using single block read
    [    8.372382] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.372988] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.373590] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.374195] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.374793] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.375397] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.375999] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.376592] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.377167] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.377220] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.377224] mmcblk0boot1: retrying using single block read
    [    8.377900] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.378508] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.379111] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.379717] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.380317] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.380916] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.381512] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.382107] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.382684] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.382738] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.382741] mmcblk0boot1: retrying using single block read
    [    8.383413] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.384019] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.384623] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.385223] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.385823] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.386420] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.387020] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.387629] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.388189] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.388248] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.388252] mmcblk0boot1: retrying using single block read
    [    8.388930] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.389534] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.390140] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.390740] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.391339] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.391942] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.392538] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.393140] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.393710] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.393769] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.393772] mmcblk0boot1: retrying using single block read
    [    8.394455] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.395060] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.395664] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.396268] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.396873] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.397483] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.398066] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.398662] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.399837] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.399890] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.399894] mmcblk0boot0: retrying using single block read
    [    8.400570] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.401174] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.401778] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.402378] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.402978] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.403579] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.404175] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.404771] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.405343] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.405397] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.405401] mmcblk0boot0: retrying using single block read
    [    8.406072] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.406679] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.407277] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.407885] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.408483] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.409084] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.409682] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.410279] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.410854] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.410908] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.410911] mmcblk0boot0: retrying using single block read
    [    8.411580] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.412193] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.412794] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.413400] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.414003] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.414603] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.415206] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.415799] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.416373] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.416429] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.416431] mmcblk0boot0: retrying using single block read
    [    8.417106] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.417727] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.418323] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.418926] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.419525] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.420125] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.420721] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.421320] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.421883] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.421941] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.421945] mmcblk0boot0: retrying using single block read
    [    8.422622] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.423228] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.423832] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.424431] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.425031] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.425633] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.426227] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.426825] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.427402] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.427462] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.427465] mmcblk0boot0: retrying using single block read
    [    8.428145] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.428748] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.429351] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.429958] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.430554] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.431159] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.431753] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.432356] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.432927] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.432984] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.432987] mmcblk0boot0: retrying using single block read
    [    8.433670] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.434275] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.434879] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.435485] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.436090] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.436692] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.437288] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.437890] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.438453] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.438508] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.438511] mmcblk0boot0: retrying using single block read
    [    8.439185] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.439794] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.440398] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.440997] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.441599] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.442197] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.442793] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.443390] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.443962] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.444016] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.444019] mmcblk0boot0: retrying using single block read
    [    8.444692] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.445300] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.445904] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.446505] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.447106] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.447708] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.448302] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.448903] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.449475] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.449528] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.449531] mmcblk0boot0: retrying using single block read
    [    8.450204] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.450815] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.451418] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.452024] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.452626] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.453227] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.453825] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.454427] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.454987] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.455040] mmcblk0boot0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    8.455044] mmcblk0boot0: retrying using single block read
    [    8.455709] mmcblk0boot0: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    [    8.456305] mmcblk0boot0: error -84 transferring data, sector 9, nr 7, cmd response 0x900, card status 0x0
    [    8.456893] mmcblk0boot0: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    [    8.457500] mmcblk0boot0: error -84 transferring data, sector 11, nr 5, cmd response 0x900, card status 0x0
    [    8.458073] mmcblk0boot0: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    [    8.458661] mmcblk0boot0: error -84 transferring data, sector 13, nr 3, cmd response 0x900, card status 0x0
    [    8.459244] mmcblk0boot0: error -84 transferring data, sector 14, nr 2, cmd response 0x900, card status 0x0
    [    8.459827] mmcblk0boot0: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    [    8.461008] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.461060] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.461064] mmcblk0boot1: retrying using single block read
    [    8.461736] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.462343] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.462947] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.463558] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.464154] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.464758] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.465356] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.465954] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.466528] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.466584] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.466588] mmcblk0boot1: retrying using single block read
    [    8.467262] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.467873] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.468479] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.469081] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.469684] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.470284] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.470879] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.471473] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.472052] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.472104] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.472107] mmcblk0boot1: retrying using single block read
    [    8.472781] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.473385] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.473990] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.474590] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.475196] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.475796] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.476392] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.476985] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.477567] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.477630] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.477633] mmcblk0boot1: retrying using single block read
    [    8.478308] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.478912] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.479515] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.480117] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.480717] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.481321] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.481916] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.482517] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.483089] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.483142] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.483145] mmcblk0boot1: retrying using single block read
    [    8.483819] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.484425] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.485034] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.485636] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.486239] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.486840] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.487442] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.488036] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.488610] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.488663] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.488666] mmcblk0boot1: retrying using single block read
    [    8.489342] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.489952] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.490554] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.491156] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.491755] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.492353] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.492951] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.493547] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.494120] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.494174] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.494177] mmcblk0boot1: retrying using single block read
    [    8.494850] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.495454] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.496056] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.496658] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.497256] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.497873] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.498461] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.499061] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.499628] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.499686] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.499690] mmcblk0boot1: retrying using single block read
    [    8.500367] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.500972] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.501575] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.502180] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.502787] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.503383] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.503983] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.504580] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.505153] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.505214] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.505217] mmcblk0boot1: retrying using single block read
    [    8.505899] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.506507] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.507110] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.507726] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.508318] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.508920] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.509516] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.510115] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.510682] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.510740] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.510744] mmcblk0boot1: retrying using single block read
    [    8.511428] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.512031] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.512633] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.513234] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.513834] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.514433] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.515029] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.515628] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.516196] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.516253] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.516256] mmcblk0boot1: retrying using single block read
    [    8.516937] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.517552] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.518140] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.518743] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.519340] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.519939] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.520544] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.521139] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.522316] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.522368] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.522371] mmcblk0boot0: retrying using single block read
    [    8.523043] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.523651] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.524259] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.524863] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.525465] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.526064] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.526664] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.527260] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.527831] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.527885] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.527888] mmcblk0boot0: retrying using single block read
    [    8.528564] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.529174] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.529779] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.530380] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.530979] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.531577] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.532175] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.532771] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.533342] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.533396] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.533399] mmcblk0boot0: retrying using single block read
    [    8.534074] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.534682] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.535283] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.535884] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.536485] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.537086] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.537681] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.538284] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.538854] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.538903] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.538906] mmcblk0boot0: retrying using single block read
    [    8.539574] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.540181] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.540786] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.541394] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.541993] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.542597] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.543197] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.543794] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.544365] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.544418] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.544421] mmcblk0boot0: retrying using single block read
    [    8.545098] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.545704] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.546309] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.546916] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.547529] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.548119] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.548715] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.549309] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.549883] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.549943] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.549947] mmcblk0boot0: retrying using single block read
    [    8.550622] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.551229] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.551833] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.552433] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.553057] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.553628] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.554225] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.554819] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.555396] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.555450] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.555453] mmcblk0boot0: retrying using single block read
    [    8.556127] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.556731] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.557349] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.557936] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.558534] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.559138] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.559735] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.560335] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.560910] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.560963] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.560966] mmcblk0boot0: retrying using single block read
    [    8.561643] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.562247] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.562853] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.563454] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.564060] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.564664] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.565258] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.565857] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.566427] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.566482] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.566484] mmcblk0boot0: retrying using single block read
    [    8.567157] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.567768] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.568368] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.568971] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.569571] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.570174] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.570768] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.571365] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.571937] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.571990] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.571993] mmcblk0boot0: retrying using single block read
    [    8.572664] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.573275] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.573877] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.574477] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.575081] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.575679] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.576274] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.576875] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.577437] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.577489] mmcblk0boot0: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0xb00
    [    8.577493] mmcblk0boot0: retrying using single block read
    [    8.578157] mmcblk0boot0: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0x0
    [    8.578753] mmcblk0boot0: error -84 transferring data, sector 25, nr 7, cmd response 0x900, card status 0x0
    [    8.579345] mmcblk0boot0: error -84 transferring data, sector 26, nr 6, cmd response 0x900, card status 0x0
    [    8.579940] mmcblk0boot0: error -84 transferring data, sector 27, nr 5, cmd response 0x900, card status 0x0
    [    8.580531] mmcblk0boot0: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    [    8.581120] mmcblk0boot0: error -84 transferring data, sector 29, nr 3, cmd response 0x900, card status 0x0
    [    8.581708] mmcblk0boot0: error -84 transferring data, sector 30, nr 2, cmd response 0x900, card status 0x0
    [    8.582296] mmcblk0boot0: error -84 transferring data, sector 31, nr 1, cmd response 0x900, card status 0x0
    [    8.583458] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.583510] mmcblk0boot1: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0xb00
    [    8.583513] mmcblk0boot1: retrying using single block read
    [    8.584179] mmcblk0boot1: error -84 transferring data, sector 8, nr 8, cmd response 0x900, card status 0x0
    [    8.584772] mmcblk0boot1: error -84 transferring data, sector 9, nr 7, cmd response 0x900, card status 0x0
    [    8.585361] mmcblk0boot1: error -84 transferring data, sector 10, nr 6, cmd response 0x900, card status 0x0
    [    8.585951] mmcblk0boot1: error -84 transferring data, sector 11, nr 5, cmd response 0x900, card status 0x0
    [    8.586538] mmcblk0boot1: error -84 transferring data, sector 12, nr 4, cmd response 0x900, card status 0x0
    [    8.587128] mmcblk0boot1: error -84 transferring data, sector 13, nr 3, cmd response 0x900, card status 0x0
    [    8.587717] mmcblk0boot1: error -84 transferring data, sector 14, nr 2, cmd response 0x900, card status 0x0
    [    8.588301] mmcblk0boot1: error -84 transferring data, sector 15, nr 1, cmd response 0x900, card status 0x0
    [    8.588873] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.588927] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.588931] mmcblk0boot1: retrying using single block read
    [    8.589605] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.590214] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.590821] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.591422] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.592021] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.592622] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.593218] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.593819] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.594390] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.594443] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.594446] mmcblk0boot1: retrying using single block read
    [    8.595119] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.595724] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.596330] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.596932] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.597533] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.598134] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.598729] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.599331] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.599905] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.599958] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.599961] mmcblk0boot1: retrying using single block read
    [    8.600635] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.601241] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.601842] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.602445] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.603049] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.603648] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.604248] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.604847] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.605420] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.605473] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.605477] mmcblk0boot1: retrying using single block read
    [    8.606149] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.606761] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.607390] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.607980] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.608576] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.609174] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.609772] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.610369] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.610936] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.610997] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.611000] mmcblk0boot1: retrying using single block read
    [    8.611682] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.612286] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.612889] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.613490] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.614089] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.614689] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.615286] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.615882] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.616451] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.616511] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.616515] mmcblk0boot1: retrying using single block read
    [    8.617196] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.617805] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.618402] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.619003] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.619604] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.620202] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.620802] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.621399] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.621969] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.622028] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.622031] mmcblk0boot1: retrying using single block read
    [    8.622709] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.623318] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.623920] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.624527] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.625126] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.625731] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.626332] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.626927] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.627499] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.627560] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.627563] mmcblk0boot1: retrying using single block read
    [    8.628245] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.628852] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.629457] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.630063] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.630663] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.631260] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.631858] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.632454] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.633026] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.633086] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.633089] mmcblk0boot1: retrying using single block read
    [    8.633768] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.634375] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.634978] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.635578] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.636179] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.636777] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.637378] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.637964] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.638539] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.638593] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.638596] mmcblk0boot1: retrying using single block read
    [    8.639267] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.639873] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.640480] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.641081] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.641680] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.642284] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.642878] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.643478] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.644657] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.644710] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.644714] mmcblk0boot0: retrying using single block read
    [    8.645389] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.645995] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.646599] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.647205] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.647810] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.648407] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.649004] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.649598] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.650172] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.650226] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.650229] mmcblk0boot0: retrying using single block read
    [    8.650903] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.651511] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.652113] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.652715] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.653316] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.653913] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.654508] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.655109] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.655678] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.655730] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.655733] mmcblk0boot0: retrying using single block read
    [    8.656404] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.657012] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.657615] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.658217] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.658815] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.659414] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.660018] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.660613] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.661190] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.661244] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.661247] mmcblk0boot0: retrying using single block read
    [    8.661920] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.662530] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.663132] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.663737] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.664337] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.664941] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.665540] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.666137] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.666708] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.666760] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.666763] mmcblk0boot0: retrying using single block read
    [    8.667455] mmcblk0boot0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.668050] mmcblk0boot0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.668657] mmcblk0boot0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.669259] mmcblk0boot0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.669861] mmcblk0boot0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.670458] mmcblk0boot0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.671059] mmcblk0boot0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.671655] mmcblk0boot0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.681707] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.681759] mmcblk0boot1: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0xb00
    [    8.681763] mmcblk0boot1: retrying using single block read
    [    8.682429] mmcblk0boot1: error -84 transferring data, sector 24, nr 8, cmd response 0x900, card status 0x0
    [    8.683022] mmcblk0boot1: error -84 transferring data, sector 25, nr 7, cmd response 0x900, card status 0x0
    [    8.683619] mmcblk0boot1: error -84 transferring data, sector 26, nr 6, cmd response 0x900, card status 0x0
    [    8.684213] mmcblk0boot1: error -84 transferring data, sector 27, nr 5, cmd response 0x900, card status 0x0
    [    8.684802] mmcblk0boot1: error -84 transferring data, sector 28, nr 4, cmd response 0x900, card status 0x0
    [    8.685391] mmcblk0boot1: error -84 transferring data, sector 29, nr 3, cmd response 0x900, card status 0x0
    [    8.685980] mmcblk0boot1: error -84 transferring data, sector 30, nr 2, cmd response 0x900, card status 0x0
    [    8.686566] mmcblk0boot1: error -84 transferring data, sector 31, nr 1, cmd response 0x900, card status 0x0
    [    8.687140] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.687194] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.687197] mmcblk0boot1: retrying using single block read
    [    8.687876] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.688477] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.689079] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.689682] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.690282] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.690882] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.691480] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.692079] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.692653] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.692707] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.692710] mmcblk0boot1: retrying using single block read
    [    8.693381] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.693987] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.694592] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.695199] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.695798] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.696403] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.696998] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.697600] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.698171] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.698225] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.698228] mmcblk0boot1: retrying using single block read
    [    8.698899] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.699512] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.700117] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.700719] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.701318] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.701917] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.702514] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.703112] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.703683] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.703736] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.703739] mmcblk0boot1: retrying using single block read
    [    8.704411] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.705016] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.705620] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.706222] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.706820] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.708853] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.709261] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.709857] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [    8.710432] omap_hsmmc 4809c000.mmc: ADMA err: ST_TFR, desc at 0xfd441008 follows the erroneous one
    [    8.710485] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
    [    8.710488] mmcblk0boot1: retrying using single block read
    [    8.711160] mmcblk0boot1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
    [    8.711765] mmcblk0boot1: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
    [    8.712367] mmcblk0boot1: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
    [    8.712974] mmcblk0boot1: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
    [    8.713572] mmcblk0boot1: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
    [    8.714178] mmcblk0boot1: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
    [    8.714772] mmcblk0boot1: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
    [    8.715373] mmcblk0boot1: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
    [   17.497366] ata1: softreset failed (1st FIS failed)
    udevd[404]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    udevd[413]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    
    udevd[417]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    udevd[444]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
    
    [   27.507359] ata1: softreset failed (1st FIS failed)
    [   27.857363] ata1: SATA link down (SStatus 0 SControl 300)
    [   27.896671] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
    Starting Bootlog daemon: bootlogd.
    ALSA: Restoring mixer settings...
    No state is present for card DRA7xxEVMMCASP1
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP1
    No state is present for card DRA7xxEVMMCASP2
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP2
    No state is present for card DRA7xxEVMMCASP3
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP3
    No state is present for card DRA7xxEVMMCASP4
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP4
    No state is present for card DRA7xxEVMMCASP8
    Found hardware: "DRA7xx-EVM-MCAS" "" "" "" ""
    Hardware is initialized using a generic method
    No state is present for card DRA7xxEVMMCASP8
    Thu Sep  3 18:41:00 UTC 2015
    
    
    
    2017.11.23 15:00
    
    
    
    This version is for J6
    
    
    
    ****** This application only support ASCII code 0 to 127 ******
    
    
    
