请注意,本文内容源自机器翻译,可能存在语法或其它翻译错误,仅供参考。如需获取准确内容,请参阅链接中的英语原文或自行翻译。
器件型号:MSP430FR2532 大家好!
我很难在 LED2保持运行的时间上增加延迟。
在以下代码中、没有出现延迟、一切正常、我得到了所需的消耗量。
#include <msp430.h> // Generic MSP430 Device Include #include "driverlib.h" // MSPWare Driver Library #include "captivate.h" // CapTIvate Touch Software Library #include "CAPT_App.h" // CapTIvate Application Code #include "CAPT_BSP.h" // CapTIvate EVM Board Support Package void main(void) { // // Initialize the MCU // BSP_configureMCU() sets up the device IO and clocking // The global interrupt enable is set to allow peripherals // to wake the MCU. // WDTCTL = WDTPW | WDTHOLD; BSP_configureMCU(); __bis_SR_register(GIE); // // Start the CapTIvate application // CAPT_appStart(); // // Background Loop // while(1) { // // Run the captivate application handler. // Set LED1 while the app handler is running, // and set LED2 if proximity is detected // on any sensor. // LED1_ON; if(CAPT_appHandler()==true) LED2_ON; else LED2_OFF; LED1_OFF; // // This is a great place to add in any // background application code. // __no_operation(); // // End of background loop iteration // Go to sleep if there is nothing left to do // CAPT_appSleep(); } // End background loop } // End main()
工程会成功构建;
但是、当我添加如下延迟(第94行)时、项目不会生成;
/* --COPYRIGHT--,BSD * Copyright (c) 2017, Texas Instruments Incorporated * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * * Neither the name of Texas Instruments Incorporated nor the names of * its contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * --/COPYRIGHT--*/ //***************************************************************************** // Development main.c for MSP430FR2633, MSP430FR2533, MSP430FR2632, and // MSP430FR2532. // // This starter application initializes the CapTIvate touch library // for the touch panel specified by CAPT_UserConfig.c/.h via a call to // CAPT_appStart(), which initializes and calibrates all sensors in the // application, and starts the CapTIvate interval timer. // // Then, the capacitive touch interface is driven by calling the CapTIvate // application handler, CAPT_appHandler(). The application handler manages // whether the user interface (UI) is running in full active scan mode, or // in a low-power wake-on-proximity mode. // // The CapTIvate application handler will return true if proximity was // detected on any of the sensors in the application, which is used here // to control the state of LED2. LED1 is set while the background loop enters // the handler, and is cleared when the background loop leaves the handler. // // \version 1.83.00.05 // Released on May 15, 2020 // //***************************************************************************** #include <msp430.h> // Generic MSP430 Device Include #include "driverlib.h" // MSPWare Driver Library #include "captivate.h" // CapTIvate Touch Software Library #include "CAPT_App.h" // CapTIvate Application Code #include "CAPT_BSP.h" // CapTIvate EVM Board Support Package void main(void) { // // Initialize the MCU // BSP_configureMCU() sets up the device IO and clocking // The global interrupt enable is set to allow peripherals // to wake the MCU. // WDTCTL = WDTPW | WDTHOLD; BSP_configureMCU(); __bis_SR_register(GIE); // // Start the CapTIvate application // CAPT_appStart(); // // Background Loop // while(1) { // // Run the captivate application handler. // Set LED1 while the app handler is running, // and set LED2 if proximity is detected // on any sensor. // LED1_ON; if(CAPT_appHandler()==true) LED2_ON; // Add delay for 5 seconds delay(5000000); // 5 seconds delay else LED2_OFF; LED1_OFF; // // This is a great place to add in any // background application code. // __no_operation(); // // End of background loop iteration // Go to sleep if there is nothing left to do // CAPT_appSleep(); } // End background loop } // End main()
我在构建控制台中得到以下编译失败信息;
我们将感谢您提供任何支持/指导。 如果您需要任何进一步的信息、请告诉我。