• 状态
  • 已锁定 已锁定
  • 回复 9 回复
  • 订户 30 订户
  • 视图 3696 视图
  • 用户 0 会员在此处
选项
选项
相关

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

F28377烧写程序时会连续烧写CPU1和CPU2？

user5195598
Intellectual 830 points
Other Parts Discussed in Thread: CONTROLSUITE, TMDSCNCD28379D

工程建立后，第一次烧写时会跳出个选项烧写CPU1、CPU2，当时选错了，把两个都√了，现在找不到这个界面了，每次JTAG烧写时都是连续烧写CPU1和CPU2，设置的界面找不到了，哪位能提供下？

  • 0
    TI__Guru**** 252096 points

    您指的是上图？

  • 0 回复 Susan Yang
    Intellectual 830 points

    对的，就是这个---------我怎么找不出来啊，“Project References”下是这个界面

  • 0
    TI__Mastermind 43911 points

    双核调试C28x_Microcontroller_ODW_2-0.pdf建议您选择两个，烧录时按照这个文档：

  • 0 回复 Susan Yang
    Intellectual 505 points
    您好，我选择CPU1的时候烧写成功，但是选择CPU2或者CPU1、2都选的时候烧写失败，报错说我CPU2目标未连接，您知道这是什么问题吗？谢谢您的回答！
  • 0 回复 user5739360
    TI__Guru 60308 points
    “您好，我选择CPU1的时候烧写成功，但是选择CPU2或者CPU1、2都选的时候烧写失败，报错说我CPU2目标未连接，您知道这是什么问题吗？谢谢您的回答！“
    Eric:
    可以考虑用target configuration 这个窗口，然后右键点击芯片的对应的目标配置文件ccxml文件，然后进入DEBUG界面，再该界面下，连接CPU1，烧写CPU1, 再连接CPU2， 烧写CPU2.
  • 0 回复 Eric Ma
    Intellectual 505 points
    您好，我就是这么做的。CPU1烧写没问题，CPU2报错。可是我在买来的开发板上烧写完全一样的代码，CPU1、2都没有问题，请问我这个是硬件的问题吗？
  • 0 回复 user5739360
    TI__Guru 60308 points
    ”您好，我就是这么做的。CPU1烧写没问题，CPU2报错。可是我在买来的开发板上烧写完全一样的代码，CPU1、2都没有问题，请问我这个是硬件的问题吗？“
    Eric:
    那CPU2能不能连接上呢？你选择CPU2后，点击connect target ,有什么反应？
    有没截图和报错信息看看。
  • 0 回复 Eric Ma
    Intellectual 505 points
    您好，连接正常。在CPU1已连接并下载了代码的情况下，连接CPU2下载代码报错如下：
    C28xx_CPU2: Error: (Error -1135 @ 0xC0CC) The debug probe reported an error. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation. (Emulation package 6.0.14.5)
    C28xx_CPU2: Trouble Halting Target CPU: (Error -1044 @ 0x0) The debug probe reported an error. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation. (Emulation package 6.0.14.5)
    C28xx_CPU2: Error: (Error -1135 @ 0xC0CC) The debug probe reported an error. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation. (Emulation package 6.0.14.5)
    C28xx_CPU2: Unable to determine target status after 20 attempts
    C28xx_CPU2: Failed to remove the debug state from the target before disconnecting. There may still be breakpoint op-codes embedded in program memory. It is recommended that you reset the emulator before you connect and reload your program before you continue debugging
    C28xx_CPU1: Error: (Error -1044 @ 0x0) The debug probe reported an error. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation. (Emulation package 6.0.14.5)
    C28xx_CPU1: Error: (Error -1135 @ 0x3FF16A) The debug probe reported an error. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation. (Emulation package 6.0.14.5)
    C28xx_CPU1: Unable to determine target status after 20 attempts
    C28xx_CPU1: Failed to remove the debug state from the target before disconnecting. There may still be breakpoint op-codes embedded in program memory. It is recommended that you reset the emulator before you connect and reload your program before you continue debugging
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0007026D@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x00130@Program: target is not connected
    C28xx_CPU2: Error writing the PLL values. (Flash algoirthm returned error code). Operation cancelled.
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x0005D200@Data: target is not connected
    C28xx_CPU2: File Loader: Memory write failed: Unknown error
    C28xx_CPU2: GEL: File: D:\ccs6\ccs_work_dir\lab01_LED\Debug\lab01_LED.out: Load failed.
    C28xx_CPU2: Error occurred during flash operation: Could not read register PC: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x0005F800@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x00000@Program: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Cannot enable while the target is disconnected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0007026D@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error setting the GSxMSEL register for Flash operations
    C28xx_CPU2: Error occurred during flash operation: Failed to run target while trying to execute pwrite_en.alg
    C28xx_CPU2: Flash operation timed out waiting for the algorithm to complete. Operation cancelled.
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0007026D@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0005F444@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0007026D@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not write 0x0005D200@Data: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x5D200@Program: target is not connected
    C28xx_CPU2: Error occurred during flash operation: Could not read 0x0007026D@Data: target is not connected
    C28xx_CPU2: Flash Programmer: Unable to acquire the clock semaphore. The other core might still be accessing the clock registers. Operation Cancelled.
    C28xx_CPU2: Error occurred during flash operation: Could not write register PC: target is not connected
    谢谢您！
  • 0 回复 user5739360
    TI__Guru 60308 points
    Eric:

    这种情况下建议仔细检查一下硬件，检测电源是否稳定，芯片的最小系统和TI的推荐是否一致。
    C:\ti\controlSUITE\development_kits\~controlCARDs\TMDSCNCD28379D_v1_0\R1_3