    ****** This application only support CB version #F ******
    [   43.416085] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   43.422627] usb usb4: USB disconnect, device number 1
    [   43.430892] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
    [   43.436608] xhci-hcd xhci-hcd.1.auto: remove, state 4
    [   43.441755] usb usb3: USB disconnect, device number 1
    [   43.449122] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
    [   43.455756] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   43.460880] usb usb2: USB disconnect, device number 1
    [   43.468127] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
    [   43.473839] xhci-hcd xhci-hcd.0.auto: remove, state 4
    [   43.479011] usb usb1: USB disconnect, device number 1
    [   43.486322] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
    [   43.597557] usbcore: deregistering device driver usb
    [   43.604204] usbcore: deregistering interface driver usbfs
    [   43.611324] usbcore: deregistering interface driver hub
    [AB_server.c, make_sure_usb_kernel_stack_removed, 374] temp: drwxr-xr-x   27 root     root             0 Jan  1  1970 .
    dr-xr-xr-x   12 root     root             0 Jan  1  1970 ..
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ac97
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clockevents
    drwxr-xr-x    4 root     root             0 Jan  1  1970 clocksource
    drwxr-xr-x    4 root     root             0 Jan  1  1970 container
    drwxr-xr-x    4 root     root             0 Jan  1  1970 cpu
    drwxr-xr-x    4 root     root             0 Jan  1  1970 edac
    drwxr-xr-x    4 root     root             0 Jan  1  1970 event_source
    drwxr-xr-x    4 root     root             0 Jan  1  1970 hid
    drwxr-xr-x    4 root     root             0 Jan  1  1970 i2c
    drwxr-xr-x    4 root     root             0 Jan  1  1970 iio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mdio_bus
    drwxr-xr-x    4 root     root             0 Jan  1  1970 media
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mipi-dsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 mmc
    drwxr-xr-x    5 root     root             0 Jan  1  1970 pci
    drwxr-xr-x    4 root     root             0 Jan  1  1970 platform
    drwxr-xr-x    4 root     root             0 Jan  1  1970 rpmsg
    drwxr-xr-x    4 root     root             0 Jan  1  1970 scsi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 sdio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 serio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 soc
    drwxr-xr-x    4 root     root             0 Jan  1  1970 spi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 ulpi
    drwxr-xr-x    4 root     root             0 Jan  1  1970 virtio
    drwxr-xr-x    4 root     root             0 Jan  1  1970 workqueue
    
    [AB_server.c, AB_boot_finish, 181] AB boot success, pull high GPIO
    [AB_server.c, AB_boot_finish, 187] AB boot success, pull high GPIO finished
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    /usr/local/bin/set_unused_gpio_input: line 14: echo: write error: Device or resource busy
    /usr/local/bin/set_unused_gpio_input: line 15: /sys/class/gpio/gpio161/direction: No such file or directory
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (0) Bytes
    
    
    INIT: Entering runlevel: 5
    Configuring network interfaces... [   45.373449] net eth0: initializing cpsw version 1.15 (0)
    [   45.379130] net eth0: initialized cpsw ale version 1.4
    [   45.384293] net eth0: ALE Table size 1024
    [   45.391355] libphy: PHY 48485000.mdio:02 not found
    [   45.396173] net eth0: phy "48485000.mdio:02" not found on slave 0, err -19
    [   45.410785] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    /bin/sh: udhcpc: command not found
    done.
    Starting system message bus: dbus.
    [AB_server.c, get_CB_hardware_version, 212] Wait for CB send HW version
    
    
    [AB_server.c, get_CB_hardware_version, 216] Read CB HW version (4) Bytes
    
    
    _version[0]: 30
    _version[1]: 31
    _version[2]: 31
    _version[3]: 30
    _version[4]: 0
    _version[5]: 0
    _version[6]: 0
    _version[7]: 0
    _version[8]: 0
    _version[9]: 0
    _version[10]: 0
    _version[11]: 0
    _version[12]: 0
    _version[13]: 0
    _version[14]: 0
    _version[15]: 0
    [AB_server.c, main, 517] AB_server: get CB's HW version 0110
    
    
    [AB_server.c, get_CB_hardware_version_finish, 254] AB get CB hw version finish, gpio pull low
    [AB_server.c, send_AB_model_info_to_CB, 279] write AB model info total (6) Bytes, model: (DRA74X
    )
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    [AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 0
     ______
    [AB_server.c, sync_CB_status, 317] ______ AB GPIO 109 LOW, AB booting ______
    UIM SYSFS Node Not Found
    Starting telnet daemon.
    Starting tiipclad daemon
    GateMP support enabled on host
    
    Opened log file: lad.txt
    
    numProcessors = 5 id = 0 baseId = 0
    
    Spawned daemon: /usr/bin/lad_dra7xx
    
    .
    Starting rpcbind daemon...[AB_server.c, sync_CB_status, 308] ______ AB GPIO 109 status: 1
     ______
    [AB_server.c, sync_CB_status, 312] ______ AB GPIO 109 1, can go ______
    done.
    creating NFS state directory: done
    starting statd: done
    NFS daemon support not enabled in kernel
    Starting syslogd/klogd: done
    Starting thttpd.
    Enabling thermal zones...
    Stopping Bootlog daemon: bootlogd.
    
    root@wnc-j6:~# [AB_server.c, main, 550] ulpi on/off : J6, ULPI test on
    cat /sys/kernel/debug/mmc0/ios
    clock:          52000000 Hz
    vdd:            21 (3.3 ~ 3.4 V)
    bus mode:       2 (push-pull)
    chip select:    0 (don't care)
    power mode:     2 (on)
    bus width:      2 (4 bits)
    timing spec:    1 (mmc high-speed)
    signal voltage: 0 (3.30 V)
    driver type:    0 (driver type B)
    root@wnc-j6:~# lsblk
    NAME         MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
    mmcblk0boot0 179:16   0  128K  1 disk
    mmcblk0boot1 179:32   0  128K  1 disk
    mmcblk1boot0 179:64   0  128K  1 disk
    mmcblk1boot1 179:80   0  128K  1 disk
    mmcblk0      179:0    0  7.3G  0 disk
    mmcblk1      179:48   0  7.3G  0 disk
    |-mmcblk1p1  179:49   0   64M  0 part
    `-mmcblk1p2  179:50   0  7.2G  0 part /
    mmcblk2      179:96   0  3.7G  0 disk
    |-mmcblk2p1  179:97   0   62M  0 part
    `-mmcblk2p2  179:98   0  3.6G  0 part
    root@wnc-j6:~#

    谢谢

    吉布斯

      

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    Hi Gibbs、

    1.  * DRA746 eMMC1接口引导带 eMMC 闪存,包括 TS3A27518、VDD 3.3V、IO 3.3V ? 请确认?  请以下方登录?

    [Kevin ]此内核是 最新的 SDK 版本(6.00.00.03)和 VDD 3.3V、IO 未知、引导卡住在"Waiting for root device PARTUUUUUUEF=bddb4f41-02..."

    2.  * DRA746 eMMC1接口引导带 eMMC 闪存,包括 TS3A27518, VDD 1.8V, IO 1.8V? 请确认?  请以下方登录?

    [Kevin ]是、VDD 1.8V、IO 1.8V。 DTS 如下:

    /*
     * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
     *
     * This program is free software; you can redistribute it and/or modify
     * it under the terms of the GNU General Public License version 2 as
     * published by the Free Software Foundation.
     */
    /dts-v1/;
    
    #include "dra74x.dtsi"
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/clk/ti-dra7-atl.h>
    #include <dt-bindings/input/input.h>
    #include <dt-bindings/pinmux/mux_dra7xx.h>
    
    / {
    	model = "TI DRA746 KC 20230317 12:48";
    	compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7";
    
    	version = "30003-20161032";
    
    	memory {
    		device_type = "memory";
    		reg = <0x0 0x80000000 0x0 0x80000000>; /* 2048 MB */
    //		reg = <0x0 0x80000000 0x0 0x60000000>; /* 1536 MB */
    	};
    
    	reserved_mem: reserved-memory {
    		#address-cells = <2>;
    		#size-cells = <2>;
    		ranges;
    
    		ipu2_cma_pool: ipu2_cma@95800000 {
    			compatible = "shared-dma-pool";
    			reg = <0x0 0x95800000 0x0 0x3800000>;
    			reusable;
    			status = "okay";
    		};
    
    		dsp1_cma_pool: dsp1_cma@99000000 {
    			compatible = "shared-dma-pool";
    			reg = <0x0 0x99000000 0x0 0x4000000>;
    			reusable;
    			status = "okay";
    		};
    
    		ipu1_cma_pool: ipu1_cma@9d000000 {
    			compatible = "shared-dma-pool";
    			reg = <0x0 0x9d000000 0x0 0x2000000>;
    			reusable;
    			status = "okay";
    		};
    
    		dsp2_cma_pool: dsp2_cma@9f000000 {
    			compatible = "shared-dma-pool";
    			reg = <0x0 0x9f000000 0x0 0x800000>;
    			reusable;
    			status = "okay";
    		};
    	};
    #if 0
    	aliases {
    		display0 = &hdmi0;
    		display1 = &fpd_disp;
    		//sound0 = &snd0;
    		sound1 = &hdmi;
    		//i2c7 = &disp_ser;
    	};
    #endif
    	evm_3v3_sd: fixedregulator-sd {
    		compatible = "regulator-fixed";
    		regulator-name = "evm_3v3_sd";
    		regulator-min-microvolt = <3300000>;
    		regulator-max-microvolt = <3300000>;
    		regulator-always-on;
    		regulator-boot-on;
    	};
    
    	evm_1v8_sd: fixedregulator-sd {
    		compatible = "regulator-fixed";
    		regulator-name = "evm_1v8_sd";
    		regulator-min-microvolt = <1800000>;
    		regulator-max-microvolt = <1800000>;
    		regulator-always-on;
    		regulator-boot-on;
    	};
    
    	evm_3v3_sw: fixedregulator-evm_3v3_sw {
    		compatible = "regulator-fixed";
    		regulator-name = "evm_3v3_sw";
    		vin-supply = <&sysen1>;
    		regulator-min-microvolt = <3300000>;
    		regulator-max-microvolt = <3300000>;
    	};
    
    	aic_dvdd: fixedregulator-aic_dvdd {
    		/* TPS77018DBVT */
    		compatible = "regulator-fixed";
    		regulator-name = "aic_dvdd";
    		vin-supply = <&evm_3v3_sw>;
    		regulator-min-microvolt = <1800000>;
    		regulator-max-microvolt = <1800000>;
    	};
    
    	vmmcwl_fixed: fixedregulator-mmcwl {
    		compatible = "regulator-fixed";
    		regulator-name = "vmmcwl_fixed";
    		regulator-min-microvolt = <1800000>;
    		regulator-max-microvolt = <1800000>;
    		//gpio = <&gpio5 8 0>;	/* gpio5_8 */
    		startup-delay-us = <70000>;
    		regulator-always-on;
    		regulator-boot-on;
    	};
    #if 0
    	extcon_usb1: extcon_usb1 {
    		compatible = "linux,extcon-usb-gpio";
    		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
    	};
    
    	extcon_usb2: extcon_usb2 {
    		compatible = "linux,extcon-usb-gpio";
    		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
    	};
    #endif
    	vtt_fixed: fixedregulator-vtt {
    		compatible = "regulator-fixed";
    		regulator-name = "vtt_fixed";
    		regulator-min-microvolt = <1350000>;
    		regulator-max-microvolt = <1350000>;
    		regulator-always-on;
    		regulator-boot-on;
    		enable-active-high;
    		vin-supply = <&sysen2>;
    		//gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
    	};
    
    	btsco_mcasp1: btsco_mcasp1@0 {
    		#sound-dai-cells = <0>;
    		compatible = "delta,dfbmcs320-mcasp1";
    		status = "okay";
    	};
    
    	btsco_mcasp2: btsco_mcasp2@0 {
    		#sound-dai-cells = <0>;
    		compatible = "delta,dfbmcs320-mcasp2";
    		status = "okay";
    	};
    
    	btsco_mcasp3: btsco_mcasp3@0 {
    		#sound-dai-cells = <0>;
    		compatible = "delta,dfbmcs320-mcasp3";
    		status = "okay";
    	};
    
    	btsco_mcasp4: btsco_mcasp4@0 {
    		#sound-dai-cells = <0>;
    		compatible = "delta,dfbmcs320-mcasp4";
    		status = "okay";
    	};
    
    	btsco_mcasp8: btsco_mcasp8@0 {
    		#sound-dai-cells = <0>;
    		compatible = "delta,dfbmcs320-mcasp8";
    		status = "okay";
    	};
    
    	snd1: sound@1 {
    		compatible = "simple-audio-card-mcasp1";
    		simple-audio-card,name = "DRA7xx-EVM-MCASP1";
    #if 0
    		/* we do not have codec */
    		simple-audio-card,mclk-fs = <256>;
    #endif
    		simple-audio-card,widgets =
    			"Headphone", "Headphone Jack",
    			"Line", "Line Out",
    			"Microphone", "Mic Jack",
    			"Line", "Line In";
    		simple-audio-card,routing =
    			"Headphone Jack",       "HPLOUT",
    			"Headphone Jack",       "HPROUT",
    			"Line Out",		"LLOUT",
    			"Line Out",		"RLOUT",
    			"MIC3L",		"Mic Jack",
    			"MIC3R",		"Mic Jack",
    			"Mic Jack",		"Mic Bias",
    			"LINE1L",               "Line In",
    			"LINE1R",               "Line In";
    		status = "okay";
    
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&btsco_codec1>;
    			frame-master = <&btsco_codec1>;
    			bitclock-inversion;
    
    			cpu {
    				sound-dai = <&mcasp1>;
    				system-clock-frequency = <8192000>;
    			};
    
    			btsco_codec1: codec {
    				sound-dai = <&btsco_mcasp1>;
    			};
    		};
    	};
    
    	snd2: sound@2 {
    		compatible = "simple-audio-card-mcasp2";
    		simple-audio-card,name = "DRA7xx-EVM-MCASP2";
    #if 0
    		/* we do not have codec */
    		simple-audio-card,mclk-fs = <256>;
    #endif
    		simple-audio-card,widgets =
    			"Headphone", "Headphone Jack",
    			"Line", "Line Out",
    			"Microphone", "Mic Jack",
    			"Line", "Line In";
    		simple-audio-card,routing =
    			"Headphone Jack",       "HPLOUT",
    			"Headphone Jack",       "HPROUT",
    			"Line Out",		"LLOUT",
    			"Line Out",		"RLOUT",
    			"MIC3L",		"Mic Jack",
    			"MIC3R",		"Mic Jack",
    			"Mic Jack",		"Mic Bias",
    			"LINE1L",               "Line In",
    			"LINE1R",               "Line In";
    		status = "okay";
    
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&btsco_codec2>;
    			frame-master = <&btsco_codec2>;
    			bitclock-inversion;
    
    			cpu {
    				sound-dai = <&mcasp2>;
    				system-clock-frequency = <8192000>;
    			};
    
    			btsco_codec2: codec {
    				sound-dai = <&btsco_mcasp2>;
    			};
    		};
    	};
    
    	snd3: sound@3 {
    		compatible = "simple-audio-card-mcasp3";
    		simple-audio-card,name = "DRA7xx-EVM-MCASP3";
    #if 0
    		/* we do not have codec */
    		simple-audio-card,mclk-fs = <256>;
    #endif
    		simple-audio-card,widgets =
    			"Headphone", "Headphone Jack",
    			"Line", "Line Out",
    			"Microphone", "Mic Jack",
    			"Line", "Line In";
    		simple-audio-card,routing =
    			"Headphone Jack",       "HPLOUT",
    			"Headphone Jack",       "HPROUT",
    			"Line Out",		"LLOUT",
    			"Line Out",		"RLOUT",
    			"MIC3L",		"Mic Jack",
    			"MIC3R",		"Mic Jack",
    			"Mic Jack",		"Mic Bias",
    			"LINE1L",               "Line In",
    			"LINE1R",               "Line In";
    		status = "okay";
    
    #if 0
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&sound3_master>;
    			frame-master = <&sound3_master>;
    			bitclock-inversion;
    
    			sound3_master: cpu {
    				sound-dai = <&mcasp3>;
    				system-clock-frequency = <8192000>;
    			};
    
    			codec {
    				sound-dai = <&btsco_mcasp3>;
    			};
    		};
    #else
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&btsco_codec3>;
    			frame-master = <&btsco_codec3>;
    			bitclock-inversion;
    
    			cpu {
    				sound-dai = <&mcasp3>;
    				system-clock-frequency = <8192000>;
    			};
    
    			btsco_codec3: codec {
    				sound-dai = <&btsco_mcasp3>;
    			};
    		};
    #endif
    	};
    
    	snd4: sound@4 {
    		compatible = "simple-audio-card-mcasp4";
    		simple-audio-card,name = "DRA7xx-EVM-MCASP4";
    #if 0
    		/* we do not have codec */
    		simple-audio-card,mclk-fs = <256>;
    #endif
    		simple-audio-card,widgets =
    			"Headphone", "Headphone Jack",
    			"Line", "Line Out",
    			"Microphone", "Mic Jack",
    			"Line", "Line In";
    		simple-audio-card,routing =
    			"Headphone Jack",       "HPLOUT",
    			"Headphone Jack",       "HPROUT",
    			"Line Out",		"LLOUT",
    			"Line Out",		"RLOUT",
    			"MIC3L",		"Mic Jack",
    			"MIC3R",		"Mic Jack",
    			"Mic Jack",		"Mic Bias",
    			"LINE1L",               "Line In",
    			"LINE1R",               "Line In";
    		status = "okay";
    
