请注意，本文内容源自机器翻译，可能存在语法或其它翻译错误，仅供参考。如需获取准确内容，请参阅链接中的英语原文或自行翻译。
器件型号：CC1310 主题中讨论的其他器件：WMBUS、
我正在处理基于 EasyLinkEcho (RX/TX)示例的项目(CCS 12.0.00009中的 SimpleLink CC13x0 SDK v4.20.02.07)。
同时、我将在不同的器件集(也是 CC1310)上使用 wMBus 堆栈(CCS 8.1.0.00011中的 wmbus-cc13xx-rtos-2.0.0)。
我想创建一个收集器设备、该设备能够接收基于 EasyLink 的消息和 wMBus 电报(C 模式、可能是 T 模式)。
我根据 C 模式 wMBus SmartRF_SETTINGS (SF_cc13xx_868_95.c)修改了 EasyLink 中的 SmartRF_settings.c、但为了能够在 CCS 12中构建基于 EasyLink 的工程、必须排除某些参数。
#include <ti/devices/DeviceFamily.h>
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
#include DeviceFamily_constructPath(driverlib/rf_prop_cmd.h)
#include <ti/drivers/rf/RF.h>
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_genfsk.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_genfsk.h)
#include "smartrf_settings.h"
uint32_t txShapeCMode[] = {0x00000000, 0x00000000, 0x00000000, 0x440F0200, 0xD9D8CA96, 0xD9D9D9D9};
// TI-RTOS RF Mode Object
RF_Mode RF_prop =
{
.rfMode = RF_MODE_PROPRIETARY_SUB_1,
.cpePatchFxn = &rf_patch_cpe_genfsk,
.mcePatchFxn = 0,
.rfePatchFxn = &rf_patch_rfe_genfsk,
};
// Overrides for CMD_PROP_RADIO_DIV_SETUP
uint32_t pOverrides[] =
{
//Run the MCE and RFE patches
MCE_RFE_OVERRIDE(1,0,0,1,0,0),
// override_synth_prop_863_930_div5.xml
// Synth: Set recommended RTRIM to 7
HW_REG_OVERRIDE(0x4038,0x0037),
// Synth: Set Fref to 4 MHz
(uint32_t)0x000684A3,
// Synth: Configure fine calibration setting
HW_REG_OVERRIDE(0x4020,0x7F00),
// Synth: Configure fine calibration setting
HW_REG_OVERRIDE(0x4064,0x0040),
// Synth: Configure fine calibration setting
(uint32_t)0xB1070503,
// Synth: Configure fine calibration setting
(uint32_t)0x05330523,
// Synth: Set loop bandwidth after lock to 20 kHz
(uint32_t)0x0A480583,
// Synth: Set loop bandwidth after lock to 20 kHz
(uint32_t)0x7AB80603,
// Synth: Configure VCO LDO (in ADI1, set VCOLDOCFG=0x9F to use voltage input reference)
ADI_REG_OVERRIDE(1,4,0x9F),
// Synth: Configure synth LDO (in ADI1, set SLDOCTL0.COMP_CAP=1)
ADI_HALFREG_OVERRIDE(1,7,0x4,0x4),
// Synth: Use 24 MHz XOSC as synth clock, enable extra PLL filtering
(uint32_t)0x02010403,
// Synth: Configure extra PLL filtering
(uint32_t)0x00108463,
// Synth: Increase synth programming timeout (0x04B0 RAT ticks = 300 us)
(uint32_t)0x04B00243,
// override_phy_rx_aaf_bw_0xd.xml
// Rx: Set anti-aliasing filter bandwidth to 0xD (in ADI0, set IFAMPCTL3[7:4]=0xD)
ADI_HALFREG_OVERRIDE(0,61,0xF,0xD),
// override_phy_gfsk_rx.xml
// Rx: Set LNA bias current trim offset to 3
(uint32_t)0x00038883,
// Rx: Freeze RSSI on sync found event
HW_REG_OVERRIDE(0x6084,0x35F1),
// override_phy_gfsk_pa_ramp_agc_reflevel_0x2e.xml
// Tx: Configure PA ramping setting and set AGC reference level to 0x2E
HW_REG_OVERRIDE(0x6088,0x082E),
// Tx: Configure PA ramping setting and set AGC settle wait = (0x7+1)*2 = 16 samples
HW_REG_OVERRIDE(0x608C,0x0407),
// override_phy_rx_rssi_offset_5db.xml
// Rx: Set RSSI offset to adjust reported RSSI by +5 dB
(uint32_t)0x00FB88A3,
// TX power override
// Tx: Set PA trim to max (in ADI0, set PACTL0=0xF8)
ADI_REG_OVERRIDE(0,12,0xF8),
// AGC winsize 2 samples
HW_REG_OVERRIDE(0x6064,0x1101),
// CS threshold to �107 dBm
HW_REG_OVERRIDE(0x6090,0xA095),
// Let the patch control the correlator setting
(uint32_t)0x00048103,
// Clear state in internal radio register due to frequency change
HW_REG_OVERRIDE(0x51F8,0x0000),
HW_REG_OVERRIDE(0x52B4, 0x4000),
// Set divider bias to disabled
HW32_ARRAY_OVERRIDE(0x405C,1),
(uint32_t)0x18000200,
// TX shape in T-mode
//0xC0040031,
//(uint32_t)&txShapeTMode[0],
// TX shape in C-mode
0xC0040031,
(uint32_t)&txShapeCMode[0],
