am335x启动安卓的时候一直显示init: untracked pid xxx exited

guan hao

Other Parts Discussed in Thread: TPS65910

init: untracked pid 133 exited
[   21.620727] init: untracked pid 214 exited
[   26.947296] init: untracked pid 221 exited
[   34.322906] init: untracked pid 228 exited
[   36.742980] init: untracked pid 235 exited
[   44.253082] init: untracked pid 242 exited
[   46.672698] init: untracked pid 249 exited
[   52.094116] init: untracked pid 256 exited
[   56.513092] init: untracked pid 263 exited
[   61.943115] init: untracked pid 270 exited

shell 命令也能用，但是一直打印这样的错误。是什么原因造成的呢？

10 年多前

0 guan hao 10 年多前

Prodigy 130 points

最后打打印信息如下：

[    2.861938] EXT4-fs (mmcblk0p2): recovery complete
[    2.870483] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode.)
[    2.879028] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.885925] Freeing init memory: 348K
[    2.927124] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom.
[    3.025299] init: cannot open '/initlogo.rle'
[    3.060882] init: cannot find '/system/bin/sgx/rc.pvr', disabling 'pvr'
[    3.070892] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[    3.108306] init: cannot find '/system/etc/install-recovery.sh', disabling '
[    3.136657] android_usb: already disabled
[    3.141174] mtp_bind_config
[    3.144195] adb_bind_config
[    3.223480] adb_open
root@android:/ # [    5.199554] init: untracked pid 64 exited
[    9.030517] init: untracked pid 149 exited
[   14.677398] init: untracked pid 216 exited
[   22.002593] init: untracked pid 223 exited