    #if 0
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&sound4_master>;
    			frame-master = <&sound4_master>;
    			bitclock-inversion;
    
    			sound4_master: cpu {
    				sound-dai = <&mcasp4>;
    				system-clock-frequency = <8192000>;
    			};
    
    			codec {
    				sound-dai = <&btsco_mcasp4>;
    			};
    		};
    #else
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&btsco_codec4>;
    			frame-master = <&btsco_codec4>;
    			bitclock-inversion;
    
    			cpu {
    				sound-dai = <&mcasp4>;
    				system-clock-frequency = <8192000>;
    			};
    
    			btsco_codec4: codec {
    				sound-dai = <&btsco_mcasp4>;
    			};
    		};
    #endif
    	};
    
    	snd8: sound@8 {
    		compatible = "simple-audio-card-mcasp8";
    		simple-audio-card,name = "DRA7xx-EVM-MCASP8";
    #if 0
    		/* we do not have codec */
    		simple-audio-card,mclk-fs = <256>;
    #endif
    		simple-audio-card,widgets =
    			"Headphone", "Headphone Jack",
    			"Line", "Line Out",
    			"Microphone", "Mic Jack",
    			"Line", "Line In";
    		simple-audio-card,routing =
    			"Headphone Jack",       "HPLOUT",
    			"Headphone Jack",       "HPROUT",
    			"Line Out",		"LLOUT",
    			"Line Out",		"RLOUT",
    			"MIC3L",		"Mic Jack",
    			"MIC3R",		"Mic Jack",
    			"Mic Jack",		"Mic Bias",
    			"LINE1L",               "Line In",
    			"LINE1R",               "Line In";
    		status = "okay";
    
    		simple-audio-card,dai-link@0 {
    			format = "i2s";
    			bitclock-master = <&sound8_master>;
    			frame-master = <&sound8_master>;
    			bitclock-inversion;
    
    			sound8_master: cpu {
    				sound-dai = <&mcasp8>;
    				system-clock-frequency = <8192000>;
    			};
    
    			codec {
    				sound-dai = <&btsco_mcasp8>;
    			};
    		};
    	};
    
    	hdmi0: connector@1 {
    		status = "disabled";
    		compatible = "hdmi-connector";
    		label = "hdmi";
    
    		type = "a";
    
    		port {
    			hdmi_connector_in: endpoint {
    				remote-endpoint = <&tpd12s015_out>;
    			};
    		};
    	};
    
    	tpd12s015: encoder@1 {
    		compatible = "ti,dra7evm-tpd12s015";
    		status = "disabled";
    
    		pinctrl-names = "i2c", "ddc";
    		pinctrl-0 = <&hdmi_i2c_sel_pin &hdmi_i2c_pins_i2c>;
    		pinctrl-1 = <&hdmi_i2c_sel_pin &hdmi_i2c_pins_ddc>;
    
    		ddc-i2c-bus = <&i2c2>;
    		mcasp-gpio = <&mcasp8>;
    
    		gpios = <&pcf_hdmi 4 0>,	/* P4, CT CP HPD */
    			<&pcf_hdmi 5 0>,	/* P5, LS OE */
    			<&gpio7 12 0>;	/* gpio7_12/sp1_cs2, HPD */
    
    		ports {
    			#address-cells = <1>;
    			#size-cells = <0>;
    
    			port@0 {
    				reg = <0>;
    
    				tpd12s015_in: endpoint@0 {
    					remote-endpoint = <&hdmi_out>;
    				};
    			};
    
    			port@1 {
    				reg = <1>;
    
    				tpd12s015_out: endpoint@0 {
    					remote-endpoint = <&hdmi_connector_in>;
    				};
    			};
    		};
    	};
    };
    
    &dra7_iodelay_core {
            mmc1_iodelay_ddr50_conf: mmc1_iodelay_ddr50_conf {
                    pinctrl-single,pins = <
                            0x618 (A_DELAY(572) | G_DELAY(540))     /* CFG_MMC1_CLK_IN */
                            0x624 (A_DELAY(0) | G_DELAY(600))       /* CFG_MMC1_CMD_IN */
                            0x630 (A_DELAY(403) | G_DELAY(120))     /* CFG_MMC1_DAT0_IN */
                            0x63c (A_DELAY(23) | G_DELAY(60))       /* CFG_MMC1_DAT1_IN */
                            0x648 (A_DELAY(25) | G_DELAY(60))       /* CFG_MMC1_DAT2_IN */
                            0x654 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT3_IN */
                            0x620 (A_DELAY(1525) | G_DELAY(0))      /* CFG_MMC1_CLK_IN */
                            0x628 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_CMD_OEN */
                            0x62c (A_DELAY(55) | G_DELAY(0))        /* CFG_MMC1_CMD_OUT */
                            0x634 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT0_OEN */
                            0x638 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT0_OUT */
                            0x640 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT1_OEN */
                            0x644 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT1_OUT */
                            0x64c (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT2_OEN */
                            0x650 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT2_OUT */
                            0x658 (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT3_OEN */
                            0x65c (A_DELAY(0) | G_DELAY(0))         /* CFG_MMC1_DAT3_OUT */
                    >;
            };
            mmc2_iodelay_ddr_3_3v_conf: mmc2_iodelay_ddr_3_3v_conf {
                    pinctrl-single,pins = <
                            0x18c (A_DELAY(0) | G_DELAY(120))       /* CFG_GPMC_A19_IN */
                            0x1a4 (A_DELAY(265) | G_DELAY(360))     /* CFG_GPMC_A20_IN */
                            0x1b0 (A_DELAY(0) | G_DELAY(120))       /* CFG_GPMC_A21_IN */
                            0x1bc (A_DELAY(0) | G_DELAY(120))       /* CFG_GPMC_A22_IN */
                            0x1c8 (A_DELAY(287) | G_DELAY(420))     /* CFG_GPMC_A23_IN */
                            0x1d4 (A_DELAY(144) | G_DELAY(240))     /* CFG_GPMC_A24_IN */
                            0x1e0 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A25_IN */
                            0x1ec (A_DELAY(0) | G_DELAY(120))       /* CFG_GPMC_A26_IN */
                            0x1f8 (A_DELAY(120) | G_DELAY(180))     /* CFG_GPMC_A27_IN */
                            0x360 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_CS1_IN */
                            0x190 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A19_OEN */
                            0x194 (A_DELAY(174) | G_DELAY(0))       /* CFG_GPMC_A19_OUT */
                            0x1a8 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A20_OEN */
                            0x1ac (A_DELAY(168) | G_DELAY(0))       /* CFG_GPMC_A20_OUT */
                            0x1b4 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A21_OEN */
                            0x1b8 (A_DELAY(136) | G_DELAY(0))       /* CFG_GPMC_A21_OUT */
                            0x1c0 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A22_OEN */
                            0x1c4 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A22_OUT */
                            0x1d0 (A_DELAY(879) | G_DELAY(0))       /* CFG_GPMC_A23_OUT */
                            0x1d8 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A24_OEN */
                            0x1dc (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A24_OUT */
                            0x1e4 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A25_OEN */
                            0x1e8 (A_DELAY(34) | G_DELAY(0))        /* CFG_GPMC_A25_OUT */
                            0x1f0 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A26_OEN */
                            0x1f4 (A_DELAY(120) | G_DELAY(0))       /* CFG_GPMC_A26_OUT */
                            0x1fc (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A27_OEN */
                            0x200 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A27_OUT */
                            0x364 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_CS1_OEN */
                            0x368 (A_DELAY(11) | G_DELAY(0))        /* CFG_GPMC_CS1_OUT */
                    >;
            };
    };
    
    &dra7_pmx_core {
    	// Audio
    	mcasp1_pins: mcasp1_pins {
    		pinctrl-single,pins = <
    			/* all data PINs have to set output due to clk PINs mux (aclk"r", fs"r") in CB */
    
    			/* clk slave */
    			0x2a8 (PIN_INPUT           | MUX_MODE0)		/* D14, mcasp1_fsx,  mode 0 */
    			0x2cc (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* C12, mcasp1_axr6, mode 0, rx */
    			0x2d0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* D12, mcasp1_axr7, mode 0, tx */
    			0x2c4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* E12, mcasp1_axr4, mode 0, rx*/
    			/* clk slave */
    			0x2a4 (PIN_INPUT           | MUX_MODE0)		/* C14, mcasp1_aclkx, mode 0  */
    			0x2c8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* F13, mcasp1_axr5, mode 0, tx  */
    			0x2c0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* J11, mcasp1_axr3, mode 0, tx */
    		>;
    	};
    
    	mcasp2_pins: mcasp2_pins {
    		pinctrl-single,pins = <
    			/* all data PINs have to set input due to clk PINs mux (aclk"r", fs"r") in AB */
    
    			/* clk slave */
    			0x300 (PIN_INPUT           | MUX_MODE0)		/* A20, mcasp2_fsr, mode 0 */
    			0x304 (PIN_INPUT           | MUX_MODE0)		/* B15, mcasp2_axr0, mode 0, DT_FM1, tx */
    			0x310 (PIN_INPUT           | MUX_MODE0)		/* A16, mcasp2_axr3, mode 0, DT_FM3, rx */
    			0x30c (PIN_INPUT           | MUX_MODE0)		/* C15, mcasp2_axr2, mode 0, DT_FM3, tx */
    			/* clk slave */
    			0x2fc (PIN_INPUT           | MUX_MODE0)		/* E15, mcasp2_aclkr, mode 0 */
    			0x308 (PIN_INPUT           | MUX_MODE0)		/* A15, mcasp2_axr1, mode 0, DT_FM1, rx */
    		>;
    	};
    
    	mcasp3_pins: mcasp3_pins {
    		pinctrl-single,pins = <
    			0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* B19, mcasp3_axr0, mode 0, tx */
    			/* clk slave */
    			0x324 (PIN_INPUT           | MUX_MODE0)		/* B18, mcasp3_aclkx, mode 0 */
    			0x330 (PIN_INPUT           | MUX_MODE0)		/* C17, mcasp3_axr1, mode 0, rx */
    			/* clk slave */
    			0x328 (PIN_INPUT           | MUX_MODE0)		/* F15, mcasp3_fsx, mode 0 */
    		>;
    	};
    
    	mcasp4_pins: mcasp4_pins {
    		pinctrl-single,pins = <
    			/* clk slave */
    			0x334 (PIN_INPUT           | MUX_MODE0)		/* C18, mcasp4_aclkx, mode 0,  */
    			/* clk slave */
    			0x338 (PIN_INPUT           | MUX_MODE0)		/* A21, mcasp4_fsx, mode 0,  */
    			0x33C (PIN_INPUT           | MUX_MODE0)		/* G16, mcasp4_axr0, mode 0, rx */
    		>;
    	};
    
    	mcasp8_pins: mcasp8_pins {
    		pinctrl-single,pins = <
    			/* clk master */
    			0x320 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)		/* A17, mcasp8_fsx, mode 1 */
    			/* clk master */
    			0x31c (PIN_OUTPUT_PULLDOWN | MUX_MODE1)		/* B17, mcasp8_aclkx, mode 1 */
    			0x314 (PIN_INPUT           | MUX_MODE1)		/* D15, mcasp8_axr0, mode 1, rx */
    			0x318 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)		/* B16, mcasp8_axr1, mode 1, tx */
    		>;
    	};
    
    	// ULPI
    	usb3_pins: pinmux_usb3_pins {
    		pinctrl-single,pins = <
    			0x3a0 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat7.usb3_ulpi_clk  GPIO1_25 AB5
    			0x39c (PIN_OUTPUT | MUX_MODE3)			// mmc3_dat6.usb3_ulpi_stp  GPIO1_24 AB8
    			0x398 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat5.usb3_ulpi_dir  GPIO1_23 AD6
    			0x394 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat4.usb3_ulpi_nxt  GPIO1_22 AC8
    			
    			0x390 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat3.usb3_ulpi_d0  GPIO7_2 AC3
    			0x38c (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat2.usb3_ulpi_d1  GPIO7_1 AC9
    			0x388 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat1.usb3_ulpi_d2  GPIO7_0 AC6
    			0x384 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_dat0.usb3_ulpi_d3  GPIO6_31 AC7
    			0x380 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_cmd.usb3_ulpi_d4  GPIO6_30 AC4
    			0x37c (PIN_INPUT_PULLDOWN | MUX_MODE3)	// mmc3_clk.usb3_ulpi_d5  GPIO6_29 AD4
    			0x378 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// gpio6_11.usb3_ulpi_d6  GPIO6_11 AB4
    			0x374 (PIN_INPUT_PULLDOWN | MUX_MODE3)	// gpio6_10.usb3_ulpi_d7  GPIO6_10 AC5
    		>;
    	};
    
    	uart1_pins: pinmux_uart1_pins {
    		pinctrl-single,pins = <
    			/* mcasp1 test with Carrier Board */
    			/* clk slave */
    			0x2a8 (PIN_INPUT           | MUX_MODE0)		/* D14, mcasp1_fsx,  mode 0 */
    			0x2cc (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* C12, mcasp1_axr6, mode 0, rx */
    			0x2d0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* D12, mcasp1_axr7, mode 0, tx */
    			0x2c4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* E12, mcasp1_axr4, mode 0, rx*/
    			/* clk slave */
    			0x2a4 (PIN_INPUT           | MUX_MODE0)		/* C14, mcasp1_aclkx, mode 0  */
    			0x2c8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* F13, mcasp1_axr5, mode 0, tx  */
    			0x2c0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* J11, mcasp1_axr3, mode 0, tx */
    
    			/* mcasp2 test with Carrier Board */
    			/* clk slave */
    			0x300 (PIN_INPUT           | MUX_MODE0)		/* A20, mcasp2_fsr, mode 0 */
    			0x304 (PIN_INPUT           | MUX_MODE0)		/* B15, mcasp2_axr0, mode 0, DT_FM1, tx */
    			0x310 (PIN_INPUT           | MUX_MODE0)		/* A16, mcasp2_axr3, mode 0, DT_FM3, rx */
    			0x30c (PIN_INPUT           | MUX_MODE0)		/* C15, mcasp2_axr2, mode 0, DT_FM3, tx */
    			/* clk slave */
    			0x2fc (PIN_INPUT           | MUX_MODE0)		/* E15, mcasp2_aclkr, mode 0 */
    			0x308 (PIN_INPUT           | MUX_MODE0)		/* A15, mcasp2_axr1, mode 0, DT_FM1, rx */
    
    			/* mcasp3 test with Carrier Board */
    			0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* B19, mcasp3_axr0, mode 0, tx */
    			/* clk slave */
    			0x324 (PIN_INPUT           | MUX_MODE0)		/* B18, mcasp3_aclkx, mode 0 */
    			0x330 (PIN_INPUT           | MUX_MODE0)		/* C17, mcasp3_axr1, mode 0, rx */
    			/* clk slave */
    			0x328 (PIN_INPUT           | MUX_MODE0)		/* F15, mcasp3_fsx, mode 0 */
    
    			/* mcasp4 test with Carrier Board */
    			/* clk slave */
    			0x334 (PIN_INPUT           | MUX_MODE0)		/* C18, mcasp4_aclkx, mode 0,  */
    			/* clk slave */
    			0x338 (PIN_INPUT           | MUX_MODE0)		/* A21, mcasp4_fsx, mode 0,  */
    			0x33C (PIN_INPUT           | MUX_MODE0)		/* G16, mcasp4_axr0, mode 0, rx */
    
    			/* mcasp8 test with Carrier Board */
    			/* clk master */
    			0x320 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)		/* A17, mcasp8_fsx, mode 1 */
    			/* clk master */
    			0x31c (PIN_OUTPUT_PULLDOWN | MUX_MODE1)		/* B17, mcasp8_aclkx, mode 1 */
    			0x314 (PIN_INPUT           | MUX_MODE1)		/* D15, mcasp8_axr0, mode 1, rx */
    			0x318 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)		/* B16, mcasp8_axr1, mode 1, tx */
    
    			// i2c_3		
    			GPMC_ADVN_ALE (PIN_INPUT | MUX_MODE8)	/* gpmc_advn_ale.i2c3_sda -> 8 */
    			GPMC_CLK      (PIN_INPUT | MUX_MODE8)	/* gpmc_clk.i2c3_scl -> 8 */		
    			// i2c_4	
    			MMC1_SDCD (PIN_INPUT | MUX_MODE4)  		/* mmc1_sdcd.i2c4_sda -> 4 */
    			MMC1_SDWP (PIN_INPUT | MUX_MODE4)  		/* mmc1_sdwp.i2c4_scl -> 4 */		
    			// i2c_5	
    			MCASP1_AXR0 (PIN_INPUT | MUX_MODE10)	/* mcasp1_axr0.i2c5_sda -> 10 */
    			MCASP1_AXR1 (PIN_INPUT | MUX_MODE10)	/* mcasp1_axr1.i2c5_scl -> 10 */	
    	