(uint32_t)0xFFFFFFFF,
};
// CMD_PROP_RADIO_DIV_SETUP
rfc_CMD_PROP_RADIO_DIV_SETUP_t RF_cmdPropRadioDivSetup =
{
.commandNo = 0x3807,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.modulation.modType = 0x0,
.modulation.deviation = 0xB4, // T-Mode: 0xC8, C-Mode: 0xB4. /* According to swra522d we have to change the deviation setting for C-meters */
.symbolRate.preScale = 0xC,
.symbolRate.rateWord = 0xCCCD,
.rxBw = 0x27,
.preamConf.nPreamBytes = 0x4,
.preamConf.preamMode = 0x0,
.formatConf.nSwBits = 0x10,
.formatConf.bBitReversal = 0x0,
.formatConf.bMsbFirst = 0x1,
.formatConf.fecMode = 0x0,
.formatConf.whitenMode = 0x0,
.config.frontEndMode = 0x0,
.config.biasMode = 0x1,
.config.analogCfgMode = 0x0,
.config.bNoFsPowerUp = 0x0,
.pRegOverride = pOverrides,
.txPower = 0xA73F,
.centerFreq = 0x0364,
.intFreq = 0x8000,
.loDivider = 0x05,
};
// CMD_FS
rfc_CMD_FS_t RF_cmdFs =
{
.commandNo = 0x0803,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.frequency = 0x0364,
.fractFreq = 0xF334,
.synthConf.bTxMode = 0x0,
.synthConf.refFreq = 0x0,
.__dummy0 = 0x00,
.__dummy1 = 0x00,
.__dummy2 = 0x00,
.__dummy3 = 0x0000,
};
// CMD_PROP_TX
rfc_CMD_PROP_TX_t RF_cmdPropTx =
{
.commandNo = 0x3803,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.pktConf.bFsOff = 0x0,
.pktConf.bUseCrc = 0x0,
// .pktConf.bCrcIncSw = 0x0,
// .pktConf.bCrcIncHdr = 0x0,
// .numHdrBits = 0x00,
.pktLen = 0x0000,
// .startConf.bExtTxTrig = 0x0,
// .startConf.inputMode = 0x0,
// .startConf.source = 0x0,
// .preTrigger.triggerType = 0x0,
// .preTrigger.bEnaCmd = 0x0,
// .preTrigger.triggerNo = 0x0,
// .preTrigger.pastTrig = 0x0,
// .preTime = 0x00000000,
.syncWord = 0x0000543D,
.pPkt = 0, /*INSERT APPLICABLE POINTER: (uint8_t*)&xxx */
};
// CMD_PROP_RX
rfc_CMD_PROP_RX_t RF_cmdPropRx =
{
.commandNo = 0x3804,
.status = 0x0000,
.pNextOp = 0, /*INSERT APPLICABLE POINTER: (uint8_t*)&xxx */
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.pktConf.bFsOff = 0x0,
.pktConf.bRepeatOk = 0x0,
.pktConf.bRepeatNok = 0x0,
.pktConf.bUseCrc = 0x0,
// .pktConf.bCrcIncSw = 0x0,
// .pktConf.bCrcIncHdr = 0x0,
.pktConf.endType = 0x0,
.pktConf.filterOp = 0x0,
.rxConf.bAutoFlushIgnored = 0x0,
.rxConf.bAutoFlushCrcErr = 0x0,
.rxConf.bIncludeHdr = 0x0,
.rxConf.bIncludeCrc = 0x0,
.rxConf.bAppendRssi = 0x0,
.rxConf.bAppendTimestamp = 0x0,
.rxConf.bAppendStatus = 0x0,
.syncWord = 0x0000543D,
// .syncWord1 = 0x00000000,
.maxPktLen = 0x0000,
// .hdrConf.numHdrBits = 0x0,
// .hdrConf.lenPos = 0x0,
// .hdrConf.numLenBits = 0x0,
// .addrConf.addrType = 0x0,
// .addrConf.addrSize = 0x0,
// .addrConf.addrPos = 0x0,
// .addrConf.numAddr = 0x0,
// .lenOffset = 0x00,
.endTrigger.triggerType = 0x0,
.endTrigger.bEnaCmd = 0x0,
.endTrigger.triggerNo = 0x0,
.endTrigger.pastTrig = 0x0,
.endTime = 0x00000000,
// .pAddr = 0, /*INSERT APPLICABLE POINTER: (uint8_t*)&xxx */
.pQueue = 0, /*INSERT APPLICABLE POINTER: (dataQueue_t*)&xxx */
.pOutput = 0, /*INSERT APPLICABLE POINTER: (uint8_t*)&xxx */
};
但是、EasyLink 接收器不接收来自 wMBus "Meter"(CC1310的 wmbus 堆栈、采用 APL_CC13XX_Meter_T2_C2和"wmbus_setMode (WMBUS_MODE_C2)；"、而不是默认的"wmbus_setMode (WMBUS_MODE_T2)；")的数据。
基于 wMBus "收集器"( 具有 Serial_CC13XX_Collector_C2的 CC1310的 wmbus 堆栈)的预先测试成功接收发送的数据包。
在具有连续 RX 的 SmartRF Studio 7中、可以看到尖峰(-20dBm)、但也没有接收到数据包。
SmartRF 设置： 
很遗憾、我无法确认我的设置、但在这里找到了一条数据包应收的声明： 如何将 Smart RF Studio 配置为 T&C 模式？
1) 1)在 C 模式(和/或 T 模式)下、SmartRF Studio 中应使用哪些设置来接收从 wMBus 器件发送的数据包？
2) 2)是否可以使用 EasyLink 抽象层("EasyLink_receiveAsync")接收 wMBus (C 模式和/或 T 模式)电报？
2.1)如果是、我如何实现它？
2.2)否则、在收集器端并行使用简单 RX/TX 框架和 wMBus (数据可在更高的级别上处理)可能会是什么解决方案？
提前感谢！