0 Yaoming Qin 10 年多前回复 guan hao

TI__Mastermind 35157 points

有完整的log吗？ lcd有反应吗？

0 guan hao 10 年多前回复 Yaoming Qin

Prodigy 130 points

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.2.0 (root@ubuntu) (gcc version 4.4.3 (GCC) ) #5 5
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructie
[    0.000000] Machine: am335xevm
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] AM335X ES2.0 (sgx neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa4
[    0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=f
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 250172k/250172k available, 11972k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   ( 16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0761000   (7524 kB)
[    0.000000]       .init : 0xc0761000 - 0xc07b8000   ( 348 kB)
[    0.000000]       .data : 0xc07b8000 - 0xc081e9f0   ( 411 kB)
[    0.000000]        .bss : 0xc081ea14 - 0xc09745d8   (1367 kB)
[    0.000000] NR_IRQS:396
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrus
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[    0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 1s
[    0.000000] Console: colour dummy device 80x30
[    0.000152] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
[    0.089233] pid_max: default: 32768 minimum: 301
[    0.089355] Security Framework initialized
[    0.089416] Mount-cache hash table entries: 512
[    0.089782] CPU: Testing write buffer coherency: ok
[    0.089843] ftrace: allocating 21678 entries in 64 pages
[    0.146026] omap_hwmod: pruss: failed to hardreset
[    0.146759] print_constraints: dummy:
[    0.146972] NET: Registered protocol family 16
[    0.147918] OMAP GPIO hardware version 0.1
[    0.148803] omap_mux_init: Add partition: #1: core, flags: 0
[    0.149871] omap_i2c.1: alias fck already exists
[    0.150329] omap2_mcspi.1: alias fck already exists
[    0.150390] omap2_mcspi.2: alias fck already exists
[    0.150543] edma.0: alias fck already exists
[    0.150543] edma.0: alias fck already exists
[    0.150543] edma.0: alias fck already exists
[    0.158325] bio: create slab <bio-0> at 0
[    0.159149] SCSI subsystem initialized
[    0.159973] usbcore: registered new interface driver usbfs
[    0.160064] usbcore: registered new interface driver hub
[    0.160186] usbcore: registered new device driver usb
[    0.160308] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3
[    0.160430] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1
[    0.160827] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[    0.161926] tps65910 1-002d: JTAGREVNUM 0x0
[    0.164062] print_constraints: VRTC:
[    0.165374] print_constraints: VIO: at 1500 mV
[    0.167541] print_constraints: VDD1: 600 <--> 1500 mV at 1325 mV normal
[    0.169708] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal
[    0.170593] print_constraints: VDD3: 5000 mV
[    0.171844] print_constraints: VDIG1: at 1800 mV
[    0.173156] print_constraints: VDIG2: at 1800 mV
[    0.174438] print_constraints: VPLL: at 1800 mV
[    0.175720] print_constraints: VDAC: at 1800 mV
[    0.177001] print_constraints: VAUX1: at 1800 mV
[    0.178283] print_constraints: VAUX2: at 3300 mV
[    0.179565] print_constraints: VAUX33: at 3300 mV
[    0.180847] print_constraints: VMMC: at 3300 mV
[    0.181091] tps65910 1-002d: No interrupt support, no core IRQ
[    0.181518] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.182006] Bluetooth: Core ver 2.16
[    0.182067] NET: Registered protocol family 31
[    0.182098] Bluetooth: HCI device and connection manager initialized
[    0.182098] Bluetooth: HCI socket layer initialized
[    0.182098] Bluetooth: L2CAP socket layer initialized
[    0.182128] Bluetooth: SCO socket layer initialized
[    0.182312] Switching to clocksource gp timer
[    0.197448] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    0.197631] musb-hdrc musb-hdrc.0: dma type: pio
[    0.197814] MUSB0 controller's USBSS revision = 4ea20800
[    0.198181] musb-hdrc musb-hdrc.0: USB OTG mode controller at d083c000 using8
[    0.198455] musb-hdrc musb-hdrc.1: dma type: pio
[    0.198577] MUSB1 controller's USBSS revision = 4ea20800
[    0.198669] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[    0.198760] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus numb1
[    0.198883] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.198883] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1
[    0.198913] usb usb1: Product: MUSB HDRC host driver
[    0.198913] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd
[    0.198913] usb usb1: SerialNumber: musb-hdrc.1
[    0.199310] hub 1-0:1.0: USB hub found
[    0.199340] hub 1-0:1.0: 1 port detected
[    0.199676] musb-hdrc musb-hdrc.1: USB Host mode controller at d083e800 usin9
[    0.200012] NET: Registered protocol family 2
[    0.200195] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.200531] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.200622] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.200714] TCP: Hash tables configured (established 8192 bind 8192)
[    0.200714] TCP reno registered
[    0.200714] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.200744] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.200897] NET: Registered protocol family 1
[    0.201171] RPC: Registered named UNIX socket transport module.
[    0.201171] RPC: Registered udp transport module.
[    0.201171] RPC: Registered tcp transport module.
[    0.201171] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.201385] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.288787] ashmem: initialized
[    0.289031] VFS: Disk quotas dquot_6.5.2
[    0.289062] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.289825] fuse init (API version 7.17)
[    0.290008] msgmni has been set to 488
[    0.290924] io scheduler noop registered
[    0.290924] io scheduler deadline registered
[    0.290985] io scheduler cfq registered (default)
[    0.291473] Could not set LED4 to fully on
[    0.303161] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[    0.965057] console [ttyO0] enabled
[    0.969146] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[    0.976806] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[    0.984466] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[    0.992065] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[    0.999694] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[    1.011871] brd: module loaded
[    1.017547] loop: module loaded
[    1.020996] i2c-core: driver [tsl2550] using legacy suspend method
[    1.027526] i2c-core: driver [tsl2550] using legacy resume method
[    1.033966] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[    1.092895] No daughter card found on AM335x EVM
[    1.097747] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[    1.105194] The board is general purpose EVM in profile 0
[    1.111145] omap_hsmmc.0: alias fck already exists
[    1.117187] NFC Driver for TI WiLink
[    1.121490] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.128601] omap2-nand driver initializing
[    1.132965] OneNAND driver initializing
[    1.137390] CAN device driver interface