    			// spi 1.0, 1.1, 1.3
    			SPI1_SCLK	(PIN_INPUT | MUX_MODE0)	/*	0x3A4	*/
    			SPI1_D1		(PIN_INPUT | MUX_MODE0)	/*	0x3A8	*/
    			SPI1_D0		(PIN_INPUT | MUX_MODE0)	/*	0x3AC	*/
    			SPI1_CS0	(PIN_INPUT | MUX_MODE0)	/*	0x3B0	*/
    			SPI1_CS1	(PIN_INPUT | MUX_MODE0)	/*	0x3B4	*/
    			SPI1_CS3	(PIN_INPUT | MUX_MODE0)	/*	0x3BC	*/
    	
    			// spi 2.0
    			SPI2_SCLK	( PIN_INPUT | MUX_MODE0 )	/*	0x3C0	*/
    			SPI2_D1		( PIN_INPUT | MUX_MODE0 )	/*	0x3C4	*/
    			SPI2_D0		( PIN_INPUT | MUX_MODE0 )	/*	0x3C8	*/
    			SPI2_CS0	( PIN_INPUT | MUX_MODE0 )	/*	0x3CC	*/
    
    			// spi 3.0
    			VOUT1_CLK		(PIN_INPUT | MUX_MODE8)	// DAB_SPI_CS		GPIO4_19
    			VOUT1_DE		(PIN_INPUT | MUX_MODE8)	// DAB_SPI_MISO	GPIO4_20
    			VOUT1_HSYNC	(PIN_INPUT | MUX_MODE8)	// DAB_SPI_MOSI	GPIO4_22
    			VOUT1_VSYNC	(PIN_INPUT | MUX_MODE8)	// DAB_SPI_SCK		GPIO4_23	
    			
    			// BT656 vin4b
    			MDIO_MCLK	(PIN_INPUT | MUX_MODE5)		/*	0x23C	*/	// BT656_CLK1
    			MDIO_D	(PIN_INPUT | MUX_MODE5)		/*	0x240	*/		// BT656_DO
    			UART3_RXD	(PIN_INPUT | MUX_MODE5)	/*	0x248	*/		// BT656_D1
    			UART3_TXD	(PIN_INPUT | MUX_MODE5)	/*	0x24C	*/		// BT656_D2
    			RGMII0_TXC	(PIN_INPUT | MUX_MODE5)	/*	0x250	*/	// BT656_D3
    			RGMII0_TXCTL	(PIN_INPUT | MUX_MODE5)	/*	0x254	*/	// BT656_D4
    			RGMII0_RXC	(PIN_INPUT | MUX_MODE5)	/*	0x268	*/		// BT656_D5
    			RGMII0_RXCTL	(PIN_INPUT | MUX_MODE5)	/*	0x26C	*/	// BT656_D6	
    			RGMII0_RXD3	(PIN_INPUT | MUX_MODE5)	/*	0x270	*/		// BT656_D7
    
    			RGMII0_RXD2	(PIN_INPUT | MUX_MODE14)	/*	0x274	*/
    			VIN2A_DE0	(PIN_INPUT | MUX_MODE14)	/*	0x158	*/
    
    //===================================================================================
    
    		//GPMC_AD0	(PIN_INPUT | MUX_MODE14)	/*	0x000	*/
    		//GPMC_AD1	(PIN_INPUT | MUX_MODE14)	/*	0x004	*/
    		//GPMC_AD2	(PIN_INPUT | MUX_MODE14)	/*	0x008	*/
    		//GPMC_AD3	(PIN_INPUT | MUX_MODE14)	/*	0x00C	*/
    		//GPMC_AD4	(PIN_INPUT | MUX_MODE14)	/*	0x010	*/
    		//GPMC_AD5	(PIN_INPUT | MUX_MODE14)	/*	0x014	*/
    		//GPMC_AD6	(PIN_INPUT | MUX_MODE14)	/*	0x018	*/
    		//GPMC_AD7	(PIN_INPUT | MUX_MODE14)	/*	0x01C	*/
    		//GPMC_AD8	(PIN_INPUT | MUX_MODE14)	/*	0x020	*/
    		//GPMC_AD9	(PIN_INPUT | MUX_MODE14)	/*	0x024	*/
    		//GPMC_AD10	(PIN_INPUT | MUX_MODE14)	/*	0x028	*/
    		//GPMC_AD11	(PIN_INPUT | MUX_MODE14)	/*	0x02C	*/
    		//GPMC_AD12	(PIN_INPUT | MUX_MODE14)	/*	0x030	*/
    		//GPMC_AD13	(PIN_INPUT | MUX_MODE14)	/*	0x034	*/
    		//GPMC_AD14	(PIN_INPUT | MUX_MODE14)	/*	0x038	*/
    		//GPMC_AD15	(PIN_INPUT | MUX_MODE14)	/*	0x03C	*/
    		//GPMC_A0	(PIN_INPUT | MUX_MODE14)	/*	0x040	*/
    		//GPMC_A1	(PIN_INPUT | MUX_MODE14)	/*	0x044	*/
    		//GPMC_A2	(PIN_INPUT | MUX_MODE14)	/*	0x048	*/
    		//GPMC_A3	(PIN_INPUT | MUX_MODE14)	/*	0x04C	*/
    		//GPMC_A4	(PIN_INPUT | MUX_MODE14)	/*	0x050	*/
    		//GPMC_A5	(PIN_INPUT | MUX_MODE14)	/*	0x054	*/
    		//GPMC_A6	(PIN_INPUT | MUX_MODE14)	/*	0x058	*/
    		//GPMC_A7	(PIN_INPUT | MUX_MODE14)	/*	0x05C	*/
    		//GPMC_A8	(PIN_INPUT | MUX_MODE14)	/*	0x060	*/
    		//GPMC_A9	(PIN_INPUT | MUX_MODE14)	/*	0x064	*/
    		//GPMC_A10	(PIN_INPUT | MUX_MODE14)	/*	0x068	*/
    		//GPMC_A11	(PIN_INPUT | MUX_MODE14)	/*	0x06C	*/
    		GPMC_A12	(PIN_INPUT | MUX_MODE14)	/*	0x070	*/
    		GPMC_A13	(PIN_INPUT | MUX_MODE14)	/*	0x074	*/
    		GPMC_A14	(PIN_INPUT | MUX_MODE14)	/*	0x078	*/
    		GPMC_A15	(PIN_INPUT | MUX_MODE14)	/*	0x07C	*/
    		GPMC_A16	(PIN_INPUT | MUX_MODE14)	/*	0x080	*/
    		GPMC_A17	(PIN_INPUT | MUX_MODE14)	/*	0x084	*/
    		GPMC_A18	(PIN_INPUT | MUX_MODE14)	/*	0x088	*/
    		//GPMC_A19	(PIN_INPUT | MUX_MODE14)	/*	0x08C	*/
    		//GPMC_A20	(PIN_INPUT | MUX_MODE14)	/*	0x090	*/
    		//GPMC_A21	(PIN_INPUT | MUX_MODE14)	/*	0x094	*/
    		//GPMC_A22	(PIN_INPUT | MUX_MODE14)	/*	0x098	*/
    		//GPMC_A23	(PIN_INPUT | MUX_MODE14)	/*	0x09C	*/
    		//GPMC_A24	(PIN_INPUT | MUX_MODE14)	/*	0x0A0	*/
    		//GPMC_A25	(PIN_INPUT | MUX_MODE14)	/*	0x0A4	*/
    		//GPMC_A26	(PIN_INPUT | MUX_MODE14)	/*	0x0A8	*/
    		//GPMC_A27	(PIN_INPUT | MUX_MODE14)	/*	0x0AC	*/
    		//GPMC_CS1	(PIN_INPUT | MUX_MODE14)	/*	0x0B0	*/
    		GPMC_CS0	(PIN_INPUT | MUX_MODE14)	/*	0x0B4	*/
    		GPMC_CS2	(PIN_INPUT | MUX_MODE14)	/*	0x0B8	*/
    		//GPMC_CS3	(PIN_INPUT | MUX_MODE14)	/*	0x0BC	*/
    		//GPMC_CLK	(PIN_INPUT | MUX_MODE14)	/*	0x0C0	*/
    		//GPMC_ADVN_ALE	(PIN_INPUT | MUX_MODE14)	/*	0x0C4	*/
    		GPMC_OEN_REN	(PIN_INPUT | MUX_MODE14)	/*	0x0C8	*/
    		GPMC_WEN	(PIN_INPUT | MUX_MODE14)	/*	0x0CC	*/
    		GPMC_BEN0	(PIN_INPUT | MUX_MODE14)	/*	0x0D0	*/
    		GPMC_BEN1	(PIN_INPUT | MUX_MODE14)	/*	0x0D4	*/
    		GPMC_WAIT0	(PIN_INPUT | MUX_MODE14)	/*	0x0D8	*/
    		VIN1A_CLK0	(PIN_INPUT | MUX_MODE14)	/*	0x0DC	*/
    		VIN1B_CLK1	(PIN_INPUT | MUX_MODE14)	/*	0x0E0	*/
    		VIN1A_DE0	(PIN_INPUT | MUX_MODE14)	/*	0x0E4	*/
    		VIN1A_FLD0	(PIN_INPUT | MUX_MODE14)	/*	0x0E8	*/
    		VIN1A_HSYNC0	(PIN_INPUT | MUX_MODE14)	/*	0x0EC	*/
    		VIN1A_VSYNC0	(PIN_INPUT | MUX_MODE14)	/*	0x0F0	*/
    		VIN1A_D0	(PIN_INPUT | MUX_MODE14)	/*	0x0F4	*/
    		VIN1A_D1	(PIN_INPUT | MUX_MODE14)	/*	0x0F8	*/
    		VIN1A_D2	(PIN_INPUT | MUX_MODE14)	/*	0x0FC	*/
    		VIN1A_D3	(PIN_INPUT | MUX_MODE14)	/*	0x100	*/
    		VIN1A_D4	(PIN_INPUT | MUX_MODE14)	/*	0x104	*/
    		VIN1A_D5	(PIN_INPUT | MUX_MODE14)	/*	0x108	*/
    		VIN1A_D6	(PIN_INPUT | MUX_MODE14)	/*	0x10C	*/
    		VIN1A_D7	(PIN_INPUT | MUX_MODE14)	/*	0x110	*/
    		VIN1A_D8	(PIN_INPUT | MUX_MODE14)	/*	0x114	*/
    		VIN1A_D9	(PIN_INPUT | MUX_MODE14)	/*	0x118	*/
    		VIN1A_D10	(PIN_INPUT | MUX_MODE14)	/*	0x11C	*/
    		VIN1A_D11	(PIN_INPUT | MUX_MODE14)	/*	0x120	*/
    		VIN1A_D12	(PIN_INPUT | MUX_MODE14)	/*	0x124	*/
    		VIN1A_D13	(PIN_INPUT | MUX_MODE14)	/*	0x128	*/
    		VIN1A_D14	(PIN_INPUT | MUX_MODE14)	/*	0x12C	*/
    		VIN1A_D15	(PIN_INPUT | MUX_MODE14)	/*	0x130	*/
    		VIN1A_D16	(PIN_INPUT | MUX_MODE14)	/*	0x134	*/
    		VIN1A_D17	(PIN_INPUT | MUX_MODE14)	/*	0x138	*/
    		VIN1A_D18	(PIN_INPUT | MUX_MODE14)	/*	0x13C	*/
    		VIN1A_D19	(PIN_INPUT | MUX_MODE14)	/*	0x140	*/
    		VIN1A_D20	(PIN_INPUT | MUX_MODE14)	/*	0x144	*/
    		VIN1A_D21	(PIN_INPUT | MUX_MODE14)	/*	0x148	*/
    		VIN1A_D22	(PIN_INPUT | MUX_MODE14)	/*	0x14C	*/
    		VIN1A_D23	(PIN_INPUT | MUX_MODE14)	/*	0x150	*/
    		VIN2A_CLK0	(PIN_INPUT | MUX_MODE14)	/*	0x154	*/
    //		VIN2A_DE0	(PIN_INPUT | MUX_MODE14)	/*	0x158	*/
    		VIN2A_FLD0	(PIN_INPUT | MUX_MODE14)	/*	0x15C	*/
    		VIN2A_HSYNC0	(PIN_INPUT | MUX_MODE14)	/*	0x160	*/
    		VIN2A_VSYNC0	(PIN_INPUT | MUX_MODE14)	/*	0x164	*/
    		VIN2A_D0	(PIN_INPUT | MUX_MODE14)	/*	0x168	*/
    		VIN2A_D1	(PIN_INPUT | MUX_MODE14)	/*	0x16C	*/
    		//VIN2A_D2	(PIN_INPUT | MUX_MODE14)	/*	0x170	*/
    		//VIN2A_D3	(PIN_INPUT | MUX_MODE14)	/*	0x174	*/
    		VIN2A_D4	(PIN_INPUT | MUX_MODE14)	/*	0x178	*/
    		VIN2A_D5	(PIN_INPUT | MUX_MODE14)	/*	0x17C	*/
    		VIN2A_D6	(PIN_INPUT | MUX_MODE14)	/*	0x180	*/
    		VIN2A_D7	(PIN_INPUT | MUX_MODE14)	/*	0x184	*/
    		//VIN2A_D8	(PIN_INPUT | MUX_MODE14)	/*	0x188	*/
    		//VIN2A_D9	(PIN_INPUT | MUX_MODE14)	/*	0x18C	*/
    		VIN2A_D10	(PIN_INPUT | MUX_MODE14)	/*	0x190	*/
    		VIN2A_D11	(PIN_INPUT | MUX_MODE14)	/*	0x194	*/
    		VIN2A_D12	(PIN_INPUT | MUX_MODE14)	/*	0x198	*/
    		VIN2A_D13	(PIN_INPUT | MUX_MODE14)	/*	0x19C	*/
    		VIN2A_D14	(PIN_INPUT | MUX_MODE14)	/*	0x1A0	*/
    		VIN2A_D15	(PIN_INPUT | MUX_MODE14)	/*	0x1A4	*/
    		VIN2A_D16	(PIN_INPUT | MUX_MODE14)	/*	0x1A8	*/
    		VIN2A_D17	(PIN_INPUT | MUX_MODE14)	/*	0x1AC	*/
    		VIN2A_D18	(PIN_INPUT | MUX_MODE14)	/*	0x1B0	*/
    		VIN2A_D19	(PIN_INPUT | MUX_MODE14)	/*	0x1B4	*/
    		VIN2A_D20	(PIN_INPUT | MUX_MODE14)	/*	0x1B8	*/
    		VIN2A_D21	(PIN_INPUT | MUX_MODE14)	/*	0x1BC	*/
    		VIN2A_D22	(PIN_INPUT | MUX_MODE14)	/*	0x1C0	*/
    		VIN2A_D23	(PIN_INPUT | MUX_MODE14)	/*	0x1C4	*/
    		//VOUT1_CLK	(PIN_INPUT | MUX_MODE14)	/*	0x1C8	*/
    		//VOUT1_DE	(PIN_INPUT | MUX_MODE14)	/*	0x1CC	*/
    		VOUT1_FLD	(PIN_INPUT | MUX_MODE14)	/*	0x1D0	*/
    		//VOUT1_HSYNC	(PIN_INPUT | MUX_MODE14)	/*	0x1D4	*/
    		//VOUT1_VSYNC	(PIN_INPUT | MUX_MODE14)	/*	0x1D8	*/
    		//VOUT1_D0	(PIN_INPUT | MUX_MODE14)	/*	0x1DC	*/	// uart5
    		//VOUT1_D1	(PIN_INPUT | MUX_MODE14)	/*	0x1E0	*/	// uart5
    		VOUT1_D2	(PIN_INPUT | MUX_MODE14)	/*	0x1E4	*/
    		VOUT1_D3	(PIN_INPUT | MUX_MODE14)	/*	0x1E8	*/
    		VOUT1_D4	(PIN_INPUT | MUX_MODE14)	/*	0x1EC	*/
    		VOUT1_D5	(PIN_INPUT | MUX_MODE14)	/*	0x1F0	*/
    		VOUT1_D6	(PIN_INPUT | MUX_MODE14)	/*	0x1F4	*/
    		VOUT1_D7	(PIN_INPUT | MUX_MODE14)	/*	0x1F8	*/
    		//VOUT1_D8	(PIN_INPUT | MUX_MODE14)	/*	0x1FC	*/	// uart6
    		//VOUT1_D9	(PIN_INPUT | MUX_MODE14)	/*	0x200	*/	// uart6
    		VOUT1_D10	(PIN_INPUT | MUX_MODE14)	/*	0x204	*/
    		VOUT1_D11	(PIN_INPUT | MUX_MODE14)	/*	0x208	*/
    		VOUT1_D12	(PIN_INPUT | MUX_MODE14)	/*	0x20C	*/
    		VOUT1_D13	(PIN_INPUT | MUX_MODE14)	/*	0x210	*/
    		VOUT1_D14	(PIN_INPUT | MUX_MODE14)	/*	0x214	*/
    		VOUT1_D15	(PIN_INPUT | MUX_MODE14)	/*	0x218	*/
    		VOUT1_D16	(PIN_INPUT | MUX_MODE14)	/*	0x21C	*/
    		VOUT1_D17	(PIN_INPUT | MUX_MODE14)	/*	0x220	*/
    		VOUT1_D18	(PIN_INPUT | MUX_MODE14)	/*	0x224	*/
    		VOUT1_D19	(PIN_INPUT | MUX_MODE14)	/*	0x228	*/
    		VOUT1_D20	(PIN_INPUT | MUX_MODE14)	/*	0x22C	*/
    		VOUT1_D21	(PIN_INPUT | MUX_MODE14)	/*	0x230	*/
    		VOUT1_D22	(PIN_INPUT | MUX_MODE14)	/*	0x234	*/
    		VOUT1_D23	(PIN_INPUT | MUX_MODE14)	/*	0x238	*/
    //		MDIO_MCLK	(PIN_INPUT | MUX_MODE14)	/*	0x23C	*/
    //		MDIO_D	(PIN_INPUT | MUX_MODE14)	/*	0x240	*/
    		RMII_MHZ_50_CLK	(PIN_INPUT | MUX_MODE14)	/*	0x244	*/
    //		UART3_RXD	(PIN_INPUT | MUX_MODE14)	/*	0x248	*/
    //		UART3_TXD	(PIN_INPUT | MUX_MODE14)	/*	0x24C	*/
    //		RGMII0_TXC	(PIN_INPUT | MUX_MODE14)	/*	0x250	*/
    //		RGMII0_TXCTL	(PIN_INPUT | MUX_MODE14)	/*	0x254	*/
    		RGMII0_TXD3	(PIN_INPUT | MUX_MODE14)	/*	0x258	*/
    		RGMII0_TXD2	(PIN_INPUT | MUX_MODE14)	/*	0x25C	*/
    		RGMII0_TXD1	(PIN_INPUT | MUX_MODE14)	/*	0x260	*/
    		RGMII0_TXD0	(PIN_INPUT | MUX_MODE14)	/*	0x264	*/
    //		RGMII0_RXC	(PIN_INPUT | MUX_MODE14)	/*	0x268	*/
    //		RGMII0_RXCTL	(PIN_INPUT | MUX_MODE14)	/*	0x26C	*/
    //		RGMII0_RXD3	(PIN_INPUT | MUX_MODE14)	/*	0x270	*/
    //		RGMII0_RXD2	(PIN_INPUT | MUX_MODE14)	/*	0x274	*/
    		RGMII0_RXD1	(PIN_INPUT | MUX_MODE14)	/*	0x278	*/
    		RGMII0_RXD0	(PIN_INPUT | MUX_MODE14)	/*	0x27C	*/
    		USB1_DRVVBUS	(PIN_INPUT | MUX_MODE14)	/*	0x280	*/
    		USB2_DRVVBUS	(PIN_INPUT | MUX_MODE14)	/*	0x284	*/
    		GPIO6_14	(PIN_INPUT | MUX_MODE14)	/*	0x288	*/
    		GPIO6_15	(PIN_INPUT | MUX_MODE14)	/*	0x28C	*/
    		GPIO6_16	(PIN_INPUT | MUX_MODE14)	/*	0x290	*/
    		XREF_CLK0	(PIN_INPUT | MUX_MODE14)	/*	0x294	*/
    		XREF_CLK1	(PIN_INPUT | MUX_MODE14)	/*	0x298	*/
    		XREF_CLK2	(PIN_INPUT | MUX_MODE14)	/*	0x29C	*/
    		XREF_CLK3	(PIN_INPUT | MUX_MODE14)	/*	0x2A0	*/
    //		MCASP1_ACLKX	(PIN_INPUT | MUX_MODE14)	/*	0x2A4	*/
    //		MCASP1_FSX	(PIN_INPUT | MUX_MODE14)	/*	0x2A8	*/
    		MCASP1_ACLKR	(PIN_INPUT | MUX_MODE14)	/*	0x2AC	*/
    		MCASP1_FSR	(PIN_INPUT | MUX_MODE14)	/*	0x2B0	*/
    		//MCASP1_AXR0	(PIN_INPUT | MUX_MODE14)	/*	0x2B4	*/
    		//MCASP1_AXR1	(PIN_INPUT | MUX_MODE14)	/*	0x2B8	*/
    		MCASP1_AXR2	(PIN_INPUT | MUX_MODE14)	/*	0x2BC	*/
    //		MCASP1_AXR3	(PIN_INPUT | MUX_MODE14)	/*	0x2C0	*/
    //		MCASP1_AXR4	(PIN_INPUT | MUX_MODE14)	/*	0x2C4	*/
    //		MCASP1_AXR5	(PIN_INPUT | MUX_MODE14)	/*	0x2C8	*/
    //		MCASP1_AXR6	(PIN_INPUT | MUX_MODE14)	/*	0x2CC	*/
    //		MCASP1_AXR7	(PIN_INPUT | MUX_MODE14)	/*	0x2D0	*/
    		MCASP1_AXR8	(PIN_INPUT | MUX_MODE14)	/*	0x2D4	*/
    		MCASP1_AXR9	(PIN_INPUT | MUX_MODE14)	/*	0x2D8	*/
    		MCASP1_AXR10	(PIN_INPUT | MUX_MODE14)	/*	0x2DC	*/
    		MCASP1_AXR11	(PIN_INPUT | MUX_MODE14)	/*	0x2E0	*/
    		MCASP1_AXR12	(PIN_INPUT | MUX_MODE14)	/*	0x2E4	*/
    		MCASP1_AXR13	(PIN_INPUT | MUX_MODE14)	/*	0x2E8	*/
    		MCASP1_AXR14	(PIN_INPUT | MUX_MODE14)	/*	0x2EC	*/
    		MCASP1_AXR15	(PIN_INPUT | MUX_MODE14)	/*	0x2F0	*/
    //		MCASP2_AXR2	(PIN_INPUT | MUX_MODE14)	/*	0x30C	*/
    //		MCASP2_AXR3	(PIN_INPUT | MUX_MODE14)	/*	0x310	*/
    //		MCASP2_AXR4	(PIN_INPUT | MUX_MODE14)	/*	0x314	*/
    //		MCASP2_AXR5	(PIN_INPUT | MUX_MODE14)	/*	0x318	*/
    //		MCASP2_AXR6	(PIN_INPUT | MUX_MODE14)	/*	0x31C	*/
    //		MCASP2_AXR7	(PIN_INPUT | MUX_MODE14)	/*	0x320	*/
    //		MCASP3_ACLKX	(PIN_INPUT | MUX_MODE14)	/*	0x324	*/
    //		MCASP3_FSX	(PIN_INPUT | MUX_MODE14)	/*	0x328	*/
    		//MMC1_CLK	(PIN_INPUT | MUX_MODE14)	/*	0x354	*/
    		//MMC1_CMD	(PIN_INPUT | MUX_MODE14)	/*	0x358	*/
    		//MMC1_DAT0	(PIN_INPUT | MUX_MODE14)	/*	0x35C	*/
    		//MMC1_DAT1	(PIN_INPUT | MUX_MODE14)	/*	0x360	*/
    		//MMC1_DAT2	(PIN_INPUT | MUX_MODE14)	/*	0x364	*/
    		//MMC1_DAT3	(PIN_INPUT | MUX_MODE14)	/*	0x368	*/
    		//MMC1_SDCD	(PIN_INPUT | MUX_MODE14)	/*	0x36C	*/
    		//MMC1_SDWP	(PIN_INPUT | MUX_MODE14)	/*	0x370	*/
    		
