LAUNCHXL-CC1310: cc1310 launch board can't load program ,flash locked

tian jun

Prodigy 30 points

Part Number: LAUNCHXL-CC1310
Other Parts Discussed in Thread: UNIFLASH, CC1310

ccs and uniflash can't load progarm on cc1310 launch borad,and use flash program to force mass erase won't help

11 个月前

0 tian jun 11 个月前

Prodigy 30 points

erase complete ,but problem still exist.

0 Alex Zhang 11 个月前

TI__Mastermind 18380 points

您好，方便问一下：

1.您这边使用的是ti的开发板吗还是用的自己设计的硬件？

2.您这边是一开始就无法正常烧录还是您这边操作什么了之后才出现这个问题了？

0 tian jun 11 个月前回复 Alex Zhang

Prodigy 30 points

ti 开发板cc1310 launch，之前都能正常烧录，然后我把ti 的packetTx例程准备烧录到板子里，板子就亮红灯然后就烧不进去了

0 Alex Zhang 11 个月前回复 tian jun

TI__Mastermind 18380 points

您好，你这边先尝试一下这个，打开targetconfig里面的 ccxml文件，然后去选择您这边的开发板型号，进行尝试。

0 tian jun 11 个月前回复 Alex Zhang

Prodigy 30 points

能检测到xds110接口连接不上

0 Alex Zhang 11 个月前回复 Alex Zhang

TI__Mastermind 18380 points

Alex Zhang 说：
您好，你这边先尝试一下这个，打开targetconfig里面的 ccxml文件，然后去选择您这边的开发板型号，进行尝试

您好，您这边进行尝试了吗？

0 tian jun 11 个月前回复 Alex Zhang

Prodigy 30 points

这是测试日志

[Start: Texas Instruments XDS110 USB Debug Probe]

Execute the command:

%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -S integrity

[Result]

-----[Print the board config pathname(s)]------------------------------------

C:\Users\tianjun\AppData\Local\TEXASI~1\
CCS\CCS122~1.000\0\0\BrdDat\testBoard.dat

-----[Print the reset-command software log-file]-----------------------------

This utility has selected a 100/110/510 class product.
This utility will load the adapter 'jioxds110.dll'.
The library build date was 'Mar 10 2023'.
The library build time was '17:27:27'.
The library package version is '9.11.0.00128'.
The library component version is '35.35.0.0'.
The controller does not use a programmable FPGA.
The controller has a version number of '5' (0x00000005).
The controller has an insertion length of '0' (0x00000000).
This utility will attempt to reset the controller.
This utility has successfully reset the controller.

-----[Print the reset-command hardware log-file]-----------------------------

The scan-path will be reset by toggling the JTAG TRST signal.
The controller is the XDS110 with USB interface.
The link from controller to target is direct (without cable).
The software is configured for XDS110 features.
The controller cannot monitor the value on the EMU[0] pin.
The controller cannot monitor the value on the EMU[1] pin.
The controller cannot control the timing on output pins.
The controller cannot control the timing on input pins.
The scan-path link-delay has been set to exactly '0' (0x0000).

An error occurred while hard opening the controller.

-----[An error has occurred and this utility has aborted]--------------------

This error is generated by TI's USCIF driver or utilities.

The value is '-241' (0xffffff0f).
The title is 'SC_ERR_ROUTER_SECURE_SUBPATH'.

The explanation is:
A router subpath could not be accessed.
A security error has probably occurred.
Make sure your device is unlocked.

[End: Texas Instruments XDS110 USB Debug Probe]