[    1.141387] CAN bus driver for Bosch D_CAN controller 1.0
[    1.192932] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[    1.199401] davinci_mdio davinci_mdio.0: detected phy mask ffffff7e
[    1.207244] davinci_mdio.0: probed
[    1.210815] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
[    1.218231] davinci_mdio davinci_mdio.0: phy[7]: device 0:07, driver unknown
[    1.225646] PPP generic driver version 2.4.2
[    1.230285] PPP BSD Compression module registered
[    1.235229] PPP Deflate Compression module registered
[    1.240600] usbcore: registered new interface driver cdc_ether
[    1.246765] usbcore: registered new interface driver cdc_eem
[    1.252716] usbcore: registered new interface driver dm9601
[    1.258575] usbcore: registered new interface driver cdc_subset
[    1.264831] cdc_ncm: 04-Aug-2011
[    1.268249] usbcore: registered new interface driver cdc_ncm
[    1.274230] usbcore: registered new interface driver cdc_acm
[    1.280151] cdc_acm: USB Abstract Control Model driver for USB modems and ISs
[    1.288513] Initializing USB Mass Storage driver...
[    1.293731] usbcore: registered new interface driver usb-storage
[    1.300018] USB Mass Storage support registered.
[    1.304992] usbcore: registered new interface driver usbserial
[    1.311096] USB Serial support registered for generic
[    1.316467] usb 1-1: new high-speed USB device number 2 using musb-hdrc
[    1.463073] usb 1-1: New USB device found, idVendor=0424, idProduct=2512
[    1.470092] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.478027] hub 1-1:1.0: USB hub found
[    1.482025] hub 1-1:1.0: 2 ports detected
[    1.486877] usbcore: registered new interface driver usbserial_generic
[    1.493743] usbserial: USB Serial Driver core
[    1.498321] USB Serial support registered for GSM modem (1-port)
[    1.504791] usbcore: registered new interface driver option
[    1.510620] option: v0.7.2:USB Driver for GSM modems
[    1.517272] gadget: Mass Storage Function, version: 2009/09/11
[    1.523498] gadget: Number of LUNs=1
[    1.527343] lun0: LUN: removable file: (no medium)
[    1.532623] gadget: android_usb ready
[    1.536590] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[    1.542175] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus numb2
[    1.549987] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.557098] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber1
[    1.564666] usb usb2: Product: MUSB HDRC host driver
[    1.569854] usb usb2: Manufacturer: Linux 3.2.0 musb-hcd
[    1.575408] usb usb2: SerialNumber: musb-hdrc.0
[    1.580505] hub 2-0:1.0: USB hub found
[    1.584472] hub 2-0:1.0: 1 port detected
[    1.589050] mousedev: PS/2 mouse device common for all mice
[    1.595977] using rtc device, omap_rtc, for alarms
[    1.600830] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
[    1.607788] i2c /dev entries driver
[    1.611602] Linux video capture interface: v2.00
[    1.616699] usbcore: registered new interface driver uvcvideo
[    1.622680] USB Video Class driver (1.1.1)
[    1.663635] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.670135] device-mapper: uevent: version 1.0.3
[    1.675170] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-m
[    1.683990] Bluetooth: HCI UART driver ver 2.2
[    1.688659] Bluetooth: HCI H4 protocol initialized
[    1.693664] Bluetooth: HCILL protocol initialized
[    1.698577] Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0
[    1.709442] cpuidle: using governor ladder
[    1.713897] cpuidle: using governor menu
[    1.720153] usbcore: registered new interface driver usbhid
[    1.726043] usbhid: USB HID core driver
[    1.730560] logger: created 256K log 'log_main'
[    1.735443] logger: created 256K log 'log_events'
[    1.740447] logger: created 256K log 'log_radio'
[    1.745391] logger: created 256K log 'log_system'
[    1.750793] usbcore: registered new interface driver snd-usb-audio
[    1.758117] ALSA device list:
[    1.761199]   No soundcards found.
[    1.764801] oprofile: hardware counters not available
[    1.770050] oprofile: using timer interrupt.
[    1.774688] Netfilter messages via NETLINK v0.30.
[    1.779724] nf_conntrack version 0.5.0 (3908 buckets, 15632 max)
[    1.786376] ctnetlink v0.93: registering with nfnetlink.
[    1.791992] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    1.799285] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    1.805725] xt_time: kernel timezone is -0000
[    1.810485] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.816314] arp_tables: (C) 2002 David S. Miller
[    1.821197] TCP cubic registered
[    1.824768] NET: Registered protocol family 10
[    1.830230] Mobile IPv6
[    1.832824] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    1.838714] IPv6 over IPv4 tunneling driver
[    1.843780] NET: Registered protocol family 17
[    1.848449] NET: Registered protocol family 15
[    1.853149] can: controller area network core (rev 20090105 abi 8)
[    1.859710] NET: Registered protocol family 29
[    1.864379] can: raw protocol (rev 20090105)
[    1.868835] can: broadcast manager protocol (rev 20090105 t)
[    1.875213] Bluetooth: RFCOMM TTY layer initialized
[    1.880310] Bluetooth: RFCOMM socket layer initialized
[    1.885711] Bluetooth: RFCOMM ver 1.11
[    1.889617] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.895172] Bluetooth: BNEP filters: protocol multicast
[    1.900634] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.906982] Registering the dns_resolver key type
[    1.911956] VFP support v0.3: implementor 41 architecture 3 part 30 variant 3
[    1.919982] ThumbEE CPU extension supported.
[    1.924499] mux: Failed to setup hwmod io irq -22
[    1.930114] Power Management for AM33XX family
[    1.934997] Trying to load am335x-pm-firmware.bin (60 secs timeout)
[    1.941650] Copied the M3 firmware to UMEM
[    1.949981] clock: disabling unused clocks to save power
[    1.957153] Detected MACID=20:cd:39:d9:82:d2
[    1.962890] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 U)
[    1.972229] Waiting for root device /dev/mmcblk0p2...
[    2.015899] mmc0: new high speed SDHC card at address 1234
[    2.022155] mmcblk0: mmc0:1234 SA04G 3.63 GiB
[    2.028930] mmcblk0: p1 p2 p3
[    5.737548] EXT4-fs (mmcblk0p2): recovery complete
[    5.746032] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. )
[    5.754577] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    5.761474] Freeing init memory: 348K
[    5.794006] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_.
[    5.877746] init: cannot open '/initlogo.rle'
[    5.907806] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[    5.981903] init: cannot find '/system/etc/install-recovery.sh', disabling ''
[    5.994445] android_usb: already disabled
[    6.001495] mtp_bind_config
[    6.004577] adb_bind_config
[    6.150268] adb_open
root@android:/ # [    6.226562] Disabling lock debugging due to kernel taint
[    6.278717] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[    8.784881] init: untracked pid 66 exited
[   10.991088] init: untracked pid 221 exited
[   11.882934] init: untracked pid 222 exited