    		//ulpi
    		//GPIO6_10	(PIN_INPUT | MUX_MODE14)	/*	0x374	*/
    		//GPIO6_11	(PIN_INPUT | MUX_MODE14)	/*	0x378	*/
    		//MMC3_CLK	(PIN_INPUT | MUX_MODE14)	/*	0x37C	*/
    		//MMC3_CMD	(PIN_INPUT | MUX_MODE14)	/*	0x380	*/
    		//MMC3_DAT0	(PIN_INPUT | MUX_MODE14)	/*	0x384	*/
    		//MMC3_DAT1	(PIN_INPUT | MUX_MODE14)	/*	0x388	*/
    		//MMC3_DAT2	(PIN_INPUT | MUX_MODE14)	/*	0x38C	*/
    		//MMC3_DAT3	(PIN_INPUT | MUX_MODE14)	/*	0x390	*/
    		//MMC3_DAT4	(PIN_INPUT | MUX_MODE14)	/*	0x394	*/
    		//MMC3_DAT5	(PIN_INPUT | MUX_MODE14)	/*	0x398	*/
    		//MMC3_DAT6	(PIN_INPUT | MUX_MODE14)	/*	0x39C	*/		
    		//MMC3_DAT7	(PIN_INPUT | MUX_MODE14)	/*	0x3A0	*/
    		
    		
    		//SPI1_SCLK	(PIN_INPUT | MUX_MODE14)	/*	0x3A4	*/
    		//SPI1_D1	(PIN_INPUT | MUX_MODE14)	/*	0x3A8	*/
    		//SPI1_D0	(PIN_INPUT | MUX_MODE14)	/*	0x3AC	*/
    		//SPI1_CS0	(PIN_INPUT | MUX_MODE14)	/*	0x3B0	*/
    		//SPI1_CS1	(PIN_INPUT | MUX_MODE14)	/*	0x3B4	*/
    		SPI1_CS2	(PIN_INPUT | MUX_MODE14)	/*	0x3B8	*/
    		//SPI1_CS3	(PIN_INPUT | MUX_MODE14)	/*	0x3BC	*/
    		//SPI2_SCLK	(PIN_INPUT | MUX_MODE14)	/*	0x3C0	*/
    		//SPI2_D1	(PIN_INPUT | MUX_MODE14)	/*	0x3C4	*/
    		//SPI2_D0	(PIN_INPUT | MUX_MODE14)	/*	0x3C8	*/
    		//SPI2_CS0	(PIN_INPUT | MUX_MODE14)	/*	0x3CC	*/
    		DCAN1_TX	(PIN_INPUT | MUX_MODE14)	/*	0x3D0	*/
    		DCAN1_RX	(PIN_INPUT | MUX_MODE14)	/*	0x3D4	*/
    		DCAN2_TX	(PIN_INPUT | MUX_MODE14)	/*	0x3D8	*/
    		DCAN2_RX	(PIN_INPUT | MUX_MODE14)	/*	0x3DC	*/
    		UART1_RXD	(PIN_INPUT | MUX_MODE14)	/*	0x3E0	*/
    		UART1_TXD	(PIN_INPUT | MUX_MODE14)	/*	0x3E4	*/
    		//UART1_CTSN	(PIN_INPUT | MUX_MODE14)	/*	0x3E8	*/
    		//UART1_RTSN	(PIN_INPUT | MUX_MODE14)	/*	0x3EC	*/
    		//UART2_RXD	(PIN_INPUT | MUX_MODE14)	/*	0x3F0	*/
    		//UART2_TXD	(PIN_INPUT | MUX_MODE14)	/*	0x3F4	*/
    		//UART2_CTSN	(PIN_INPUT | MUX_MODE14)	/*	0x3F8	*/
    		//UART2_RTSN	(PIN_INPUT | MUX_MODE14)	/*	0x3FC	*/
    		WAKEUP0	(PIN_INPUT | MUX_MODE14)	/*	0x418	*/
    		WAKEUP1	(PIN_INPUT | MUX_MODE14)	/*	0x41C	*/
    		WAKEUP2	(PIN_INPUT | MUX_MODE14)	/*	0x420	*/
    		WAKEUP3	(PIN_INPUT | MUX_MODE14)	/*	0x424	*/
    		TDI	(PIN_INPUT | MUX_MODE14)	/*	0x434	*/
    		TDO	(PIN_INPUT | MUX_MODE14)	/*	0x438	*/
    		TCLK	(PIN_INPUT | MUX_MODE14)	/*	0x43C	*/
    		TRSTN	(PIN_INPUT | MUX_MODE14)	/*	0x440	*/
    		RTCK	(PIN_INPUT | MUX_MODE14)	/*	0x444	*/
    		EMU2	(PIN_INPUT | MUX_MODE14)	/*	0x450	*/
    		EMU3	(PIN_INPUT | MUX_MODE14)	/*	0x454	*/
    
    //===================================================================================
    			
    		>;
    	};
    
    
    
    	uart3_pins_default: pinmux_uart3_pins {
    		pinctrl-single,pins = <
    			0x34c (PIN_INPUT | MUX_MODE4) /* mcasp5_axr0.uart3_rxd */
    			0x350 (PIN_OUTPUT | MUX_MODE4) /* mcasp5_axr1.uart3_txd */
    		>;
    	};
    
    	uart5_pins_default: pinmux_uart5_pins {
    		pinctrl-single,pins = <
    			VOUT1_D0 (WAKEUP_EN | PIN_INPUT | MUX_MODE2)	/* vout1_d0.uart5_rxd */
    			VOUT1_D1 (PIN_OUTPUT | MUX_MODE2)						/* vout1_d1.uart5_txd */
    		>;
    	};
    	
    	uart6_pins_default: pinmux_uart6_pins {
    		pinctrl-single,pins = <
    			VOUT1_D8 (PIN_INPUT | MUX_MODE2)  /* vout1_d8.uart6_rxd */
    			VOUT1_D9 (PIN_OUTPUT | MUX_MODE2) /* vout1_d9.uart6_txd */
    		>;
    	};
    
    	uart9_pins_default: pinmux_uart9_pins {
    		pinctrl-single,pins = <
    			MCASP5_ACLKX (PIN_INPUT | MUX_MODE8)  /* mcasp5_aclkx.uart9_rxd */
    			MCASP5_FSX (PIN_OUTPUT | MUX_MODE3) /* mcasp5_fsx.uart9_txd */						
    		>;
    	};		
    	
    	uart10_pins_default: pinmux_uart10_pins {
    		pinctrl-single,pins = <
    			VIN2A_D2 (PIN_INPUT | MUX_MODE8)  /* vin2a_d2.uart10_rxd */
    			VIN2A_D3 (PIN_OUTPUT | MUX_MODE8) /* vin2a_d3.uart10_txd */						
    			//VIN2A_D4 (PIN_INPUT | MUX_MODE8)  /* vin2a_d4.uart10_ctsn */
    			//VIN2A_D5 (PIN_OUTPUT | MUX_MODE8) /* vin2a_d5.uart10_rtsn */
    		>;
    	};	
    
    	
    	dcan1_pins_default: dcan1_pins_default {
    		pinctrl-single,pins = <
    			0x3d0   (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
    			0x418   (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
    		>;
    	};
    
    	dcan1_pins_sleep: dcan1_pins_sleep {
    		pinctrl-single,pins = <
    			0x3d0   (MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
    			0x418   (MUX_MODE15 | PULL_UP)	/* wakeup0.off */
    		>;
    	};
    
    	hdmi_i2c_sel_pin: pinmux_hdmi_i2c_sel_pin {
    		pinctrl-single,pins = <
    			/* this pin is used as a GPIO via mcasp */
    			0x2fc   (PIN_OUTPUT | MUX_MODE1) /* mcasp8_axr2 */
    		>;
    	};
    
    	hdmi_i2c_pins_i2c: pinmux_hdmi_i2c_pins_default {
    		pinctrl-single,pins = <
    			0x408   (PIN_INPUT | MUX_MODE0) /* i2c2_sda.i2c2_sda */
    			0x40c   (PIN_INPUT | MUX_MODE0) /* i2c2_scl.i2c2_scl */
    		>;
    	};
    
    	hdmi_i2c_pins_ddc: pinmux_hdmi_i2c_pins_ddc {
    		pinctrl-single,pins = <
    			0x408   (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
    			0x40c   (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
    		>;
    	};
    
    	mmc1_pins_default: pinmux_mmc1_default_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc1_pins_sdr12: pinmux_mmc1_sdr12_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc1_pins_hs: pinmux_mmc1_hs_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x35c (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc1_pins_sdr25: pinmux_mmc1_sdr25_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc1_pins_sdr50: pinmux_mmc1_sdr50_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc1_pins_ddr50: pinmux_mmc1_ddr50_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc1_pins_sdr104: pinmux_mmc1_sdr104_pins {
    		pinctrl-single,pins = <
    			0x354 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_clk.clk */
    			0x358 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_cmd.cmd */
    			0x35c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat0.dat0 */
    			0x360 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat1.dat1 */
    			0x364 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat2.dat2 */
    			0x368 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE0)	/* mmc1_dat3.dat3 */
    		>;
    	};
    
    	mmc2_pins_default: mmc2_pins_default {
    		pinctrl-single,pins = <
    			0x9c (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a23.mmc2_clk */
    			0xb0 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_cs1.mmc2_cmd */
    			0xa0 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a24.mmc2_dat0 */
    			0xa4 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a25.mmc2_dat1 */
    			0xa8 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a26.mmc2_dat2 */
    			0xac (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a27.mmc2_dat3 */
    			0x8c (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a19.mmc2_dat4 */
    			0x90 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a20.mmc2_dat5 */
    			0x94 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a21.mmc2_dat6 */
    			0x98 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a22.mmc2_dat7 */
    		>;
    	};
    
    	mmc2_pins_hs: mmc2_pins_hs {
    		pinctrl-single,pins = <
    			0x9c (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a23.mmc2_clk */
    			0xb0 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_cs1.mmc2_cmd */
    			0xa0 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a24.mmc2_dat0 */
    			0xa4 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a25.mmc2_dat1 */
    			0xa8 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a26.mmc2_dat2 */
    			0xac (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a27.mmc2_dat3 */
    			0x8c (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a19.mmc2_dat4 */
    			0x90 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a20.mmc2_dat5 */
    			0x94 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a21.mmc2_dat6 */
    			0x98 (PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a22.mmc2_dat7 */
    		>;
    	};
    
            mmc2_pins_ddr_3_3v: pinmux_mmc2_ddr_3_3v_pins {
                    pinctrl-single,pins = <
                            0x9c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a23.mmc2_clk */
                            0xb0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
                            0xa0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
                            0xa4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
                            0xa8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
                            0xac (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
                            0x8c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
                            0x90 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
                            0x94 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
                            0x98 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
                    >;
            };
    
    	mmc2_pins_ddr_1_8v: pinmux_mmc2_ddr_1_8v_pins {
    		pinctrl-single,pins = <
    			0x9c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a23.mmc2_clk */
    			0xb0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
    			0xa0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
    			0xa4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
    			0xa8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
    			0xac (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
    			0x8c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
    			0x90 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
    			0x94 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
    			0x98 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
    		>;
    	};
    
    	mmc2_pins_hs200_1_8v: mmc2_pins_hs200_1_8v {
    		pinctrl-single,pins = <
    			0x9c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a23.mmc2_clk */
    			0xb0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
    			0xa0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
    			0xa4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
    			0xa8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
    			0xac (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
    			0x8c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
    			0x90 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
    			0x94 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
    			0x98 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
    		>;
    	};
    
    	mmc4_pins_default: mmc4_pins_default {
    		pinctrl-single,pins = <
    			0x3e8 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
    			0x3ec (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
    			0x3f0 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
    			0x3f4 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
    			0x3f8 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
    			0x3fC (PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
    		>;
    	};
    
    	mmc4_pins_hs: mmc4_pins_hs {
    		pinctrl-single,pins = <
    			0x3e8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
    			0x3ec (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
    			0x3f0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
    			0x3f4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
    			0x3f8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
    			0x3fC (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
    		>;
    	};
    
    	mmc4_pins_sdr12: mmc4_pins_sdr12 {
    		pinctrl-single,pins = <
    			0x3e8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
    			0x3eC (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
    			0x3f0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
    			0x3f4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
    			0x3f8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
    			0x3fc (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
    		>;
    	};
    
    	mmc4_pins_sdr25: mmc4_pins_sdr25 {
    		pinctrl-single,pins = <
    			0x3e8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
    			0x3eC (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
    			0x3f0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
    			0x3f4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
    			0x3f8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
    			0x3fc (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
    		>;
    	};
    };
    
    &dra7_iodelay_core {
    
    	mmc1_iodelay_ddr50_rev11_conf: mmc1_iodelay_ddr50_rev11_conf {
    		pinctrl-single,pins = <
    			0x618 (A_DELAY(572) | G_DELAY(540))	/* CFG_MMC1_CLK_IN */
    			0x624 (A_DELAY(0) | G_DELAY(600))	/* CFG_MMC1_CMD_IN */
    			0x630 (A_DELAY(403) | G_DELAY(120))	/* CFG_MMC1_DAT0_IN */
    			0x63c (A_DELAY(23) | G_DELAY(60))	/* CFG_MMC1_DAT1_IN */
    			0x648 (A_DELAY(25) | G_DELAY(60))	/* CFG_MMC1_DAT2_IN */
    			0x654 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_IN */
    			0x620 (A_DELAY(1525) | G_DELAY(0))	/* CFG_MMC1_CLK_OUT */
    			0x628 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CMD_OEN */
    			0x62c (A_DELAY(55) | G_DELAY(0))	/* CFG_MMC1_CMD_OUT */
    			0x634 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT0_OEN */
    			0x638 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT0_OUT */
    			0x640 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OEN */
    			0x644 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OUT */
    			0x64c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OEN */
    			0x650 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OUT */
    			0x658 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OEN */
    			0x65c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OUT */
    		>;
    	};
    
    	mmc1_iodelay_ddr50_rev20_conf: mmc1_iodelay_ddr50_rev20_conf {
    		pinctrl-single,pins = <
    			0x618 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CLK_IN */
    			0x620 (A_DELAY(1271) | G_DELAY(0))	/* CFG_MMC1_CLK_OUT */
    			0x624 (A_DELAY(229) | G_DELAY(0))	/* CFG_MMC1_CMD_IN */
    			0x628 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CMD_OEN */
    			0x62C (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CMD_OUT */
    			0x630 (A_DELAY(850) | G_DELAY(0))	/* CFG_MMC1_DAT0_IN */
    			0x634 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT0_OEN */
    			0x638 (A_DELAY(20) | G_DELAY(0))	/* CFG_MMC1_DAT0_OUT */
    			0x63C (A_DELAY(468) | G_DELAY(0))	/* CFG_MMC1_DAT1_IN */
    			0x640 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OEN */
    			0x644 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OUT */
    			0x648 (A_DELAY(466) | G_DELAY(0))	/* CFG_MMC1_DAT2_IN */
    			0x64C (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OEN */
    			0x650 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OUT */
    			0x654 (A_DELAY(399) | G_DELAY(0))	/* CFG_MMC1_DAT3_IN */
    			0x658 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OEN */
    			0x65C (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OUT */
    		>;
    	};
    
    	mmc1_iodelay_sdr104_rev11_conf: mmc1_iodelay_sdr104_rev11_conf {
    		pinctrl-single,pins = <
    			0x620 (A_DELAY(1063) | G_DELAY(17))	/* CFG_MMC1_CLK_OUT */
    			0x628 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CMD_OEN */
    			0x62c (A_DELAY(23) | G_DELAY(0))	/* CFG_MMC1_CMD_OUT */
    			0x634 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT0_OEN */
    			0x638 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT0_OUT */
    			0x640 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OEN */
    			0x644 (A_DELAY(2) | G_DELAY(0))		/* CFG_MMC1_DAT1_OUT */
    			0x64c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OEN */
    			0x650 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OUT */
    			0x658 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OEN */
    			0x65c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OUT */
    		>;
    	};
    
    	mmc1_iodelay_sdr104_rev20_conf: mmc1_iodelay_sdr104_rev20_conf {
    		pinctrl-single,pins = <
    			0x620 (A_DELAY(600) | G_DELAY(400))	/* CFG_MMC1_CLK_OUT */
    			0x628 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CMD_OEN */
    			0x62c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_CMD_OUT */
    			0x634 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT0_OEN */
    			0x638 (A_DELAY(30) | G_DELAY(0))	/* CFG_MMC1_DAT0_OUT */
    			0x640 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OEN */
    			0x644 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT1_OUT */
    			0x64c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OEN */
    			0x650 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT2_OUT */
    			0x658 (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OEN */
    			0x65c (A_DELAY(0) | G_DELAY(0))		/* CFG_MMC1_DAT3_OUT */
    		>;
    	};
    
    	mmc2_iodelay_hs200_1_8v_rev11_conf: mmc2_iodelay_hs200_1_8v_rev11_conf {
    		pinctrl-single,pins = <
    			0x190 (A_DELAY(621) | G_DELAY(600))	/* CFG_GPMC_A19_OEN */
    			0x194 (A_DELAY(300) | G_DELAY(0))	/* CFG_GPMC_A19_OUT */
    			0x1a8 (A_DELAY(739) | G_DELAY(600))	/* CFG_GPMC_A20_OEN */
    			0x1ac (A_DELAY(240) | G_DELAY(0))	/* CFG_GPMC_A20_OUT */
    			0x1b4 (A_DELAY(812) | G_DELAY(600))	/* CFG_GPMC_A21_OEN */
    			0x1b8 (A_DELAY(240) | G_DELAY(0))	/* CFG_GPMC_A21_OUT */
    			0x1c0 (A_DELAY(954) | G_DELAY(600))	/* CFG_GPMC_A22_OEN */
    			0x1c4 (A_DELAY(60)  | G_DELAY(0))	/* CFG_GPMC_A22_OUT */
    			0x1d0 (A_DELAY(1340)| G_DELAY(420))	/* CFG_GPMC_A23_OUT */
    			0x1d8 (A_DELAY(935) | G_DELAY(600))	/* CFG_GPMC_A24_OEN */
    			0x1dc (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A24_OUT */
    			0x1e4 (A_DELAY(525) | G_DELAY(600))	/* CFG_GPMC_A25_OEN */
    			0x1e8 (A_DELAY(120) | G_DELAY(0))	/* CFG_GPMC_A25_OUT */
    			0x1f0 (A_DELAY(767) | G_DELAY(600))	/* CFG_GPMC_A26_OEN */
    			0x1f4 (A_DELAY(225) | G_DELAY(0))	/* CFG_GPMC_A26_OUT */
    			0x1fc (A_DELAY(565) | G_DELAY(600))	/* CFG_GPMC_A27_OEN */
    			0x200 (A_DELAY(60) | G_DELAY(0))	/* CFG_GPMC_A27_OUT */
    			0x364 (A_DELAY(969) | G_DELAY(600))	/* CFG_GPMC_CS1_OEN */
    			0x368 (A_DELAY(180) | G_DELAY(0))	/* CFG_GPMC_CS1_OUT */
    	      >;
    	};
    
    	mmc2_iodelay_hs200_1_8v_rev20_conf: mmc2_iodelay_hs200_1_8v_rev20_conf {
    		pinctrl-single,pins = <
    			0x190 (A_DELAY(274) | G_DELAY(0))       /* CFG_GPMC_A19_OEN */
    			0x194 (A_DELAY(162) | G_DELAY(0))       /* CFG_GPMC_A19_OUT */
    			0x1a8 (A_DELAY(401) | G_DELAY(0))       /* CFG_GPMC_A20_OEN */
    			0x1ac (A_DELAY(73) | G_DELAY(0))        /* CFG_GPMC_A20_OUT */
    			0x1b4 (A_DELAY(465) | G_DELAY(0))       /* CFG_GPMC_A21_OEN */
    			0x1b8 (A_DELAY(115) | G_DELAY(0))       /* CFG_GPMC_A21_OUT */
    			0x1c0 (A_DELAY(633) | G_DELAY(0))       /* CFG_GPMC_A22_OEN */
    			0x1c4 (A_DELAY(47) | G_DELAY(0))        /* CFG_GPMC_A22_OUT */
    			0x1d0 (A_DELAY(935) | G_DELAY(280))     /* CFG_GPMC_A23_OUT */
    			0x1d8 (A_DELAY(621) | G_DELAY(0))       /* CFG_GPMC_A24_OEN */
    			0x1dc (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A24_OUT */
    			0x1e4 (A_DELAY(183) | G_DELAY(0))       /* CFG_GPMC_A25_OEN */
    			0x1e8 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A25_OUT */
    			0x1f0 (A_DELAY(467) | G_DELAY(0))       /* CFG_GPMC_A26_OEN */
    			0x1f4 (A_DELAY(0) | G_DELAY(0))         /* CFG_GPMC_A26_OUT */
    			0x1fc (A_DELAY(262) | G_DELAY(0))       /* CFG_GPMC_A27_OEN */
    			0x200 (A_DELAY(46) | G_DELAY(0))        /* CFG_GPMC_A27_OUT */
    			0x364 (A_DELAY(684) | G_DELAY(0))       /* CFG_GPMC_CS1_OEN */
    			0x368 (A_DELAY(76) | G_DELAY(0))        /* CFG_GPMC_CS1_OUT */
    	      >;
    	};
    
    	mmc2_iodelay_ddr_1_8v_rev11_conf: mmc2_iodelay_ddr_1_8v_rev11_conf {
    		pinctrl-single,pins = <
    			0x18c (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A19_IN */
    			0x1a4 (A_DELAY(274) | G_DELAY(240))	/* CFG_GPMC_A20_IN */
    			0x1b0 (A_DELAY(0) | G_DELAY(60))	/* CFG_GPMC_A21_IN */
    			0x1bc (A_DELAY(0) | G_DELAY(60))	/* CFG_GPMC_A22_IN */
    			0x1c8 (A_DELAY(514) | G_DELAY(360))	/* CFG_GPMC_A23_IN */
    			0x1d4 (A_DELAY(187) | G_DELAY(120))	/* CFG_GPMC_A24_IN */
    			0x1e0 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A25_IN */
    			0x1ec (A_DELAY(0) | G_DELAY(60))	/* CFG_GPMC_A26_IN */
    			0x1f8 (A_DELAY(121) | G_DELAY(60))	/* CFG_GPMC_A27_IN */
    			0x360 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_CS1_IN */
    			0x190 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A19_OEN */
    			0x194 (A_DELAY(174) | G_DELAY(0))	/* CFG_GPMC_A19_OUT */
    			0x1a8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A20_OEN */
    			0x1ac (A_DELAY(168) | G_DELAY(0))	/* CFG_GPMC_A20_OUT */
    			0x1b4 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A21_OEN */
    			0x1b8 (A_DELAY(136) | G_DELAY(0))	/* CFG_GPMC_A21_OUT */
    			0x1c0 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A22_OEN */
    			0x1c4 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A22_OUT */
    			0x1d0 (A_DELAY(879) | G_DELAY(0))	/* CFG_GPMC_A23_OUT */
    			0x1d8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A24_OEN */
    			0x1dc (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A24_OUT */
    			0x1e4 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A25_OEN */
    			0x1e8 (A_DELAY(34) | G_DELAY(0))	/* CFG_GPMC_A25_OUT */
    			0x1f0 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A26_OEN */
    			0x1f4 (A_DELAY(120) | G_DELAY(0))	/* CFG_GPMC_A26_OUT */
    			0x1fc (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A27_OEN */
    			0x200 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A27_OUT */
    			0x364 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_CS1_OEN */
    			0x368 (A_DELAY(11) | G_DELAY(0))	/* CFG_GPMC_CS1_OUT */
    		>;
    	};
    
    	mmc2_iodelay_ddr_1_8v_rev20_conf: mmc2_iodelay_ddr_1_8v_rev20_conf {
    		pinctrl-single,pins = <
    			0x18c (A_DELAY(270) | G_DELAY(0))	/* CFG_GPMC_A19_IN */
    			0x1a4 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A20_IN */
    			0x1b0 (A_DELAY(170) | G_DELAY(0))	/* CFG_GPMC_A21_IN */
    			0x1bc (A_DELAY(758) | G_DELAY(0))	/* CFG_GPMC_A22_IN */
    			0x1c8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A23_IN */
    			0x1d4 (A_DELAY(81) | G_DELAY(0))	/* CFG_GPMC_A24_IN */
    			0x1e0 (A_DELAY(286) | G_DELAY(0))	/* CFG_GPMC_A25_IN */
    			0x1ec (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A26_IN */
    			0x1f8 (A_DELAY(123) | G_DELAY(0))	/* CFG_GPMC_A27_IN */
    			0x360 (A_DELAY(346) | G_DELAY(0))	/* CFG_GPMC_CS1_IN */
    			0x190 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A19_OEN */
    			0x194 (A_DELAY(55) | G_DELAY(0))	/* CFG_GPMC_A19_OUT */
    			0x1a8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A20_OEN */
    			0x1ac (A_DELAY(422) | G_DELAY(0))	/* CFG_GPMC_A20_OUT */
    			0x1b4 (A_DELAY(642) | G_DELAY(0))	/* CFG_GPMC_A21_OEN */
    			0x1b8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A21_OUT */
    			0x1c0 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A22_OEN */
    			0x1c4 (A_DELAY(128) | G_DELAY(0))	/* CFG_GPMC_A22_OUT */
    			0x1d0 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A23_OUT */
    			0x1d8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A24_OEN */
    			0x1dc (A_DELAY(395) | G_DELAY(0))	/* CFG_GPMC_A24_OUT */
    			0x1e4 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A25_OEN */
    			0x1e8 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A25_OUT */
    			0x1f0 (A_DELAY(623) | G_DELAY(0))	/* CFG_GPMC_A26_OEN */
    			0x1f4 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A26_OUT */
    			0x1fc (A_DELAY(54) | G_DELAY(0))	/* CFG_GPMC_A27_OEN */
    			0x200 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_A27_OUT */
    			0x364 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_CS1_OEN */
    			0x368 (A_DELAY(0) | G_DELAY(0))		/* CFG_GPMC_CS1_OUT */
    		>;
    	};
    
    	mmc4_iodelay_ds_rev11_conf: mmc4_iodelay_ds_rev11_conf {
    		pinctrl-single,pins = <
    			0x840 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_CTSN_IN */
    			0x848 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_CTSN_OUT */
    			0x84c (A_DELAY(96) | G_DELAY(0))	/* CFG_UART1_RTSN_IN */
    			0x850 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OEN */
    			0x854 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OUT */
    			0x870 (A_DELAY(582) | G_DELAY(0))	/* CFG_UART2_CTSN_IN */
    			0x874 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OEN */
    			0x878 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OUT */
    			0x87c (A_DELAY(391) | G_DELAY(0))	/* CFG_UART2_RTSN_IN */
    			0x880 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OEN */
    			0x884 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OUT */
    			0x888 (A_DELAY(561) | G_DELAY(0))	/* CFG_UART2_RXD_IN */
    			0x88c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OEN */
    			0x890 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OUT */
    			0x894 (A_DELAY(588) | G_DELAY(0))	/* CFG_UART2_TXD_IN */
    			0x898 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OEN */
    			0x89c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OUT */
    		>;
    	};
    
    	mmc4_iodelay_ds_rev20_conf: mmc4_iodelay_ds_rev20_conf {
    		pinctrl-single,pins = <
    			0x840 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_CTSN_IN */
    			0x848 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_CTSN_OUT */
    			0x84c (A_DELAY(307) | G_DELAY(0))	/* CFG_UART1_RTSN_IN */
    			0x850 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OEN */
    			0x854 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OUT */
    			0x870 (A_DELAY(785) | G_DELAY(0))	/* CFG_UART2_CTSN_IN */
    			0x874 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OEN */
    			0x878 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OUT */
    			0x87c (A_DELAY(613) | G_DELAY(0))	/* CFG_UART2_RTSN_IN */
    			0x880 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OEN */
    			0x884 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OUT */
    			0x888 (A_DELAY(683) | G_DELAY(0))	/* CFG_UART2_RXD_IN */
    			0x88c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OEN */
    			0x890 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OUT */
    			0x894 (A_DELAY(835) | G_DELAY(0))	/* CFG_UART2_TXD_IN */
    			0x898 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OEN */
    			0x89c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OUT */
    		>;
    	};
    
    	mmc4_iodelay_sdr12_hs_sdr25_rev11_conf: mmc4_iodelay_sdr12_hs_sdr25_rev11_conf {
    		pinctrl-single,pins = <
    			0x840 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_CTSN_IN */
    			0x848 (A_DELAY(2651) | G_DELAY(0))	/* CFG_UART1_CTSN_OUT */
    			0x84c (A_DELAY(1572) | G_DELAY(0))	/* CFG_UART1_RTSN_IN */
    			0x850 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OEN */
    			0x854 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OUT */
    			0x870 (A_DELAY(1913) | G_DELAY(0))	/* CFG_UART2_CTSN_IN */
    			0x874 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OEN */
    			0x878 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OUT */
    			0x87c (A_DELAY(1721) | G_DELAY(0))	/* CFG_UART2_RTSN_IN */
    			0x880 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OEN */
    			0x884 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OUT */
    			0x888 (A_DELAY(1891) | G_DELAY(0))	/* CFG_UART2_RXD_IN */
    			0x88c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OEN */
    			0x890 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OUT */
    			0x894 (A_DELAY(1919) | G_DELAY(0))	/* CFG_UART2_TXD_IN */
    			0x898 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OEN */
    			0x89c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OUT */
    		>;
    	};
    
    	mmc4_iodelay_sdr12_hs_sdr25_rev20_conf: mmc4_iodelay_sdr12_hs_sdr25_rev20_conf {
    		pinctrl-single,pins = <
    			0x840 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_CTSN_IN */
    			0x848 (A_DELAY(1147) | G_DELAY(0))	/* CFG_UART1_CTSN_OUT */
    			0x84c (A_DELAY(1834) | G_DELAY(0))	/* CFG_UART1_RTSN_IN */
    			0x850 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OEN */
    			0x854 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART1_RTSN_OUT */
    			0x870 (A_DELAY(2165) | G_DELAY(0))	/* CFG_UART2_CTSN_IN */
    			0x874 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OEN */
    			0x878 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_CTSN_OUT */
    			0x87c (A_DELAY(1929) | G_DELAY(64))	/* CFG_UART2_RTSN_IN */
    			0x880 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OEN */
    			0x884 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RTSN_OUT */
    			0x888 (A_DELAY(1935) | G_DELAY(128))	/* CFG_UART2_RXD_IN */
    			0x88c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OEN */
    			0x890 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_RXD_OUT */
    			0x894 (A_DELAY(2172) | G_DELAY(44))	/* CFG_UART2_TXD_IN */
    			0x898 (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OEN */
    			0x89c (A_DELAY(0) | G_DELAY(0))		/* CFG_UART2_TXD_OUT */
    		>;
    	};
    };
    
    &i2c1 {
    	status = "okay";
    	clock-frequency = <400000>;
    
    	tps659038: tps659038@58 {
    		compatible = "ti,tps659038";
    		reg = <0x58>;
    
    		tps659038_pmic {
    			compatible = "ti,tps659038-pmic";
    
    			regulators {
    				smps123_reg: smps123 {
    					/* VDD_MPU */
    					regulator-name = "smps123";
    					regulator-min-microvolt = < 850000>;
    					regulator-max-microvolt = <1250000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				smps45_reg: smps45 {
    					/* VDD_DSPEVE */
    					regulator-name = "smps45";
    					regulator-min-microvolt = < 850000>;
    					regulator-max-microvolt = <1250000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				smps6_reg: smps6 {
    					/* VDD_GPU - over VDD_SMPS6 */
    					regulator-name = "smps6";
    					regulator-min-microvolt = <850000>;
    					regulator-max-microvolt = <1250000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				smps7_reg: smps7 {
    					/* CORE_VDD */
    					regulator-name = "smps7";
    					regulator-min-microvolt = <850000>;
    					regulator-max-microvolt = <1150000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				smps8_reg: smps8 {
    					/* VDD_IVAHD */
    					regulator-name = "smps8";
    					regulator-min-microvolt = < 850000>;
    					regulator-max-microvolt = <1250000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				smps9_reg: smps9 {
    					/* VDDS1V8 */
    					regulator-name = "smps9";
    					regulator-min-microvolt = <1800000>;
    					regulator-max-microvolt = <1800000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				ldo1_reg: ldo1 {
    					/* LDO1_OUT --> SDIO  */
    					regulator-name = "ldo1";
    					regulator-min-microvolt = <1800000>;
    					regulator-max-microvolt = <1800000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				ldo2_reg: ldo2 {
    					/* VDD_RTCIO */
    					/* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
    					regulator-name = "ldo2";
    					regulator-min-microvolt = <3300000>;
    					regulator-max-microvolt = <3300000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				ldo3_reg: ldo3 {
    					/* VDDA_1V8_PHY */
    					regulator-name = "ldo3";
    					regulator-min-microvolt = <1800000>;
    					regulator-max-microvolt = <1800000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				ldo9_reg: ldo9 {
    					/* VDD_RTC */
    					regulator-name = "ldo9";
    					regulator-min-microvolt = <1050000>;
    					regulator-max-microvolt = <1050000>;
    					regulator-always-on;
    					regulator-boot-on;
    					regulator-allow-bypass;
    				};
    
    				ldoln_reg: ldoln {
    					/* VDDA_1V8_PLL */
    					regulator-name = "ldoln";
    					regulator-min-microvolt = <1800000>;
    					regulator-max-microvolt = <1800000>;
    					regulator-always-on;
    					regulator-boot-on;
    				};
    
    				ldousb_reg: ldousb {
    					/* VDDA_3V_USB: VDDA_USBHS33 */
    					regulator-name = "ldousb";
    					regulator-min-microvolt = <3300000>;
    					regulator-max-microvolt = <3300000>;
    					regulator-boot-on;
    				};
    
    				/* REGEN1 is unused */
    
    				regen2: regen2 {
    					/* Needed for PMIC internal resources */
    					regulator-name = "regen2";
    					regulator-boot-on;
    					regulator-always-on;
    				};
    
    				/* REGEN3 is unused */
    
    				sysen1: sysen1 {
    					/* PMIC_REGEN_3V3 */
    					regulator-name = "sysen1";
    					regulator-boot-on;
    					regulator-always-on;
    				};
    
    				sysen2: sysen2 {
    					/* PMIC_REGEN_DDR */
    					regulator-name = "sysen2";
    					regulator-boot-on;
    					regulator-always-on;
    				};
    			};
    		};
    	};
    
    	pcf_lcd: gpio@20 {
    		status = "disabled";
    		compatible = "nxp,pcf8575";
    		reg = <0x20>;
    		gpio-controller;
    		#gpio-cells = <2>;
    		interrupt-parent = <&gpio6>;
    		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
    		interrupt-controller;
    		#interrupt-cells = <2>;
    	};
    
    	pcf_gpio_21: gpio@21 {
    		status = "disabled";
    		compatible = "ti,pcf8575";
    		reg = <0x21>;
    		lines-initial-states = <0x1408>;
    		gpio-controller;
    		#gpio-cells = <2>;
    		interrupt-parent = <&gpio6>;
    		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
    		interrupt-controller;
    		#interrupt-cells = <2>;
    	};
    #if 0
    	tlv320aic3106: tlv320aic3106@19 {
    		#sound-dai-cells = <0>;
    		compatible = "ti,tlv320aic3106";
    		status = "disabled";
    		reg = <0x19>;
    		adc-settle-ms = <40>;
    		ai3x-micbias-vg = <1>;		/* 2.0V */
    		//status = "okay";
    		status = "disabled";
    
    		/* Regulators */
    		AVDD-supply = <&evm_3v3_sw>;
    		IOVDD-supply = <&evm_3v3_sw>;
    		DRVDD-supply = <&evm_3v3_sw>;
    		DVDD-supply = <&aic_dvdd>;
    	};
    #endif
    };
    
    i2c_p3_exp: &i2c2 {
    	status = "okay";
    	clock-frequency = <400000>;
    
    #if 0
    	tvp_5158: tvp5158@58 {
    		compatible= "ti,tvp5158";
    		reg = <0x58>;
    
    		port {
    			tvp_decoder: endpoint@0 {
    				remote-endpoint = <&vin2a>;
    				//channels = <0 2 4 6>;
    				channels = <0>;
    				//pixel-mux;
    				//pclk-sample = <0>;
    			};
    		};
    	};
    #endif
    
    	pcf_hdmi: gpio@26 {
    		status = "disabled";
    		compatible = "nxp,pcf8575";
    		reg = <0x26>;
    		gpio-controller;
    		#gpio-cells = <2>;
    		p1 {
    			/* vin6_sel_s0: high: VIN6, low: audio */
    			gpio-hog;
    			gpios = <1 GPIO_ACTIVE_HIGH>;
    			output-low;
    			line-name = "vin6_sel_s0";
    		};
    	};
    
    	ov10633@37 {
    		status = "okay";
    		compatible = "ovti,ov10633";
    		reg = <0x37>;
    
    		mux-gpios = <&pcf_hdmi 3 GPIO_ACTIVE_LOW>; /* CAM_FPD_MUX_S0 */
    		port {
    			onboardLI: endpoint {
    				//remote-endpoint = <&vin1a>;
    				remote-endpoint = <&vin4b>;
    				//hsync-active = <1>;
    				//vsync-active = <1>;
    				pclk-sample = <0>;
    				channels = <0>;
    			};
    		};
    	};
    
    	disp_ser: serializer@1b {
    		status = "disabled" ;
    		compatible = "ti,ds90uh925q";
    		reg = <0x1b>;
    
    		#address-cells = <1>;
    		#size-cells = <0>;
    		ranges = <0x2c 0x2c>,
    			<0x1c 0x1c>;
    
    		disp_des: deserializer@2c {
    			compatible = "ti,ds90uh928q";
    			reg = <0x2c>;
    			slave-mode;
    		};
    
    		/* TLC chip for LCD panel power and backlight */
    		fpd_disp: tlc59108@1c {
    			status = "disabled";
    			reg = <0x1c>;
    			compatible = "ti,tlc59108-fpddisp";
    			enable-gpios = <&pcf_gpio_21 0 GPIO_ACTIVE_LOW>;
    			/* P0, SEL_GPMC_AD_VID_S0 */
    
    			port@lcd3 {
    					fpd_in: endpoint {
    					remote-endpoint = <&dpi_out3>;
    				};
    			};
    		};
    	};
    };
    
    &i2c3 {
    	status = "okay";
    	clock-frequency = <400000>;
    };
    
    &mcspi1 {
            status = "okay";
            ti,pindir-d0-out-d1-in;
            spidev@0
            {    
        spi-max-frequency = <16000000>;
        reg = <0>; 
            compatible = "rohm,dh2228fv";   
            status = "okay" ; 
            };   
            spidev@1
            {    
        spi-max-frequency = <16000000>;
        reg = <1>; 
            compatible = "rohm,dh2228fv";
            status = "okay" ; 
            };     
            spidev@3
            {    
        spi-max-frequency = <16000000>;
        reg = <3>; 
            compatible = "rohm,dh2228fv";   
            status = "okay" ; 
            };
    };
    
    &mcspi2 {
            status = "okay";
            ti,pindir-d0-out-d1-in;
            spidev@0
            {
        spi-max-frequency = <16000000>;
        reg = <0>;
            compatible = "rohm,dh2228fv";
            };
    };
    
    &mcspi3 {
            status = "okay";
            ti,pindir-d0-out-d1-in;
            spidev@0
            {
        spi-max-frequency = <16000000>;
        reg = <0>;
            compatible = "rohm,dh2228fv";
            };
    };
    
    &uart1 {
    	status = "okay";
    	pinctrl-names = "default";
    	pinctrl-0 = <&uart1_pins>;	
    		
    	//interrupts-extended = <&gic GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH &dra7_pmx_core 0x3e0>;	       
    };
    
    &uart2 {
    	status = "okay";
    };
    
    &uart3 {
    	status = "okay";
    	/* gpios = <&pcf_gpio_21 14 GPIO_ACTIVE_LOW>; */
    	pinctrl-names = "default";
    	pinctrl-0 = <&uart3_pins_default>;	
    };
    
    &uart5 {
    	status = "okay";
    	pinctrl-names = "default";
    	pinctrl-0 = <&uart5_pins_default>;	
    };
    
    &uart6 {
    	status = "okay";
    	pinctrl-names = "default";
    	pinctrl-0 = <&uart6_pins_default>;	
    };
    
    &uart9 {
    	status = "okay";
    	pinctrl-names = "default";
    	pinctrl-0 = <&uart9_pins_default>;	
    };
    
    
    &uart10 {
    	status = "okay";
    	pinctrl-names = "default";
    	pinctrl-0 = <&uart10_pins_default>;	
    };
    
    
    
    &mmc1 {
    	status = "okay";
    	vmmc-supply = <&evm_1v8_sd>;
    	vmmc_aux-supply = <&ldo1_reg>;
    	bus-width = <4>;
    	//cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
    	max-frequency = <192000000>;
    	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
    	pinctrl-0 = <&mmc1_pins_default>;
    	pinctrl-1 = <&mmc1_pins_hs>;
    	pinctrl-2 = <&mmc1_pins_sdr12>;
    	pinctrl-3 = <&mmc1_pins_sdr25>;
    	pinctrl-4 = <&mmc1_pins_sdr50>;
    	pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr50_rev11_conf>;
    	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
    	pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr50_rev20_conf>;
    	pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
    };
    
    #if 0
    &mmc2 {
    	status = "okay";
    	vmmc-supply = <&evm_3v3_sw>;
    	bus-width = <8>;
    	max-frequency = <192000000>;
    	pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
    	pinctrl-0 = <&mmc2_pins_default>;
    	pinctrl-1 = <&mmc2_pins_hs>;
    	pinctrl-2 = <&mmc2_pins_ddr_1_8v &mmc2_iodelay_ddr_1_8v_rev11_conf>;
    	pinctrl-3 = <&mmc2_pins_ddr_1_8v &mmc2_iodelay_ddr_1_8v_rev20_conf>;
    	pinctrl-4 = <&mmc2_pins_hs200_1_8v &mmc2_iodelay_hs200_1_8v_rev11_conf>;
    	pinctrl-5 = <&mmc2_pins_hs200_1_8v &mmc2_iodelay_hs200_1_8v_rev20_conf>;
    };
    #else
    &mmc2 {
            status = "okay";
            vmmc-supply = <&evm_3v3_sw>;
            bus-width = <8>; 
    	ti,non-removable;
    	max-frequency = <192000000>;
    
            pinctrl-names = "default", "hs", "ddr_1_8v";
            pinctrl-0 = <&mmc2_pins_default>;
            pinctrl-1 = <&mmc2_pins_hs>;
            pinctrl-2 = <&mmc2_pins_ddr_1_8v>;
    };
    #endif
    
    #if 0
    &mmc4 {
    	status = "okay";
    	vmmc-supply = <&vmmcwl_fixed>;
    	bus-width = <4>;
    	cap-power-off-card;
    	keep-power-in-suspend;
    	ti,non-removable;
    
    	pinctrl-names = "default-rev11", "default", "hs-rev11", "hs", "sdr12-rev11", "sdr12", "sdr25-rev11", "sdr25";
    	pinctrl-0 = <&mmc4_pins_default &mmc4_iodelay_ds_rev11_conf>;
    	pinctrl-1 = <&mmc4_pins_default &mmc4_iodelay_ds_rev20_conf>;
    	pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
    	pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
    	pinctrl-4 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
    	pinctrl-5 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
    	pinctrl-6 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
    	pinctrl-7 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
    
    	#address-cells = <1>;
    	#size-cells = <0>;
    	wlcore: wlcore@0 {
    		compatible = "ti,wl1835";
    		reg = <2>;
    		interrupt-parent = <&gpio5>;
    		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
    	};
    };
    #else
    &mmc4 {
            status = "okay";
    
            bus-width = <4>; 
            pinctrl-names = "default";
            pinctrl-0 = <&mmc4_pins_default>;
    	vmmc-supply = <&evm_3v3_sw>;
    /*
            status = "okay";
            vmmc-supply = <&vmmcwl_fixed>;
            bus-width = <4>; 
            cap-power-off-card;
            keep-power-in-suspend;
            ti,non-removable;
    
            #address-cells = <1>; 
            #size-cells = <0>; 
            wlcore: wlcore@0 {
                    compatible = "ti,wlcore";
                    reg = <2>;
                    interrupt-parent = <&gpio5>;
                    interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
            };
    */
    
    };
    #endif
    
    &oppdm_mpu {
    	vdd-supply = <&smps123_reg>;
    };
    
    &oppdm_dspeve {
    	vdd-supply = <&smps45_reg>;
    };
    
    &oppdm_gpu {
    	vdd-supply = <&smps6_reg>;
    };
    
    &oppdm_ivahd {
    	vdd-supply = <&smps8_reg>;
    };
    
    &oppdm_core {
    	vdd-supply = <&smps7_reg>;
    };
    
    &qspi {
    	//status = "okay";
    	status = "disabled";
    
    	spi-max-frequency = <64000000>;
    	m25p80@0 {
    		compatible = "s25fl256s1";
    		spi-max-frequency = <64000000>;
    		reg = <0>;
    		spi-tx-bus-width = <1>;
    		spi-rx-bus-width = <4>;
    		#address-cells = <1>;
    		#size-cells = <1>;
    
    		/* MTD partition table.
    		 * The ROM checks the first four physical blocks
    		 * for a valid file to boot and the flash here is
    		 * 64KiB block size.
    		 */
    		partition@0 {
    			label = "QSPI.SPL";
    			reg = <0x00000000 0x000040000>;
    		};
    		partition@1 {
    			label = "QSPI.u-boot";
    			reg = <0x00040000 0x00100000>;
    		};
    		partition@2 {
    			label = "QSPI.u-boot-spl-os";
    			reg = <0x00140000 0x00080000>;
    		};
    		partition@3 {
    			label = "QSPI.u-boot-env";
    			reg = <0x001c0000 0x00010000>;
    		};
    		partition@4 {
    			label = "QSPI.u-boot-env.backup1";
    			reg = <0x001d0000 0x0010000>;
    		};
    		partition@5 {
    			label = "QSPI.kernel";
    			reg = <0x001e0000 0x0800000>;
    		};
    		partition@6 {
    			label = "QSPI.file-system";
    			reg = <0x009e0000 0x01620000>;
    		};
    	};
    };
    
    &omap_dwc3_1 {
    	//extcon = <&extcon_usb1>;
    };
    
    &omap_dwc3_2 {
    	//extcon = <&extcon_usb2>;
    };
    
    &usb1 {
    	status = "ok";
    	dr_mode = "host";
    };
    
    &usb2 {
    	status = "ok";
    	dr_mode = "host";
    };
    
    &usb3 {
    	pinctrl-names = "default";
    	pinctrl-0 = <&usb3_pins>;
    	status = "ok";
    	dr_mode = "host";
        snps,hsphy_interface = "ulpi";
    };
    
    &elm {
    	status = "okay";
    };
    
    &gpmc {
    	status = "disabled";
    	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
    	nand@0,0 {
    		compatible = "ti,omap2-nand";
    		reg = <0 0 4>;		/* device IO registers */
    		interrupt-parent = <&gpmc>;
    		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
    			     <1 IRQ_TYPE_NONE>; /* termcount */
    		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
    		ti,nand-ecc-opt = "bch8";
    		ti,elm-id = <&elm>;
    		nand-bus-width = <16>;
    		gpmc,device-width = <2>;
    		gpmc,sync-clk-ps = <0>;
    		gpmc,cs-rd-off-ns = <80>;
    		gpmc,cs-wr-off-ns = <80>;
    		gpmc,adv-on-ns = <0>;
    		gpmc,adv-rd-off-ns = <60>;
    		gpmc,adv-wr-off-ns = <60>;
    		gpmc,we-on-ns = <10>;
    		gpmc,we-off-ns = <50>;
    		gpmc,oe-on-ns = <4>;
    		gpmc,oe-off-ns = <40>;
    		gpmc,access-ns = <40>;
    		gpmc,wr-access-ns = <80>;
    		gpmc,rd-cycle-ns = <80>;
    		gpmc,wr-cycle-ns = <80>;
    		gpmc,bus-turnaround-ns = <0>;
    		gpmc,cycle2cycle-delay-ns = <0>;
    		gpmc,clk-activation-ns = <0>;
    		gpmc,wr-data-mux-bus-ns = <0>;
    		/* MTD partition table */
    		/* All SPL-* partitions are sized to minimal length
    		 * which can be independently programmable. For
    		 * NAND flash this is equal to size of erase-block */
    		#address-cells = <1>;
    		#size-cells = <1>;
    		partition@0 {
    			label = "NAND.SPL";
    			reg = <0x00000000 0x000020000>;
    		};
    		partition@1 {
    			label = "NAND.SPL.backup1";
    			reg = <0x00020000 0x00020000>;
    		};
    		partition@2 {
    			label = "NAND.SPL.backup2";
    			reg = <0x00040000 0x00020000>;
    		};
    		partition@3 {
    			label = "NAND.SPL.backup3";
    			reg = <0x00060000 0x00020000>;
    		};
    		partition@4 {
    			label = "NAND.u-boot-spl-os";
    			reg = <0x00080000 0x00040000>;
    		};
    		partition@5 {
    			label = "NAND.u-boot";
    			reg = <0x000c0000 0x00100000>;
    		};
    		partition@6 {
    			label = "NAND.u-boot-env";
    			reg = <0x001c0000 0x00020000>;
    		};
    		partition@7 {
    			label = "NAND.u-boot-env.backup1";
    			reg = <0x001e0000 0x00020000>;
    		};
    		partition@8 {
    			label = "NAND.kernel";
    			reg = <0x00200000 0x00800000>;
    		};
    		partition@9 {
    			label = "NAND.file-system";
    			reg = <0x00a00000 0x0f600000>;
    		};
    	};
    };
    
    &usb2_phy1 {
    	phy-supply = <&ldousb_reg>;
    };
    
    &usb2_phy2 {
    	phy-supply = <&ldousb_reg>;
    };
    
    
    &gpio7 {
    	ti,no-reset-on-init;
    	ti,no-idle-on-init;
    };
    
    &mac {
    	status = "okay";
    	dual_emac;
    };
    
    &cpsw_emac0 {
    	phy_id = <&davinci_mdio>, <2>;
    	phy-mode = "rgmii";
    	dual_emac_res_vlan = <1>;
    };
    
    &cpsw_emac1 {
    	phy_id = <&davinci_mdio>, <3>;
    	phy-mode = "rgmii";
    	dual_emac_res_vlan = <2>;
    };
    
    &dcan1 {
    	status = "ok";
    	pinctrl-names = "default", "sleep", "active";
    	pinctrl-0 = <&dcan1_pins_sleep>;
    	pinctrl-1 = <&dcan1_pins_sleep>;
    	pinctrl-2 = <&dcan1_pins_default>;
    };
    
    &atl {
    	assigned-clocks = <&abe_dpll_sys_clk_mux>,
    			  <&atl_gfclk_mux>,
    			  <&dpll_abe_m2x2_ck>,
    			  <&atl_clkin1_ck>,
    			  <&atl_clkin2_ck>;
    	assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
    	assigned-clock-rates = <0>, <0>,  <361267200>,
    			       <11289600>, <11289600>;
    
    	status = "disabled";
    
    	atl2 {
    		bws = <DRA7_ATL_WS_MCASP2_FSX>;
    		aws = <DRA7_ATL_WS_MCASP3_FSX>;
    	};
    };
    
    &mcasp1 {
    	#sound-dai-cells = <0>;
    	fck_parent = "atl_clkin2_ck";
    
    	pinctrl-names = "default";
    	pinctrl-0 = <&mcasp1_pins>;
    
    	status = "okay";
    
    	op-mode = <0>;          /* MCASP_IIS_MODE */
    	tdm-slots = <2>;
    	/* 16 serializer */
    	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
    		0 0 0 1
    		1 1 1 1
    		0 0 0 0
    		0 0 0 0
    	>;
    	tx-num-evt = <8>;
    	rx-num-evt = <8>;
    	async;
    };
    
    &mcasp2 {
    	#sound-dai-cells = <0>;
    	fck_parent = "atl_clkin2_ck";
    
    	pinctrl-names = "default";
    	pinctrl-0 = <&mcasp2_pins>;
    
    	status = "okay";
    
    	op-mode = <0>;          /* MCASP_IIS_MODE */
    	tdm-slots = <2>;
    	/* 16 serializer */
    	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
    		2 2 2 2
    		0 0 0 0
    		0 0 0 0
    		0 0 0 0
    	>;
    	tx-num-evt = <8>;
    	rx-num-evt = <8>;
    	async;
    };
    
    &mcasp3 {
    	#sound-dai-cells = <0>;
    	fck_parent = "atl_clkin2_ck";
    
    	pinctrl-names = "default";
    	pinctrl-0 = <&mcasp3_pins>;
    
    	status = "okay";
    
    	op-mode = <0>;          /* MCASP_IIS_MODE */
    	tdm-slots = <2>;
    	/* 4 serializer */
    	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
    		1 2 0 0
    	>;
    	tx-num-evt = <8>;
    	rx-num-evt = <8>;
    };
    
    &mcasp4 {
    	#sound-dai-cells = <0>;
    	fck_parent = "atl_clkin2_ck";
    
    	pinctrl-names = "default";
    	pinctrl-0 = <&mcasp4_pins>;
    
    	status = "okay";
    
    	op-mode = <0>;          /* MCASP_IIS_MODE */
    	tdm-slots = <2>;
    	/* 4 serializer */
    	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
    		2 0 0 0
    	>;
    	tx-num-evt = <8>;
    	rx-num-evt = <8>;
    };
    
    &mcasp8 {
    	#sound-dai-cells = <0>;
    	fck_parent = "atl_clkin2_ck";
    
    	pinctrl-names = "default";
    	pinctrl-0 = <&mcasp8_pins>;
    
    	status = "okay";
    
    	op-mode = <0>;          /* MCASP_IIS_MODE */
    	tdm-slots = <2>;
    	/* 4 serializer */
    	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
    		2 1 0 0
    	>;
    	tx-num-evt = <8>;
    	rx-num-evt = <8>;
    };
    
    &mailbox5 {
    	status = "okay";
    	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
    		status = "okay";
    	};
    	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
    		status = "okay";
    	};
    };
    
    &mailbox6 {
    	status = "okay";
    	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
    		status = "okay";
    	};
    	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
    		status = "okay";
    	};
    };
    
    &mmu0_dsp1 {
    	status = "okay";
    };
    
    &mmu1_dsp1 {
    	status = "okay";
    };
    
    &mmu0_dsp2 {
    	status = "okay";
    };
    
    &mmu1_dsp2 {
    	status = "okay";
    };
    
    &mmu_ipu1 {
    	status = "okay";
    };
    
    &mmu_ipu2 {
    	status = "okay";
    };
    
    &ipu2 {
    	status = "okay";
    	memory-region = <&ipu2_cma_pool>;
    	mboxes = <&mailbox6 &mbox_ipu2_ipc3x>;
    	timers = <&timer3>;
    	watchdog-timers = <&timer4>, <&timer9>;
    };
    
    &ipu1 {
    	status = "okay";
    	memory-region = <&ipu1_cma_pool>;
    	mboxes = <&mailbox5 &mbox_ipu1_ipc3x>;
    	timers = <&timer11>;
    	watchdog-timers = <&timer7>, <&timer8>;
    };
    
    &dsp1 {
    	status = "okay";
    	memory-region = <&dsp1_cma_pool>;
    	mboxes = <&mailbox5 &mbox_dsp1_ipc3x>;
    	timers = <&timer5>;
    	watchdog-timers = <&timer10>;
    };
    
    &dsp2 {
    	status = "okay";
    	memory-region = <&dsp2_cma_pool>;
    	mboxes = <&mailbox6 &mbox_dsp2_ipc3x>;
    	timers = <&timer6>;
    };
    
    &dss {
    	status = "okay";
    
    	vdda_video-supply = <&ldoln_reg>;
    
    	ports {
    		#address-cells = <1>;
    		#size-cells = <0>;
    		status = "disabled";
    
    		port@lcd3 {
    			reg = <2>;
    
    			dpi_out3: endpoint {
    				remote-endpoint = <&fpd_in>;
    				data-lines = <24>;
    			};
    		};
    	};
    };
    
    &hdmi {
    	status = "disabled";
    	vdda-supply = <&ldo3_reg>;
    
    	port {
    		hdmi_out: endpoint {
    			remote-endpoint = <&tpd12s015_in>;
    		};
    	};
    };
    
    #if 0
    &vip1 {
    	status = "okay";
    };
    
    video_in: &vin1a {
    	status = "okay";
    	endpoint@0 {
    		slave-mode;
    		remote-endpoint = <&onboardLI>;
    	};
    };
    
    #endif
    
    
    &vip2 {
    	status = "okay";
    };
    
    video_in: &vin4b {
    	status = "okay";
    	endpoint@0 {
    		slave-mode;
    		remote-endpoint = <&onboardLI>;
    	};
    };
    
    
    #include "dra7xx-jamr3.dtsi"
    #if 0
    &tvp_5158{
    	mux-gpios = <&pcf_hdmi 3 GPIO_ACTIVE_HIGH>,	/*CAM_FPD_MUX_S0*/
    		    <&pcf_jamr3_21 8 GPIO_ACTIVE_LOW>;	/*SEL_TVP_FPD*/
    };
    #endif
    

    3.  * DRA746 eMMC?  Boots ,但安装 eMMC1接口(包括 TS3A27518?)

    [Kevin ]这是我们的 主要 问题,即 日期代码224/2245引导 时出现错误消息(有时是紧急消息) ,电压为3.3V:

    3.1 DRA746从 eMMC2 (/dev/mmcblk1、rootfs 存储器)引导、但在安装 FS 过程中、它将尝试读取 MMC1 (/dev/mmcblk0)、并出现以下错误消息:

    "[3.857446]  mmcblk0:错误-84传输数据、扇区2、nr 6、cmd 响应0x900、卡状态0x0"。

    3.2是、包含 TS3A27518。

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    您的原理图显示 SDCD (卡检测)被1.8V 上拉、这将解释它为什么仅与此 IO 电平一同工作。

    在最新的软件(v6)上、您遇到与未检测到 SD 相关的"正在等待根设备"错误、这也表明了这一点。

     您已禁用此行、但它可用于使 GPIO 控制 SDCD ->/CD-GPIO =<&GPIO6 27 GPIO_ACTIVE_LOW>;

    由于您要在同一控制器上多路复用 eMMC 器件和 SD 卡、因此您不希望将 Card Detect 始终拉高、或者可以将 SD 和 eMMC 拆分到器件 MMC1/2/3/4上的任何其他控制器上。

    是否从 MMC2上的 eMMC 器件引导?

  • 请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。

    大家好、Macro。

    感谢您的回复。

    据我所知、客户电路板也可以从 MMC2引导。

    对于最近几天的调试、客户尝试跳过此问题。

    因为 多路复用器 仅用于出厂 MP、不适用于正常使用。

    我想我们可以关闭这个主题。

    再次感谢

    吉布斯